Filter Results By:
Products
Applications
Manufacturers
-
product
Relay Output Board
VME-2232A
VME-2232A is a 32-Channel Relay Output Board with Built-in-Test (BIT). Software compatible with the VMIVME-2232 and the VMIVME-2533.
-
product
Multipurpose Debug Board
DB40 Debug Module
The DB40 Debug Card is designed for debugging of COM Express and PC/104 boards. It includes the following features: - Port 80/81 decoding for Power On Self Test (POST) via LPC - Interface to SPI Flash for BIOS update - Interface to Board Management Controller (BMC) for update - Power and Reset buttons and status LEDs The DB40 Debug card can only be used on products that have the appropriate FFC debug connector designed for this purpose. (Includes DB40 Debug Module, two 40-pin FFC cables, and 14-pin cable for SP100 DediProg USB to SPI programmer.)
-
product
High Parallel Tri-Temp Pick-and-Place Handler
Delta MATRiX
Cohu’s MATRiX handler has a highly flexible test site configuration that’s well suited for a wide range of test applications, including analog ICs with short test times and high throughput, automotive devices requiring accurate thermal control, small pitch wireless-communication products, high parallel microcontroller testing, MEMS device testing, and many other device market segments with their unique requirements. The MATRiX has a highly flexible test site configuration that enables customers to reuse existing load-boards, including boards made for competitor’s legacy handlers.
-
product
Vibration Testing Equipment
Wewon Environmental Chambers Co, Ltd.
In Wewon, We have 2 powerful Vibration Testing Equipment. The Vibration Testing Equipment A is : EV210H0808VCSusb-E; The Vibration Testing Equipment B is: EV232H0809VCSusb-E. Technical parameters as below blank forms mentioned, The mainly difference is Sine Excitation Force, Frequency Range, Vibration Table’s size. Application for Vibration Test Equipment : The vibration test is to inspire or impact a part or device to see how it reacts in a real environment. The application of vibration test is very extensive, from the circuit board, aircraft, ships, rockets, missiles, automobiles and household appliances and other industrial products.
-
product
Diagnostic Solution
SYSTEM 8 Diagnostic Solution
The SYSTEM 8 Diagnostic Solution is the solution to board fault-finding problems. Equally at home with analogue and digital PCBs, the systems 64 digital and 24 analogue test channels provide a variety of test and measurement techniques to track down the most elusive faults.
-
product
High-Performance Integrated Functional Test Platform
Spectrum-9100™
The Spectrum-9100 is a fully integrated functional test system for factory, depot, and intermediate test applications. It’s the “go to” tester for users needing a mix of digital, analog, mixed-signal, and bus test capabilities across a wide range of products—from legacy boards to advanced systems.
-
product
PCB repair / rework station
XJInvestigator
Much more than a production line test tool, XJInvestigator is a repair focused, integrated test and debug environment for fault analysis, helping you efficiently recover your failing boards.
-
product
Burn-In Board Tester
Focus-275
Focus275 is a tester for burn-in board.It can improve reliability of burn-in board by inspecting boards for burn-in test by Focus275 regularlyBoth short open test and component test can be done by sending electric signals for special socket contactor and edge part.
-
product
EOS Tester
KT-200SG
This test instrument stands for the EMI(Electro Magnetic Immunity) ability test to the electric devices, electronic circuit boards & electric equipments. Recently this instrument is widly used in many companies in Korea & other countries to test the immunity to thier products-power supply, drive PCBs, communication systems, LCD display panels whether they are safe or not against the impulse & noise.All for the purpose, of this object, it generates 4 ~ 5 kinds of different impulse test waveforms.Output test voltage level : 5 ~ 200 V ImpulseOutput voltage polarity : Positive, NegativeType of waveforms
-
product
Custom Pogo Pin Rings & Blocks
Reduce your cost-of-test with our pogo pin blocks and interfaces that transform complex DUT boards or breakout boards into universal motherboard-style interfaces. Eliminate the need to purchase or build a new board for every unique device, unit, or package.
-
product
Fault Diagnostics in Power-Off State
QT55
Qmax Test Technologies Pvt. Ltd.
