BER Test
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received.
See Also: BER Testers
-
Product
Measurements & Material Testing
-
MAGNET-PHYSIK Dr. Steingroever GmbH
, we can offer measurement tests and material tests of all kinds on hard and soft magnetic materials. It is also possible to carry out measurements on site. We carry out stray field measurements on your magnetization station in production in accordance with the professional association regulations (BGV). We also carry out magnetic field measurements on air freight goods in accordance with IATA 953.
-
Product
Nanomechanical Test Instruments
-
Bruker has developed a comprehensive suite of nanomechanical and nanotribological test instruments that operate in conjunction with powerful microscopy techniques. Combining the advantages of advanced microscopy technologies with quantitative in-situ nanomechanical characterization enables an accelerated understanding of material behavior at the nanoscale.
-
Product
Web Application Testing
-
UpDoer offers comprehensive, scalable testing solutions for critical web application projects through its unique business model. We understand the complex nature of such apps, whether they are created for enterprise users or mobile applications tailored to Android or iOS-based devices.
-
Product
Communication Test Set
Eye-BERT 100G
-
The Eye-BERT 100G is a low cost, full-featured, stand-alone communication test set with an integrated post equalizer eye opening monitor / scanner. Ultimate flexibility is provided with three different physical interfaces, 13 different configurations, and configurable transmit and receive clocks. The tester supports PRBS patterns up to 263-1 and select data rates from 1.25 to 29Gbps on up to 4 simultaneous channels. Front panel controls are also provided for stand-alone operation. Unlike competing products, fast post equalizer eye monitoring and scanning is included and can be performed on any input channel above 5Gbps.
-
Product
Mechanical Testing
-
The Mechanical Testing Department at IMR is well equipped to perform most standard mechanical testing, as well as specialized tests designed to the customer's requirements. A complete in-house machine shop supports the department with precise specimen preparation and fixture fabrication.
-
Product
USB Test Hardware
-
Test stations with USB hardwareHardware control of adapters with USB-I / OFlash and microprocessor programmer
-
Product
Benchtop Test Chambers
MicroClimate
-
The MicroClimate 1.2 cubic foot benchtop test chamber is capable of simulating a full range of temperature and humidity conditions. This environmental testing chamber is designed to provide users with a compact unit for testing small components and products.
-
Product
Flammability Test Chamber
-
Shenzhen Bonad Instrument Co., Ltd.
BONAD’s flammability test chamber complies with IEC 60950, IEC 60695, IEC 60112, IEC 60332 and other standards. We not only provide standard wire and cable combustion test equipment and leakage tracking test equipment and other electrical test equipment as well as a variety of different combustion test equipment, but we also provide customization and can develop professional and high-quality test equipment according to test requirements. For more information, please contact us, BONAD will provide you with professional technical advice and high-quality testing equipment.
-
Product
Conformance Testing
Clarinet-TTCN ATM ETS
-
Protocol: UNI 3.1 ATM Layer Conformance Test Suite for End SystemsIUT: ATM Equipment UNI 3.0ATS: ATM-FORUM standards af-test-0060.000 covers the test of UNI 3.0 ATM Layer of End Systems
-
Product
Sensors And MEMS Test
-
Easy docking and undocking of the MEMS modules to the standard test handler whether Gravity, Pick and Place or Test in StripTest in the complete tri-temp range for ambient, hot and cold (automotive certified)Easily convertible to other packagesDownscaled stand-alone engineering set-up availableGlobal support by experienced Cohu Field Service and Applications staff
-
Product
Accessories: Test Hardware
-
Copernicus Technology supply test hardware accessories to support Intermittent Fault Detection testing using VIFD™ and IFDIS™ test equipment, such as Interface Test Adapters (ITA). We also supply and repair general purpose and customer-spec test hardware accessories: ITAs, Break-Out Boxes (shown below) and Mobile Vibration Systems. The Mobile Vibration System can be quickly set up in repair bays for applying environmental stimulus to components and wiring harnesses during testing.
-
Product
Surveying Test Equipment
-
Our range of surveying test equipment offers a useful range if instruments, including Laser Distance, Boroscopes, Moisture and Gas Filled Lamp testers.
-
Product
Test Chambers
-
Used to simulate the operating conditions necessary for accurate testing of depth gauges used in various military and commercial applications.
-
Product
Edge/Wireless Test Services
-
Austin Labs offers consultancy and interoperability services to help in all stages of product development, from specification to market launch and beyond. Our global dedicated test labs for Bluetooth, WI-FI, USB and Phone Projection technologies (Apple CarPlay and Android Auto) help you minimize field issues, lower development costs, and speed your time to market with products that you can feel confident will deliver a superior user experience.
-
Product
Electrostatic Discharge Testing
-
MET Labs offers special ESD testing services at controlled temperature and humidity, in a specially-designed and dedicated chamber.The chamber consists of ESD waveform verification setup and tables that accommodate a variety of EUTs. The chamber has a capability to vary the relative humidity from 15% to 65% and temperature from 18°C to 24°C.
-
Product
VG Test Panel
TA-300
-
This panel has many additional features that also allow testing of the VG-206 series gyros. Dedicated API connectors are provided for both pitch and roll outputs. This Panel includes a TA-900 API. This panel is designed to allow by the book testing.
