Filter Results By:
Products
Applications
Manufacturers
BGA
Surface mount chip package, which uses solder balls for its connectors.
-
product
GHz Elastomer Sockets
Ironwood’s GHz BGA & QFN/MLF sockets are ideal for prototyping and testing almost any BGA or QFN device application. These ZIF sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss up to >40GHz and supports BGA or QFN/MLF pitches down to 0.3mm was utilized in these sockets. GHz BGA sockets are mechanically mounted over a target system’s BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry’s smallest footprint). They support IC devices with body sizes ranging from 55mm down to 1mm. Larger body sizes may require a backing plate. If the backside of the target PCB contains capacitors and resistors, a custom insulation plate with cavities cut for those components can be designed. This insulation plate sandwiches between the backing plate and target PCB.
-
product
DDR5 X4/x8 78-ball BGA Interposer For Use With U4164A Logic Analyzers
W5643A
The W5643A DDR5 2-wing BGA interposer for DDR5 x4/x8 BGA DRAM probing takes full advantage of the quad sample state mode on the U4164A. The W5643A is the smallest BGA interposers for DDR5 x4/x8 DRAM capable of capturing simultaneous read and write traffic at data rates exceeding up to 5GT/s for protocol analysis and up to 4Gb/s for DQ capture. U4208A and U4209A probe/cables connect any W5643A DDR5 BGA interposer directly into the U4164A logic analyzer module using 61-pin high density zero insertion force (ZIF) connectors that attach to the W5643A BGA interposer wings.
-
product
Digital In-Circuit tester
MTS180/300
Analog in-circuit inspection and function inspection are realized on this inspection equipment. IC pin float function is standard equipment. The MTS180 is a press type jig, and the MTS300 is a vacuum type jig. In the board mounting process at the production site, electrical inspection is performed on the mounted board after component mounting, and non-defective or defective products are automatically judged. The main inspection contents are short / open inspection, analog inspection of resistors, capacitors, coils, diodes, etc., lead floating voltage measurement of QFP and BGA, Digital IC inspection, frequency measurement.
-
product
DDR4 X16 2-wing BGA Interposer For Logic Analyzers, Connects To 61-pin ZIF
W4641A
The W4641A DDR4 2-wing BGA interposer for DDR4 x16 BGA DRAM probing takes full advantage of the quad sample state mode on the U4164A the W4641A is the smallest BGA interposers for DDR4 x16 DRAM capable of capturing simultaneous read and write traffic at data rates exceeding 3.2 Gb/s. U4208A and U4209A probe/cables connect any W4640A Series DDR4 BGA interposer directly into the U4164A logic analyzer module from 61-pin high density zero insertion force (ZIF) connectors that attach to the W4640A Series BGA interposer wings.
-
product
X-ray Inspection System
NEO-690Z / NEO-890Z
Off-line Microfocus X-ray Inspection System equipped with PONY ORIGINAL Direct Conversion X-ray Camera; SID-A50. Suitable for inspection of BGA, CSP, and LGA on PCB.
-
product
BGA Interposer, LPDDR4 200-ball, 2-wing For Logic Analyzer, Connects To 61-pin ZIF
W6601A
The W6601A LPDDR4 2-wing BGA interposer for LPDDR4 200-ball BGA DRAM probing takes full advantage of the quad sample state mode on the U4164A logic analyzer module it is compatible with. The W6601A is the smallest BGA interposer for LPDDR4 200-ball DRAM capable of capturing simultaneous read and write traffic at data rates in excess of 3.2 Gb/s. U4208A and U4209A probe/cables connect W6601A LPDDR4 BGA interposer directly into the U4164A logic analyzer module from 61-pin high density zero insertion force (ZIF) connectors that attach to the W6601A BGA interposer wings. Refer to the W6601A data sheet for complete list of LPDDR4 signals probed with the W6601A.
-
product
Low Power FPGA Featuring Hardened MIPI D-PHY, LVDS, SLVS, SubLVDS, & Open LDI Bridging
CrossLink
*Two 4-lane MIPI D-PHY transceivers at 6 Gbps per PHY*15 programmable source synchronous I/O pairs for camera and display interfacing*Available in amazingly small 2.46 mm x 2.46 mm WLCSP packages and BGA packages with 0.4 mm, 0.5 mm and 0.65 mm pitch
-
product
Signal Integrity Evaluation up to 50 GHz
N5225BT
The N5225BT provides the N5225B 50 GHz PNA, application software including PLTS and Enhanced TDR and accessories for signal integrity evaluation of cables, backplanes, and BGA packages.