Signature Method of Testing is also known as VI Trace Characteristics, is a proven fault diagnostics technique in Power-Off state while testing a board. By applying known wave from signal with desired Voltage, Source impedance and Frequency of the stimulus signals, depending upon the test node and its characteristics, a Voltage (V) vs Current (I) graph is plotted and studied.
-
product
Protocols
Excalibur Systems provides a large selection of board level products for test & simulation, as well as, the embedded environment. Choose from a number of avionic protocols under platforms such as, USB/Ethernet, PC/104, PMC, PCI, Compact PCI, VME and VXI.
-
product
System Level Test and Burn-in Solutions
System Level Test (SLT) is a paradigm shift from traditional structural and functional testing. The device is tested in a complete, integrated system to evaluate its compliance against specified requirements. The system approach allows for higher and more cost-effective test coverage especially for multi-function and non-deterministic devices. It also brings new integration and test challenges like: ..Designing test fixtures on Burn-in Boards with system components ...
-
product
Boundary Scan Test
Boundary Scan is a very useful tool for quick, low-cost, re-usable powered-up test of an assembly for basic functionality. Because a fixture with test probes is not required, it is possible to have a working test available within hours or days, rather than weeks. Designers can receive rapid feedback on their prototype boards with tests that can be used again during production testing, as well as for device programming. Given power, ground and Tap port signals, tests can be written to assess the performance of the boundary scan enabled parts on an assembly and other parts on the boundary scan chain.
-
product
Fastest In-Circuit Test Platform
TestStation
Teradyne’s TestStation in-circuit test systems provide electronics manufacturers with reliable high-quality, high-volume testing for the latest printed circuit board assembly (PCBA) technologies that are used in automotive, industrial, computing, consumer, communications, and defense end-products.
-
product
Vacuum Test Fixtures
Series 63
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
-
product
Digital/Pattern/PE Card
PEMU32
The PEMU32 represents a new level of MULTIFUNCTION for PXI-based instrumentation. Based on the proven architecture of the PE32, the PEMU32 offers high voltage PMU/DPS and pin electronics in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 256 bi-directional pins (8 boards). The PEMU32 also supports deep pattern memory by offering 32 M of on-board vector memory with dynamic per pin direction control and with test rates up to 10 MHz.
-
product
Wireless Functional Test Fixtures
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
product
PCI Express Gen 1 Test Backplane
SKU-015-01
The PCI Express Test Backplane was designed to support production testing/debugging of PCIe-based peripheral boards. The backplane expands the x1 PCI Express interface of the host computer into one x4 and three x1 PCI Express slots via 7 ft CAT6 cable.
-
product
FPGA Image Processing (IP) Development Kit
ProcVision
Gidel’s Vision Pro Development Kit is an optimal solution for developing,validating, demonstrating and evaluating Image Processing (IP) andpipeline designs on FPGA.The suite is designed to provide a complete and convenient envelop enablingthe developer to focus strictly on the proprietary image processingdesign. The entire Vision Pro flow is within a single FPGA, independentof the final target application(s). The Vision Pro flow is composedof a pipeline that streams simulated data to the user image processingdesign under test (DUT) and then captures the design’s output streamfor displaying, storing, analysis and/or co-processing on host software.The entire process is performed on a single FPGA without the need foradditional peripheral connectivity or tools.Vision Pro suite is plug-and-play enabling the developer to begin at oncethe IP design development and validation. A simple design example providesthe developer immediate hands-on familiarization with the systemflow and supporting tools. The final design can be ported to any IntelFPGA device or other vendors’ devices (FPGA or ASIC) by replacing basiclibraries. To significantly reduce compilation time, initial design developmentmay be on a small FPGA device and later compiled for the targetdevice(s). The target implementation may use any FPGA board. For a fullImaging/Vision system solution, Gidel offers a number of off-the-shelfgrabbers and FPGA accelerators that are designed to utilize these imageprocessing blocks and Gidel Imaging Library (GIL).
-
product
Automated Multi-Functional Tester
QTouch 1408 C
Qmax Test Technologies Pvt. Ltd.
