Hard Drive
Store data on magnetic surface plattens.
-
Product
Motor Drive Control
-
Four motor speed drive control models ranging from a simple speed dial/display to complex machine/process synchronizers. Capable of many motor/machine control schemes, from open-loop master to closed-loop pulse-locked speed/event synchronized follower. Compatible with all motor speed drives of any size/power rating with an analog input (AC, AC Vector, DC and Servo)
-
Product
Ultrasonic Hardness Tester
-
Sinowon Innovation Metrology Manufacture Ltd.
◆ Perfect Accuracy——±3% HV, ±1.5HR, ±3%HB.◆ Microscopic Indentation—— Only high-power microscope can observe the indentation.◆ Quick Measurement——Result in 2 seconds.◆ Large LCD Display——Directly display measurement result, times count, maximum, minimal, average and deviation.◆ Friendly Operation——Operate well after short training.◆ Promised Warranty——2-Year warranty for main unit (Excludes Probe).◆ Mass Storage——Save 1000 groups measurement data.◆ Simple Calibration——Save 20 groups calibration data for invoking, improve calibration efficiency.
-
Product
Portable Hardness Tester For cast/rough surface parts
PHT-1750
-
Loaded with features, this economically priced portable hardness tester is capable of measuring the surface hardness of a broad variety of metals on flat and round surfaces. This portable hardness tester comes complete with the G impact device, calibrated test block and rugged carry case.
-
Product
2-Phase Stepper Drives Based On EtherCAT Field Bus
Nu-Step DA Series
Stepper Driver
The ADLINK Nu-Step DA Series is a stepper driver based on the EtherCAT bus featuring a 32-bit ARM processor and advanced variable current and frequency conversion technology. The driver generates less heat and motor vibration for more stable operation. It not only supports the standard EtherCAT specification, but also supports table comparison triggers for automated optical inspection (AOI) and linear comparison triggers for line scanning.
-
Product
Photocouplers/Optocouplers Motor Drive
-
The PS9xxx series, a range of motor-driving photocouplers (optocouplers), feature a high isolation voltage, high temperature operation, high output current, and high-speed switching.
-
Product
6U OpenVPX Quad Drive Storage Module
563x
-
The 5632 & 5633 support multi-terabyte storage in one 6U slot with capacities current solid state drive technologies. Four on-board SATA drives connect via the backplane via SATA controller to create a high capacity multi-slot storage array.
-
Product
Pen Type Leeb Hardness Tester
TIME®5100/5102/5104
-
Beijing TIME High Technology Ltd.
Pen Type Hardness Tester TIME®5100/5102/5104 is economically priced and suitable for quick hardness testing on metal materials, especially on-site hard testing of large, non-transportable components.
-
Product
Digital Brushless Servo Drives
DA Series
-
The DA series high performance digital servo drives integrates digital position and velocity control with built-in power supplies and the latest in PWM servo amplifier technology. Power range up to 50KVA.
-
Product
Hardness Testers
-
Dalian Taijia Technology Co.,Ltd
Digital durometer for shore hardness testing pocket size model with integrated probe● Test scale: shore hardness● Standards: DIN53505, ASTMD2240, ISO7619, JISK7215● Parameters displayed: hardness result, average value, max. value● Measurement range:0-100HA(HD)(HC)● Measurement deviation:＜1%H● Resolution: 0.1● Auto switch off● With RS232C interface● Operating conditions: 0℃ to 40℃● Power supply: 4x1.5V AAA (UM-4) battery● Battery indicator: low battery indicator● Dimensions: 162x65x38mm● Weight (not including probe):173g● Application:Shore A is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials.Shore D is designed for plastics, Formica, Epoxies and Plexiglass.shore C is designed for various foam and sponge.
-
Product
Fully-automatic Micro Hardness IRHD System
-
With high precision digital technology and servomotor technology employed, the Micro IRHD System has been designed on the concept of better operability and quality eligible for cutting-edge labs.
-
Product
6U VME Storage Module, 3 Drives, 5050 / 5051
5050
-
The 5050 is a 6U VME Storage Module with three 2.5” SSD in a single slot. Each SATA drive is accessible via front panel or RTM. Can be integrated into a multi-slot storage array using an external SATA RAID controller.
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD | VP 230036
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
Product
Durometer - Shore Hardness Tester
-
Qualitest provides quality control departments and research laboratories with an extensive range of top quality Durometer and hardness Tester for accurate hardness determination on all natural and synthetic rubber products and soft elastic materials, plastics, acrylic glass, acetates, casting resin, polyester, thermoplastics, PVC, neoprenes, hardboards, wood, leather, fruits and much more. Our products provide the highest precision (normally 0.5% or better), quality and craftsmanship, durability, “yet require” almost no calibration in many years after the purchase. Our designs are engineered so that the Durometer stays precisely within the standard requirements. Qualitest Durometers are referred to as the “Swiss watches” among other products on the market. Investing in our line of Durometer is a guarantee of accuracy and assurance for many years of operation.
-
Product
Leeb Hardness Testers
-
It is a type of non-destructive testing used to inspect large sized workpieces weighing above 1 kg.
-
Product
Rad Hard Power Sequencing
-
Renesas' radiation hardened quad power supply sequencers are designed to drive point-of load (POL) regulators that power high performance FPGAs and complex, multi-rail power systems.
-
Product
Portable Hardness Tester
-
Beijing TIME High Technology Ltd.
A compact, handheld device used for on-site measurement of a material's hardness.
