Tech-Aid Products
Tech-Aid Products is a company which is dedicated to providing quality Avionics And Instrument shop test equipment to the aviation community.
- (918) 838-8711
- (918) 835-2282
- Kim@techaidproducts.com
- 2708 N Sheridan Rd
Tulsa, Ok 74115
United States of America
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
Bi-Polar low voltage power supply board
LVPS
-
This is our standard power supply board used in many of our testers but also available separately. This board is capable of +/-15v, +10 and +5v outputs. Also contained on board is our standard meter drive circuitry for testing instrument meters, a two-pole relay and an option for a sine/cosine oscillator circuit.
-
Product
Channeling Decoder, Nav/Comm/Control Head
RCD200
-
Designed to provide the Avionics shop a simple and expeditious method for testing general aviation radio tuning. Provided are front panel mounted LED's as well as a digital display to provide the quickest code recognition while testing. With this simple method of testing you will soon find yourself testing all your radios and finding those troublesome intermittents. This unit also decodes altitude and ARC 1000 serial data. Click on picture for larger view.
-
Product
GAMA ARINC 429 Emulator
TA-429
-
ARINC 429 EMULATOR FOR GENERAL AVIATION (4th QTR) Unit will allow viewing multiple labels while receiving as well as when transmitting. Auto-increment when transmitting allows for more dynamic testing of equipment. All presented on a bright 4 line x 20 VFD.
-
Product
Digital Panel mounted OBI Display
TA903-01
-
This panel mounted or portable display can read the radio bus digital OBI format (Clk, Sync, Data Format) that typically drives RMI's. This format is even more widely employed with the advent of GPS/FMS and newer digital radios. This display will confirm the digital bearing accuracy of these radios.
-
Product
Customer Acceptance Test Panel
TA-65
-
DGS-65 Customer Acceptance Panel for both testing and trouble- shooting. We have added an option to the panel that allows you to select an analog slaving meter or the LED monitor lights as shown in the maintenance manual Fig. 5-14. The addition of the meter provides the technician with a more visible means to monitor the slaving "trend". The 50 pin DG connector is broken out on the panel to assist in monitoring or isolating unit signals.
-
Product
HDG and OBS Track Select Panel
TA-260
-
Universal Heading and Track Selector Panel This panel provides a synchro transmitter for Heading and a synchro resolver for Nav converter alignment. The synchros are mounted on industry standard 18:1 dual speed drives for maximum accuracy and repeatability. This unit can be used to calibrate both manual and automatic converters. This panel provides a rear mounted interface connector as well as front mounted tip jacks for independent breakout if so desired. The TA-260 also provides two discrete switches associated with the resolver configuration. The 30Hz/400Hz switch is provided to allow the resolver to be properly compensated for the type of Nav converter to be aligned. The second switch allows you to open or short the resolver rotor lead as may be required by some newer GPS equipment. This panel is lightweight enough for portable use or may be rack mounted.
-
Product
Becker Transponder Test Fixture
TA-3400
-
This transponder test fixture is specific to the requirements for testing Becker Avionics Transponders and provides interface connectors for both the panel mount and remote systems. The panel also provides switches to implement Gillham code altitude as well as separate interfaces for an external parallel or serial encoder. The panel will interface with the RMU 5000 or standard control head. This fixture also comes with voltage and current meters along with an internal dimming source. This panel comes in the standard 19 inch rack width and measures 12 inches in depth.
-
Product
Track Select Panel
TA-6
-
A universal master HDG/OBS selector panel with heading synchro transmitter, To/From meter and precision track selector. This panel requires a customer supplied RMI. Panel test jacks allow for external use of both the Hdg transmitter and precision resolver. This standard panel will allow by the book testing and mates directly with TA-5. Click on picture for larger view.
-
Product
Flux Valve Simulator
FV Sim
-
This flux valve simulator is designed around the synchro format and is employed in our TA-14 DG panel. This simulator is also available now in a portable enclosure for testing the Sperry or Jet Directional gyros.
-
Product
Adapter for 980L-1A Tester
TA-331A
-
331A-9G HSI Adapter for use with the 980L-1A tester. Built to manufacturer's specs to allow by the book testing.
-
Product
VG Test Panel
TA-300
-
This panel has many additional features that also allow testing of the VG-206 series gyros. Dedicated API connectors are provided for both pitch and roll outputs. This Panel includes a TA-900 API. This panel is designed to allow by the book testing.
-
Product
Test Panel
TA-5
-
A complete NAV/LOC/GS/MKR test panel designed around the VIR30/31/32 units. Requires channeling source. Combining the TA-6 panel provides a complete integrated system.
-
Product
Mach Airspeed Test Fixture
TA-6055A
-
The TA-6055A is a Mach Airspeed Test Fixture built to support the testing and repair of the 2082 and 2083 series of Servoed Mach Airspeed Indicators (SMASI) used in some Boeing aircraft. These mach airspeeds are synchro driven and require a coarse and fine input for altitude and a third input for airspeed. This test fixture was designed around the test procedure and is interfaced with our TA-1001 panel which provides for two of the synchro sources and two Angle Position Indicators (API).
-
Product
KX-155A Display Assembly Extender Card
KX155-EXT
-
The KX-155A Display Assembly Extender card will give the technician access to troubleshoot a display problem on this Bendix/King Nav/Comm. The card breaks out all pin connections with their functions silk-screened on the board. This board will allow the technician to make a more logical decision on what the problem may be. We have seen in our shop that the glass display is not always the failed componet.
