Batteries Test
-
Product
Scienlab Battery Test System - Cell Level
SL1007A
Test System
The SL1007A Scienlab Battery Test System – Cell Level enables you to accurately and productively test battery cells for automotive and industrial applications. The bidirectional power supply charges and discharges your cells under test with very high efficiency.
-
Product
Configure Battery Pack Simulator for Battery Management System (BMS) Hardware-in-the-Loop (HIL) Testing
Simulator
Customized configuration for battery pack simulator by Bloomy
-
Product
Battery Pack/Module Test Solution
-
Regenerative battery energy dischargeEnergy savingEnvironment protectionLow heat generateChannels paralleled for higher currentsCharge / discharge mode (CC, CV, CP) Constant current Constant voltage Constant powerDriving cycle simulationHigh precision measurement accuracyFast current conversionSmooth current without over shootTesting data analysis functionData recovery protection (after power failure)Independent protection of multi-channelBMS data recordingThermal chamber control integration
-
Product
Battery Data Logger
BDL-3927
-
Kongter Test & Measurement Co., Limited
BDL-3927 is updated Battery Data Logger to meet IEEE measurement standards for battery voltage, string voltage, current and ambient temperature. It is customized from 12V to 700V for different battery systems. And it has easy expansion for all battery systems. With wifi communication, you could easily view complete data and generate test report in the PC software.
-
Product
Automotive Battery Testers
-
ELAK Battery Testers are high-rate discharge testers. These testers impose a load on the battery, which is equivalent to that drawn by the starter motor from the battery, while cranking the engine. The tester studies the drop in battery voltage & indicates the condition of the battery if it is capable of starting the engine or not.
-
Product
Standard 0.49 (13.89) - 2.50 (70.87) Battery Probe
CP-4C
Battery Probe
Current Rating (Amps): 10Average Probe Resistance (mOhm): 25Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 60Full Travel (mm): 1.52Recommended Travel (mil): 40Recommended Travel (mm): 1.01Overall Length (mil): 311Overall Length (mm): 7.90Overall Length Remark: Overall length does not include tail.
-
Product
Battery Testers
-
Shanghai Beha Electronics Co., Ltd.
*can measure the resistance of rechargeable batteries and DC voltage.*can also test Ni-cd, Ni-MH, Li-ion batteries.*DC Voltage measurement.*4-wire resistance measurement.
-
Product
SLA battery charger
SBSC11Q
-
The SBSC11Q is a battery charger designed to simultaneously charge up to four SBSC11 sealed lead acid batteries or other SBS type batteries having a nominal voltage of 12.0V
-
Product
NFC Conformance Test System
T3111S
Test System
The T3111S RIDER NFC Conformance Test System is the Keysight solution for RF Analog and Digital Protocol testing of NFC, EMV and ISO devices. The Test System is based on the Keysight T1141A NFC Test Set and it is complemented by the Keysight's or FIME's robots for accurate and repeatability RF testing. Selected 3rd party positioning robots can also be supported.
-
Product
Battery Tester
CS-3001
-
The CS-3001 test system records all block voltages, total voltage and current during a discharge test. The modular design makes it easy to connect most of all battery installations, starting from a single block and ending up with 960 block voltages. Up to four parallel strings can be tested. All measuring modules are electrically isolated (600VDC CAT III, 5000VAC test voltage).
-
Product
Laser Diode Burn-in Reliability Test System
58604
Test System
The Chroma 58604 is a high density, multi-function, and temperature controlled module for laser diode burn-in and lifetime tests. Each module has up to 256 SMU channels which can source current and measure voltage in various control modes as described below.
-
Product
Battery Monitoring System
BDS-Pro
-
Eagle Eye's BDS-Pro Battery Monitoring System is designed to measure the aging status of up to 24 jars (or 24 cells) by measuring and recording: string voltage and current, as well as jar/cell voltage, internal resistance, connection resistance and temperature. The BDS-Pro Battery Monitoring Solution is the most accurate, user-friendly and economic solution for monitoring 24 jars (or 24 cells) systems using 1.0-16V batteries. Although the BDS-Pro is utilized in many industries, it is most frequently used in 24 cell, 48Vdc applications.
-
Product
Cell, Battery, And Module Test Systems
-
Maximize your testing capabilities with Maccor's hardware and software. Our comprehensive turn-key systems come bundled with all the essentials to jumpstart your testing process. Select from multiple options and configurations to match your requirements.
-
Product
In-line High-Density ICT System Series 7i
E9988GL
In-Circuit Test System
The E9988GL Keysight i3070 Series 7i Inline High-Density In-Circuit Test (ICT) system brings industry-leading ICT technologies into your automated manufacturing line, saving resources and optimizing your automated test strategy.
