Filter Results By:
Products
Applications
Manufacturers
1553
Interface Standard for Digital Time Division Command/Response Multiplex Data Bus
See Also: Mil-Std-1553
-
product
Portable Bus Analyzer
1553
Our new inline Bus Monitor is a very small, very light MIL-STD 1553 Bus Monitor that can be connected to any Windows device with a USB connector. It monitors and records all or selected 1553 traffic for later analysis or reconstruction in the lab.
-
product
MIL-STD-1553 A / B Test And Simulation USB Module
USB-1553
*Dual redundant*1 or 2 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*More programmable triggers and acquisition*10 programmable I / O*Onboard IRIG-B timecode encoder / decoder*Supports stand-alone operation via USB connection, without external power supply*On-board battery for runtime without power supply
-
product
PCI Express Card
EXC-4000PCIe/xx
The EXC-4000PCIe/xx card for the PCI Express bus supports up to four dual redundant 1553 channels using the M4K1553Px(S) module and is compatible with all common variations of MIL-STD-1553 (A, B).
-
product
BusTools/1553 BusTools Software Analyzer
Abaco Systems' BusTools-1553 is an integrated, Microsoft Windows-based, application solution for MIL-STD-1553 test, analysis and simulation. BT-1553 software harnesses the power of Abaco Systems' hardware interfaces on PCI, PCI Express, CompactPCI, PMC, ExpressCard, PCMCIA, USB, XMC, PC/104-Plus, VME and VXI platforms for simplified control over simulation, display, data logging, playback, and protocol analysis of MIL-STD-1553/1760 A and B networks.
-
product
MIL-STD-1553 Fiber Optic Bus Extender
FO-1553
Avionics Interface Technologies
Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT
-
product
Record and Analyze Flight Data
TDS AND MRC
AMPOL's TDS and MRC-150 are complete legacy solutions that can record and analyze flight data from a number of sources. These solutions are especially useful in the air for flight-test and integration phases, as well as on the ground for pre-flight tests. The TDS is a complete solution for recording and analysis of telemetry data from multiple sources. Installed on a fighter jet's wingtip, in an air-to-air missile pod, the TDS's airborne unit is sealed and has a removable, solid-state Flash disk for storage of recorded data. The system can operate either autonomously, with no outside intervention, or manually, from the cockpit. The TDS solution also includes software for off-line data analysis at the ground station. The MRC-150 is a complete solution for recording and analysis of four MIL-STD-1553 buses and one H009 bus on-board an F-15 fighter jet. Installed in the aircraft's equipment bay, the MRC-150 can either be operated autonomously, with no outside intervention, or manually, via the cockpit. The MRC-150 has already been used in hundreds of flights since its debut in 1998.
-
product
Cable
RCONQPMC-4
RCONQPMC-4 - Transitions from a SCSI-68 pin connector to eight CJ70 Twinax, 3 lug, 1553 cable jack ends and one D-Sub 50 pin connector for additional I/O.
-
product
Mini PCI Card
EXC-1553mPCIe/P1
This card’s small size and suitability for Mini Card compatible computers make it a complete solution for developing, testing, integrating 1553 interfaces and for performing system simulation of the MIL-STD-1553 bus, both in the lab and in the field.
-
product
Multi-Protocol Board
EXC-4000VME/VXI
The board supports up to 8 modules, and each module represents an independent test and simulation device. Most modules are based on existing Excalibur products such as the 1553 Px family, the 1553 MCH family and the ARINC-429 RxTx. Additional modules are being added constantly.
-
product
Adapter
EXC-1553UNET/Px(S)
The EXC-1553UNET/Px is an intelligent, single - or - dual channel, MIL-STD-1553 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1553 bus, both in the lab and in the field.The EXC-1553UNET/Px shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.
-
product
VME Generic Carrier Card For PMC(PCIbus Mezzanine Card) Modules
AVC-2
VME64x (6U) generic carrier card for PMC (PCIbus mezzanine card) with 2 PMC slots. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
product
MIL-STD-1553 PMC Interface Module
PMC-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - 3.3v PMC (with 5V Tolerant I/O), 64-bit 33/66MHz - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
1 Channel, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTA
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
Multi-Channel 1553 Interface for PCI Express 4 Lane Systems
PCIE4L-1553
Alta Data Technologies’ PCIE4L-1553 interface module is a multi-channel (1-4), ½ size, 4 Lane PCI Express 1553 card supported by the latest software technologies. The PCI Express card is based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
product
Software
Alta may have the most advanced COTS MIL-STD-1553 and ARINC hardware devices, and our test and development software is 2nd to none. Alta's software is modular, portable, and made for real-time controls & test -- and designed for rapid integration success. This page provides a brief overview of each product and links to main landings pages.