-
product
PMC Module
PMC-CycloneII-64LVTTL
User Programmable Altera Cyclone II FPGA 672 BGA, EP2C35, EP2C50, EP2C70, Stand alone possibility, Single wide PMC Module, 64 LVTL, Optional User clock oscillator
-
product
Solid Measuring Viewer
SMV system is designed to perform automatic final inspecting system. SMV integrates professional vision and optics technology. Besides, reliable mechanical system reduces the maintenance time. It is especially suitable for the demand for high quality and low cost inspection. Unique inspection techniques adapt to all 3D measuring. It can detect laser Via, dimple, bump, copper plating thickness, line, SMT, BGA, etc. SMV provides 3D image and 3D measuring result. SMV adopts programmable LED lighting to obtain the best image.
-
product
BGA Rework Station
PDR IR-D3 Discovery
The system is tool free, gas free, instantly/precisely controllable, clean, modular, upgradeable and produces 100% yield BGA rework without any complications. It provides the extremely high levels of profiling and process control necessary for the effective rework of even the most advanced packages, including SMDs, BGAs, CSPs, QFNs, Flipchips and is ready for 0201 and lead-free applications.
-
product
Semiconductor Memory Tester
T5851
Advantest Corporation has introduced the T5851 system, designed to provide a cost-effective test solution for high-performance universal flash storage (UFS) devices and PCIe BGA solid-state drives (SSDs) memory ICs in high demand by makers of low-power, mobile applications such as smart phones, tablets and ultra-portable laptops. The flexible T5851 tester is available in both production and engineering models. This allows the system to be used for reliability and qualification testing as well as test-program development or, when equipped with an automated component handler such as Advantest''''s M6242, high-volume production. As a fully integrated, system-level test solution, the T5851 provides multi-protocol support in one tool while its tester-per-DUT architecture and proprietary hardware accelerator allow it to achieve industry-leading test times.
-
product
BGA Sockets
Our BGA socket platform takes advantage of the H-Pin®, a high-performance stamped spring probe pin, to provide a pure vertical contact system that meets all BGA design challenges at an enabling cost.
-
product
High-Throughput Film Frame Handler
MCT FH-1200
FH-1200™ film frame test handler is designed to handle leadless devices mounted on film frame, such as QFN, DFN, WLCSP, BGA, µBGA and eWLB packages. The FH-1200 enables high parallelism testing of post-saw IC devices at ambient temperature. It can accommodate 200 mm and 300 mm wafer rings and custom shapes onto which multiple strips can be mounted. No change kits are required regardless of package size (if same frame is used).
-
product
Automatic Test System
Star-Rec
Test entire HDI panel at once, or step & repeat in the "feed" direction. Fastest BGA Strip test system available. Star-Rec comes standard with: * loader * board cleaner * CCD Camera Alignment * electrical test section * fail and pass re-stackers * Board Marker
-
product
Near Zero Footprint SMT Spring Pin Sockets
Ironwood Electronics socket is a device size or near device size footprint test socket incorporating industry standard high performance spring pins. Ironwood can design a socket to work with any type IC packages- BGA, LGA, QFN, DFN and even leaded devices where you need to fit a socket in place of your device to allow fast, easy testing and development.
-
product
Semiconductor Package Inspection System
NIDEC-READ GATS (Grid Array Testing System) series carry out open/leak circuit tests on semiconductor package (MCM/CSP/BGA).
-
product
DDR4 BGA Interposers, DDR4 DRAM X16 Packages
N2115A
The N2115A DDR4 BGA Interposers are soldered in between the DRAM and PC board or DIMM raw card where the DRAM would normally be soldered. They are designed with the PCB or DIMM foot print on the bottom side and the DRAM footprint on the top side. The signals from the memory controller chip and DRAM are then passed directly to the top side of the BGA probe adapter where they can be accessed with the oscilloscope probes.
-
product
X-ray Inspection System
RTX-113HV
Precision X-ray Inspection for BGAs, QFNs, LEDs, sensors, medical devices, and other packaged devices.
-
product
11th Gen Intel® Core™ I5-Based Fanless Embedded Computer
EMP-510 Series
- 11th Gen Intel® Core™ i5 BGA SoC processor- DDR4 SODIMM up to 64GB- FHD/4K/8K up to 4x independent displays- 2x GbE, 1x COM, 4x USB ports- M.2 2280 SSD- Wi-Fi 6/LTE compatibility
-
product
Buffered Analog Crosspoint Switches
Analog Devices buffered video crosspoint switches offer multiple configurations from 8x8 up to 32x32 channels with gain of 1 or 2 and are offered in LQFP, LFCSP, and BGA packages. These crosspoint switches can be programmed either in serial or parallel modes and are used primarily for routing high speed signals, including composite video (NTSC, PAL, SECAM) and component video (YUV, RGB) in applications such as studios, video on demand, in-flight entertainment, surveillance, and video teleconferencing.