-
Product
Cogging Test System
CTS
-
Magtrol’s Cogging Test System is a stand-alone test system designed to control and measure Detent Torque, Cogging Torque and Friction Torque. The test System includes a precision geared motor, a TS Series Torque Sensor integrating a 5 000 pulses encoder. CTS 100 to CTS 102 have a built-in security clutches to avoid system overload by mishandling when not in use. The geared motor drives the MUT (Motor Under Test) at a low speed from 1 to 10 rpm (respectively 8 rpm for CTS 103 and CTS 104), while acquiring its cogging torque related to angle position.
-
Product
IPX9K Rain Spray Testing Chamber / Rain Resistant Test Machine
CX-IP9K
-
Shenzhen Chuangxin Instruments Co., Ltd.
Water Spray Test Equipment is used to test the water resistance; which is mainly for electronic and electrical products. It can also provide references for product design and quality control.
-
Product
Sand & Dust Test
-
This test method is divided into two procedures. The small particle procedure, using fine dust is performed to ascertain the ability of equipment to resist the effects of fine particles which may penetrate into cracks, crevices, bearings, and joints. The blowing sand test, using coarse particles, is performed to determine whether equipment can be stored and operated under blowing sand conditions without experiencing degradation of its performance, effectiveness, reliability, and maintainability due to the abrasion or clogging effect of large, sharp-edged particles.
-
Product
Chloride Test System
C-CL-2000
-
The C-CL-2000 produces results on-site, within minutes that are accurate and comparable to expensive laboratory tests. It measures the electrochemical reaction of a weighted sample placed in an extraction liquid. It automatically shows a temperature compensated reading of percent of chlorides on its digital display. A wide range - from 0.002 to 2% chloride by weight - is covered.
-
Product
Transformer Test Equipment
-
DV Power test instruments perform various diagnostic tests on power and instrument transformers. Even more, a unique feature is a condition assessment of on-load tap changers. Performing a transformer test before their breakage can be crucial.Test instruments are portable and enclosed in durable metal cases. Also, the 19” rack-mounted version suitable for factories is available as well.Applications supported by DV Power transformer test equipment include:Winding resistance measurement (IEC 60076-1)Analysis of on-load tap changers (IEC 60214-1)Heat run test (IEC 60076-2)Automatic transformer demagnetizationTurns ratio measurement of power and instrument transformers (IEC 60076-1)Excitation current measurementPhase angle measurementTransformer vector group detectionDemagnetization status verificationAll of the above-mentioned measurements are performed with the highest accuracy.The advanced DV-Win PC software collects both numerical and graphical results. As a result of that, these features provide an easier and more efficient analysis. After the test, DV-Win software generates a test report with a single click. Furthermore, a user can easily customize the test report and save it in different formats, such as XLS or PDF.Finally, the analysis of on-load tap changers is performed by the new method called dynamic resistance measurement (DRM). This is a non-intrusive method. Therefore, it allows detecting problems in on-load tap changers without disassembling them.
-
Product
Automotive Test Systems
-
Ono Sokki Automotive Test Systems - flow meter, non-contact speedometer, engine tachometer, crank angle detector, and more
-
Product
Testing Software
-
SMC supplies as standard several types of software adapted to each set, for automatic testing, unit operation and reports or results acquisition, which allows the full functionality of the equipment; the following programs are included with the corresponding equipment:
-
Product
Test Equipment Calibration
-
EMC Technologies can provide convenient, local, NATA accredited calibration services which greatly reduces lead time and costs for EMC test equipment. In the past these items had to be sent overseas or to expensive government laboratories. We can calibrate these items against common standards such as CISPR 16 (and subparts), IEC 61000-6-X series, ANSI C63.4, ANSI C63.5 and ARP 958.
-
Product
Generate MC/DC Test
VectorCAST/MCDC™
-
Modified Condition / Decision Coverage (MC/DC) provides two levels of verification for conditional expressions. The first level, named MC/DC Branches, tracks each subcondition in an expression to verify that is has been tested with both True and False values. The second level, named Equivalence Pairs, verifies if each subcondition can affect the value of the condition. This is done by generating a truth table for the expression, and then finding a pair of rows in the table that will generate a different result when all values except the tested value remain constant.
-
Product
Functional Test Fixtures
-
Test Head Engineering's Custom Functional Test Fixtures range from simple to extremely complex. Typically, our customers do their own wiring and programming, but we will complete the job right up to the customer's requirements, including offering turn-key control and test programming through our partners.
-
Product
Magnetic Effects Test
-
This test determines if an object can operate normally in strong externally generated magnetic environments. The magnetic effect test helps to assist in determining the proper location of the equipment in the installation.
-
Product
Exacting Electric Motor Testing
-
The Taylor Dynamometer Electric Motor Test Stand is designed to provide maximum reliability, excellent durability and flawless performance. Using our extensive line of Water Brake engine dynamometers, Taylor Dynamometer has systems available for testing electric motors from 5 to 13,000 hp (3.7 to 9,694 kW). Include an instrumentation package to achieve your testing requirements. From simple speed, torque and power display systems with manual control to completely automated testing solutions, Taylor Dynamometer has a system to meet your testing requirements.
-
Product
Battery & Electrical System Testing
12-0200
-
Vehicle Battery Systems fitted to modern cars require a complex system to control and maintain the best charge and discharge rates which not only ensures the longest in service life but also that systems such as Stop/Start operate correctly. The 12-0200 gives the operator access to all the functions complicated and time-consuming manufacturer scan tools have to perform the same function but in a fraction of the time. On average the total time required by the technician to reset a system will be 30 seconds.
-
Product
Multi-Stage Functional Test Systems
-
Circuit Check’s bi-level and multi-stage fixtures combine multiple test levels in a single fixture using controlled actuation and selected probe travels for powered and unpowered tests.