-
product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 16-Channel, 2-Pole
40-739-002
The 40-739-002 (PXI) and 42-739-002 (PXIe) are dual 16-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
product
MIL-STD-1553 Four-Channel VME Board
BRD1553VME-4
The V-Orchestra™ is a four channel MIL-STD-1553B board, which includes Bus Controller (BC), Remote Terminal (RT) and Monitor (MT) capability for each channel. V-Orchestra channels are software compatible to DDC® Enhanced Mini-ACE® components and architecture, with 64K word of internal RAM.
-
product
PCI-Express Generic Carrier Card
ACPe-1
PCI-Express generic carrier card for PMC (PCIbus mezzanine card) modules with 1 PMC slot. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
-
product
Interface Card - 1-2 Channels of MIL-STD-1553 Networks on a PMC Form Factor with Ethernet Backplane Interface
PMCE-1553
PMCE-1553™ is an innovative product that provides 1553 operations via 10/100/1000 Ethernet IP/UDP local area networks (LAN) backplane. PMCE-1553 is a standard PMC form factor card, but instead of PCI backplane, PMCE-1553 uses the P4 connector for Ethernet based control and communications.
-
product
4 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTF
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
USB 2.0 SmartCable For MIL-STD-1553 Test And Simulation
ASC1553
The ASC1553 (AIM SmartCable) USB module offers full function test, simulation, monitoring and recording for MIL-STD-1553B applications implemented in an ultra compact form factor.
-
product
MIL-STD-1553 Products
- Wide Selection of MIL-STD-1553 COTS Interface Cards/Boards and Real-Time Appliances- Packetizing Engine – 3rd Gen Design Common Data Packet (CDP) Architecture- Portable FPGA AltaCore Design – Reduced Parts Obsolescence Risk
-
product
Mini Munitions Store Interface
MMSI
Mini Munitions Store Interface (MMSI) (EBR 1553) modules support up to 8 MMSI hub ports and composite Bus Monitor output using the M4KMMSI module. Each module can operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT/Concurrent Monitor, and Bus Monitor.
-
product
Portable Interface Unit
1553-USB-PIU
The 1553-USB-PIU is a Portable Interface Unit providing full MIL-STD-1553 test, simulation and bus analysis capability in a compact self-contained unit, to connect via a USB interface to suitable host systems. The unit provides support for all 1553A, 1553B, McAir and STANAG 3838 variants in a self contained battery operated unit, and is supplied with a matching power supply and battery charger unit for desk-top use. The 1553-USB-PIU supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The unit is supplied with "C" Driver library, together with a Windows GUI, providing a user friendly software tool for all 1553 set-ups, data management and storage.
-
product
IRIG 106 Chapter 10 SDK for MIL-STD-1553 Applications
Avionics Interface Technologies — A Teradyne Company LOGIN Open Search Form F-SIM-1553-AVOE F-SIM-1553-AVOE
Avionics Interface Technologies
Supports Capture, Recording, & Analysis of MIL-STD-1553 Chapter 10 Ethernet Data Streams - View Live MIL-STD-1553 Data and Activity Statistics from one or more Chapter 10 Streams - Compatible with AIT eDAQ-1553 & eDAQ-1553-FQ Modules - Open, View, Save, & Analyze MIL-STD-1553 bus data from Chapter 10 Archive Files - Replay MIL-STD-1553 bus data from Chapter 10 Archives using any of AIT’s MIL-STD-1553 Interface modules - Supported in AIT’s Flight Simulyzer simulation and analyzer software application
-
product
Avionics/Vehicles Bus, Serial I/O, Shared Memory, and More
Curtiss-Wright Defense Solutions
Curtiss-Wright offers a wide range of solutions for high-speed, low latency communications and shared memory products. These products are offered in a variety of form-factors including PMC, XMC, PCIe and PC/104 cards designed to support popular communications standards including 1553, ARINC 429, CANbus and Serial FPDP.
-
product
Single or Dual Stream MIL-STD-1553A/B Test and Simulation Modules
AXC1553-xT
MIL-STD-1553 Test and Simulation modules for XMC with 1 or 2 dual redundant streams plus 8 Discrete I/O’s (on Rear-I/O).*Concurrent BC, MRT (31) and Chronological/Mailbox Bus Monitor*Full Error Injection/Detection (AS4112)*Complex Triggering, Data Capture/Filtering & 100% Bus Recording*Physical Bus Replay*IRIG-B Time Encoder/Decoder*Programmable Bus Coupling, onboard Bus Network and variable Output amplitude*Full Function, Single Function and Simulator Only versions available*Drivers for Linux and Windows*Optional Databus Test and Analysis Software and RT Production Test Plan
-
product
Vegas Data Diode
01-09838
Non-ruggedized module that addresses concerns regarding use of untrusted, commercial-off-the-shelf (COTS) bus logging on aircraft with a MIL-STD-1553 or ARINC-429 bus interface.
-
product
18" Cable
CONV1553-3
An 18" cable assembly transitions from individual IP Module ribbon connectors on: VME and VXI front panels (or internal VME-AIC connectors) to two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends.