-
product
Computer-On-Module
Open Standard Module (OSM)
OSM form factor is the first computer-on-module form factor for solderable BGA mini modules that is natively capable of supporting both ARM and x86 designs. OSM modules are significantly smaller than previously available modules, with the largest measuring 45mm x 45mm. For a growing number of IoT applications this standard helps to combine the advantages of modular embedded computing with increasing requirements regarding cost, foot print and interfaces. The BGA design makes it possible to implement more interfaces on a small footprint. The largest Size-L (Large) measures 45mm x 45mm with 662 BGA pins. The modules are completely machine processible during soldering, assembly and testing.
-
product
Labelling Systems
8000BL
The Model 8000BL is a high volume labelling system for tray-borne devices. Equipped with tray stackers and a Zebra 90XiII label printer, the 8000BL can apply labels safely, accurately and quickly to BGAs, QFPs, TSOPs, PGAs, etc.
-
product
Industrial IP69K Stainless Steel Panel PCs With 11th Gen Intel® Core™ Processor
Titan2
- 11th Gen Intel® Core™ i5/i3 BGA type processor- 15.6”/21.5”/23.8” FHD with projected capacitive touchscreen- Full IP69K rating for dust and water ingress- Corrosion-resistant 304 stainless steel enclosure (316 for Option)- All M12 type connectors suite for harsh environments- Optional for optical bonding and high brightness (1000 nits)- Standard VESA, Yoke/Pipe mount (optional)
-
product
Boundary-Scan Interactive Analyzer & Toolkit
ScanExpress JTAG Debugger
Test probe access is a luxury—modern electronic system design techniques such as blind and buried vias or ball-grid-array (BGA) devices guarantee limited signal access. Test points quickly reduce precious board real-estate and can even degrade performance. ScanExpress JTAG Debugger overcomes these limitations to provide the control and visibility necessary to quickly debug and test hardware, using a simple JTAG port to interface with IEEE-1149.1 compliant devices.Whether debugging prototype hardware, enhancing production tests with boundary-scan control, or diagnosing a faulty board in the field, ScanExpress Debugger’s easy-to-use and versatile interface helps engineers test and debug systems faster and more efficiently.
-
product
Flexible Pick & Place Machine W/ 64-feeder Capacity
MC400
The MC400 Pick and Place machine places an enormous range of components, quickly and accurately, from 0201s through 100 x 150 mm SMDs, including BGAs, MBGAs, CSPs, µBGAs, MLFs, flip chips, odd form components and ultra-fine-pitch parts down to 15 mil. The system is easy to program and operate and comes standard with universal CAD conversion and teach-in capability.
-
product
Ultra High Speed Pick & Place
MC889
The MC889 is specially designed for the fast and highly precise loading of large batch sizes. This pick and place machine is equipped with an optical centering, "Vision on the Fly" system that guarantees the best possible measurement of SMD components (such as 0201, SOIC, PLCC, BGA, µBGA, CSP & QFP, as well as odd-shaped components) while completing placement at rates of 20,000 CPH.
-
product
BGA Rework Station
PDR IR-E6 Evolution
The PDR IR-E6 SMT/BGA rework system, using PDR’s patented Focused IR technology, has been specifically designed to cope with the challenges of repairing today’s Large PCB assemblies.
-
product
Low-power, High-performance FPGA
iCE40 LP/HX
*Available in three series with LUTs ranging from 384 to 7680: Low power (LP) and high performance (HX)*Integrated hard I2C and SPI cores that enable flexible device configuration through SPI*Match your preferred display to your application processor with interfaces such as RGB, 7:1 LVDS and MIPI DPI/DBI*Multi-source your image sensors by implementing flexible bridges supporting common interfaces such as HiSPi, subLVDS, LVDS and Parallel LVCMOS*Up to 128 kbits sysMEM™ Embedded Block RAM*Industry’s broadest range of 0.35 mm - 0.40 mm pitch BGAs fit in space-constrained applications
-
product
X-ray Inspection System
RTX-113™
Glenbrook’s RTX-113 is designed for heavy production environments where X-ray is used to inspect PCBs and assembled PCBs containing advanced components such as BGA, micro BGA, QFN and other devices.