-
Product
Shore Hardness Tester
-
Beijing TIME High Technology Ltd.
A device used to measure the hardness of materials like rubber, plastics, and elastomers by measuring their resistance to permanent indentation.
-
Product
High Strain Pile Driving Analyzer, Pile Testing Machine
SG-PDA
-
It is a state-of-the-art testing equipment to perform high strain pile bearing testing on piles.It will provide prediction on the pile bearing capacity, pile integrity, driving stresses and hammer performance for a given pile penetration. It is a relative low cost type of pile testing compared to static load test (MLT or CRP). The testing technique is quick and accurate.It can also be used to perform high strain pile bearing monitoring to evaluate pile driving information for pile bearing capacity, pile integrity, driving stresses and transferred energy against pile penetration. The results are essential for the actual pile driving process and to obtain valuable data on the hammer, pile & soil system for re-design on the piled foundation (if necessary).
-
Product
Signal Converters For Temperature Measurement In Direct Drive Motors
EIB 5000 series
-
*Reduced cabling*Overload protection for direct drive motors*Faster response behavior for excessive temperatures*Greater cost-effectiveness
-
Product
EtherCAT Servo Drives And Motors
-
High-performance servo motor and driver systems designed for industrial automation applications.
-
Product
Portable Hardness Tester with Printer
PHT-3500
-
State of the art, digital tester is designed to test the hardness of large hard metal parts. Loaded with useful functions and a built in mini-printer the PHT-3500 is clearly the industry leader for fast accurate hardness testing with advanced USB output and thermal printing capabilities.
-
Product
“Floppy drive” Power Split Cable
SKU-043-06
-
Female 4-pin “floppy drive” power connector on one end, and 2 female 4-pin “floppy drive” power connectors on the other end on this cable.
-
Product
Ultrasonic Portable Hardness Tester
UCI-3000
-
Advanced Ultrasonic Hardness Tester UCI 3000 applies ultrasonic contact impedance method to do comparative hardness measurement for testing pieces, with the high accuracy, efficiency, portability and easy operation. UCI 3000 is a high-precision portable device for quick measuring hardness of small fogging, cast material, weld inspection, heat affected zone, Ion-nitride stamping dies and molds, forms, presses, thin walled parts, bearings, tooth flanks, etc. It is used for measuring the hardness within the ranges of main hardness scales – HB, HRC as well as HV.
-
Product
Autonomous Driving AI Decision Making ECU
ADM-AL30
Electronic Control Unit
ADM-AL30 is dedicated to Autonomous Driving Applications. Powered by Intel® 12th Gen Core i9/i7 CPU and the NVIDIA RTX 4000 SFF Ada GPU, this AI computing platform can process huge amounts of data and make crucial decisions for autonomous vehicles. Equipped with 2 x 10G Base-T and 8 x 1G Base-T1 automotive ethernet ports, as well as 8 x CAN FD and 4 x CAN 2.0 interfaces, it seamlessly integrates into any automotive ecosystem. Plus, its ISO 16750-2 and ISO 7637-2 ensure reliability and safety under the most demanding conditions.
-
Product
AC drives, Soft-Starters or Servo Drives Simulation Software
-
Product simulation software enables users to operate, program and simulate AC drives, Soft-Starters or Servo Drives directly from their computer without having the actual product present or connected. Our simulation software can be used as a demonstration tool during a sales meeting or as an interactive tool for training classes. Software available In addition we offer simulation software for dedicated markets such as pumping, mining, material handling, etc... to demonstrate the use of motor controls in simulated applications.
-
Product
Portable Hardness Tester For cast/rough parts
PHT-1850
-
State of the art, digital portable hardness tester is designed to test the hardness of cast,and large hard metal parts with rough surfaces. Loaded with useful functions only found on high priced models the PHT-1850 portable hardness tester is clearly setting a new industry standard by being the most accurate, economically priced portable hardness tester on the market today.
-
Product
Rockwell Hardness Tester
-
The most popular and widely used method of Hardness Testing, The Qualitest range of Rockwell Hardness Tester Range start from low cost analog models up to sophisticated and advanced load-cell type models. The popular, HardRocker, QualiRock, Rocky series hardness tester models have configurations suitable for Regular and/or Superficial Rockwell Hardness Testing, while our advanced Universal Hardness Tester Range can test the full Rockwell scale in addition to Brinell & Vickers. Qualitest also offers Automatic In-line hardness testers for high volume testing.
-
Product
Full-Automatic Testing Machine for Hard Board Car
U690HDIR
-
1. CCD automatic alignment, the alignment accuracy reaches ± 15μm2. Support layout test, displacement function3. Automatic marking function
-
Product
Rad Hard GaN FETs
-
Wide band gap semiconductor technologies such as Gallim Nitride Field Effect Transistors (GaN FETs) have been gaining interest for power management and conversion in space applications. These devices feature higher breakdown voltage, lower RDS(ON) and very low gate charge enabling power management systems to operate at higher switching frequencies while still achieving higher efficiency and a smaller solution footprint. There is an additional benefit from GaN devices that make them attractive to the space market. These devices are inherently immune to total ionizing dose radiation.
-
Product
Digital Durometer Digital O-Ring Hardness Kit
OHK-DD-4
-
The Digital Complete O-Ring Hardness Kit is the most convenient and accurate way to perform repeatable hardness (durometer) testing on thin materials - as thin as .050". Conforms to ASTM D-2240