-
Product
Battery Monitor
BAF-M2
-
Schumacher Electric Corporation
BATTERY MONITOR• Plugs into a 12 volt automotive cigarette lighter receptacle• Allows instant monitoring of battery & charging system voltage• Constant automotive battery and charging system check with a digital readout• LED warning lights alert you when your battery or charging system is not functioning properly• Detects charging input voltage within 0.1 volts variance• Detects problems with the alternator, diode and any variance of more than 0.8 volts• Alerts you once battery drops to 12.0 volts giving you approximately one more hour of run time, depending on the system’s wattage• Digital display indicates electrical voltage of your battery• Mounted display on your car’s dashboard for constant monitoring of your electrical system Contents: (1) Battery Monitor with 12V DC plug
-
Product
Battery Conductance Tester
BT-3918
-
Kongter Test & Measurement Co., Limited
The excellent performance of BT-3918 battery conductance tester will help you pick out the weak batteries and ensure battery performance in short time measurement. This test of battery internal resistance or battery conductance is essential for stationary batteries. It is also recommended by latest regulation of IEEE 450, IEEE 1188 and IEEE 1106.
-
Product
Standard 1.17 (33.20) - 4.50 (128.00) Battery Probe
CP-2TB-8
Battery Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 88Full Travel (mm): 2.25Recommended Travel (mil): 78.7Recommended Travel (mm): 2.00Overall Length (mil): 315Overall Length (mm): 8.00Overall Length Remark: Overall length does not include tail.Recommended Drill Size: #53 or 1.51 mmRec. Mounting Hole Size (mil): 61Rec. Mounting Hole Size (mm): 1.55
-
Product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
Test Fixture
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
Product
PXI Semiconductor/IC Test System
Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
Product
Testing Solution & Battery Emulation
PLUTON
-
The PLUTON solution is a programmable DC power supply designed to function as a source or a regenerative charge.
-
Product
Battery Charger-Dischargers & Monitors
-
It is a compact and multi-functional unit with three major functions: battery charger, battery discharger and battery activator. These three functions could be used individually or comprehensively to facilitate your daily work for battery maintenance. JUNXY single battery regenerator could be applied for different cell voltages, such as 2V, 6V & 12V single cell battery regenerator, while JUNXY battery string regenerator covers 24V, 48V, 110V, 220V battery strings with different charge/discharge current selectable.
-
Product
Semiconductor Test System
TS-960e
Test System
The GENASYS Semi TS-960e PXI Express Semiconductor Test System is an integrated test platform that offers comparable system features and capabilities found in proprietary ATE systems. Available as a bench top system or with an integrated manipulator, the TS-960e takes full advantage of the PXI architecture to achieve a cost-effective and full-featured test solution for device, SoC and SiP test applications.
-
Product
Battery Internal Resistance Tester
TOB-R-203
-
Xiamen Tob New Energy Technology Co., Ltd
Battery internal resistance tester used for lithium battery, lead-acid battery, Ni-Cd/Ni-MH battery and all kinds of batteries.
-
Product
Battery Discharger & Capacity Tester
IDCE-CT
-
Fuzhou Fuguang Electronics Co., Ltd.
Each wireless module can monitor 4 batteries simultaneously comparing with the traditional method that each module only canmonitor 1 battery, the new wiring operation become easier because the quantity of new modules needed is only a quarter of old-fashioned modules.
-
Product
Battery Discharge Capacity Tester
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
Product
Battery Powered Telemetry Systems
-
Advanced Telemetrics International
ATi’s Battery Powered Telemetry Systems are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
Product
Battery Chargers
BAC Series
-
Battery charger BAC series is a portable and universal battery charging solution. It is primarily intended for charging Lead-Acid, Ni-Cd and Li-ion batteries from 1 V DC to 300V DC level. However, the unit can charge the string of any battery type by one of the available charge modes:IU (constant current + constant voltage)UU (constant voltage + constant voltage with a current limit)Charging modes provide a safe regulation of charging procedure and achieves fast recharge and low risk of overcharge.Variety of implemented protections, such as thermal, overcurrent, undervoltage, and overvoltage, assure the charging process will be safe for the battery and the instrument itself.A user doesn’t have to switch off the main charger in order to use BAC series charger. Just the opposite, the BAC series charger should support the main charger to speed up the process. An alternative use is to quickly recharge a battery following a discharge test.The provided display enables users to monitor all relevant information during the charging process and to adjust charging parameters and limits in real-time.The instrument offers the best power-to-weight ratio in the market, weighing only 10 kg / 22 lbs with the maximum output power of 2,7 kW.The maximum charging currents for lead-acid, Ni-Cd and Li-ion batteries, at various battery voltages, are presented in the brochure.
-
Product
Battery Discharger & Capacity Tester
IDCE-2415CT
-
Fuzhou Fuguang Electronics Co., Ltd.
IDCE-2415CT Battery Discharger & Capacity Tester
-
Product
Battery Testers
-
Wuxi IMHOO Technology Co., Ltd.
Voltage of batteryBattery type1.5VButton Cell, AA,AAA,C,D,N3V Lithium6V Camera Battery9V 12V 15V 22.5V Power Source Not use batteryWeight 260gmeasurement 100x63x33mmPacking50pcs/CTN
-
Product
Lead-acid Storage Battery Analyzer
-
From the beginning of 2006 the verification of measurements of the analyzer of lead-acid chemical sources developed by Company "Megaron" is spent in Test laboratory "Neva-Reglament". The analyzer is intended for the express-estimation of a condition of lead-acid batteries: before the first use of new battery (an estimation of the electric characteristics declared by the manufacturer); during the battery operation (an estimation of a condition and working capacity at real application).