QTouch 1408 C – Automated Multi-Functional Tester with in-built camera is designed to make automatic image capturing and probing of electrical signals with ease and speed especially in PCBs with high density/high pin count device that are mounted on the PCB. It is designed to move on X, Y, Z directions making it possible to probe every component as close as 20 mils. Easy tagging feature allows the user to get the real time XY coordinates using the library information with minimal intervention. CAD import feature is available for Auto Test Generation/to extract the XY coordinates from the CAD data. Qmax Automated Multi Functional Tester can perform Board level functional test of a PCB and guided probe / Back tracking diagnostics utility to reliably test Digital, Analog and Mixed Signal PCBs and fault isolation to the PCB level or component level.
-
product
Power Utility Industry
Major product types include:*Auxiliary and Tripping Relays*Test Blocks*Arc Flash Protection*Utility Grade Protection and Control Relays*Industrial Controls and Pilot Lamps*On Board Railway Relays, CB’s and Panel Meters
-
product
Cryogenic Millimeter-Wave / Microwave Test Fixtures and Calibration Kits
upj10
KEYCOM''s cryogenic millimeter-wave / microwave test fixtures and calibration kits are specifically optimized for testing the performance of patterns between the edges of printed boards(edge type) and circuit testing on the printed boards(probe type). They are also designed to minimize heat capacity by miniaturizing their dimensions so they cool off efficiently, and materials with low coefficient of linear thermal expansion such as invar are used for major parts where high dimensional stability is required. Their operating frequency ranges from DC to 110GHz.
-
product
Video Signal Generator
MSPG-2000
MSPG-2000 Video Signal Generator, was designed to test standard Panel and Multimedia Video Signal. Separated four(4) boards generate selected own(1) Time & Pattern and output to the each section with two(2) ports.
-
product
Test Hardware
Development of additional hardware components in-houseCreation of the layout of the developed circuit boards and subsequent production outside the companyAssembly of the printed circuit boardsCreation of additional circuits for test adapters
-
product
Test Board For SFP+ / SFP28 Transceiver
ESFP280
The OPTELLENT ESFP280 is a cost-effective and convenient test board for testing SFP/SFP+/SFP28 optical transceivers in R&D and manufacturing environments. The ESFP280 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The ESFP280 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
product
Engineering Services
In addition to the highest quality test programming, maximizing board coverage, and efficient board testing, TTCI offers a full array of other engineering services, including CCA (Circuit Card Assembly) Testing, Design for Test, ASTER TestWay electrical design for test analyzer, Feasa LED analyzer, SMH Technologies FlashRunner in-system programmer, finite element analysus, installation, reverse engineering of Gerber to CAD, Training, Test System PC, Hardware, and Software Upgrades, and more.
-
product
Connectors Specifications
Flex to Board
This revolutionary new ‘wiping’ action RC contact technology is a Patented Ardent Solution for ultra-small flex-to-board connectors and sockets. Ideal for both test and production use, SC™ connectors are available for custom applications with short lead times. Exceptional Signal Integrity Long Life Lower Component Costs Lower Overall Costs
-
product
Salt Spraying Test Chamber
Sanwood Environmental Chambers Co ., Ltd.
Sanwood is glad to be the ODM/OEM manufacturer of Salt Spraying Chamber,Salt Spray Test Chamber,salt spraying test chamber,Salt spraying chamber,Salt spraying chamber sales enterprises all over the world! 1：It adopts 5mm or 8mm imported gray and white impact resistant P.V.C board, with high temperature resistance up to 85℃ and corrosion resistance. 2：Support frame: ¢ 10MM fiberglass rod, corrosion resistant. The steel V-frame and the fiber rod angle are placed to ensure the specimen is inclined at 15-30 degrees. 3：Pressure barrel is welded seamlessly with 2.0MMSUS304 stainless steel plate 4：The heating adopts titanium alloy electric heating tube. It has high corrosion resistance and long service life is 3-5 years higher than ordinary stainless steel heating tube. 5：The cover is made of 5MM imported transparent (Germany YLIS) acrylic sheet. It has fine workmanship, beautiful appearance and high transparency.
-
product
4x IDC to 192 Pin Quadrapaddle
YAV90Q04
The interface YAV90Q04 permits to connect two YAV90096 boards to one 192-Signal contacts Quadrapaddle module. As the Mini-D 50 connectors let 2 free pins (1 and 26), these pins are interconnected to a test point, with the possibility of be grounded. Cable P/N J6200540: Mini-D-50 to Mini-D-50 IDC connectors with 400 mm flat cable.
