-
Product
Signal Amplifier
9100A
Amplifier
Model 9100A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
Product
Differential Active Probe, 250 MHz
DP0010A
Signal Probe
The Keysight DP0010A is the 250 MHz model of the DP001xA Series differential active probes. These probes provide the superior general-purpose differential signal measurements required for many of today’s high-speed power-related measurements such as motor drives, automotive differential bus measurements, and high-speed digital system designs.
-
Product
Multi-Channel, Programmable Current Source
CS-48-100
-
The Model CS-48-100 is a multi-channel, programmable current source. Developed for both semiconductor and digital superconductor electronics, it is computer-controlled and features 48 low noise current source outputs. Each source output has the capability to both set and read back currents and can be set to a zero current high Z mute state. Each of the 48 sources are optically coupled for control and are sourced from their own secondary winding for complete galvanic isolation. The device consumes a maximum of only 80 W and handles a maximum load current of 4.8 A total over all outputs. Operating over a range of 0-100 mA on each channel, the device features accuracy of +/-25 ?A. The mute state can be set thru a rear panel interlock or from the front panel button for maximum circuit protection. The unit can be mounted in a standard-sized rack.
-
Product
Imaging Mass Microscope
iMScope QT
-
Inheriting the concept of a mass spectrometer equipped with an optical microscope from the iMScope series, the iMScope QT is also Shimadzu's flagship model for MS imaging with a Q-TOF MS(LCMS-9030).
-
Product
RS-232, RS-422, or RS-485 to Fiber Optic Line Driver
Model 8277
-
The Model 8277 is a unique asynchronous fiber optic modem whose optical interface can operate in either point to point or ring (daisy chain) configurations and whose electrical interface can also operate in point to point or multi-drop configurations depending on the user selected interface.
-
Product
Acute 48-Channel, 16-Event, 400Mbps, 256Mb/channel, Data/Pattern Generator
Acute DG3064B
-
Model / Data Channel / Event Channel / Pattern DepthDG3064B / 48 / 16 / 256Mb/ch (max)DG3096B / 80 / 16 / 256Mb/ch (max)DG3128B / 112 / 16 / 256Mb/ch (max)
-
Product
Pneumatic Controllers
Campo Series
-
The Campo series of indicating controllers are suitable for field mounting and allow accurate measurement of pressure or temperature by associated primary measuring element; a dedicated model is available for generic 3 to 15 psi pneumatic input.These instruments provide high reliability with dynamic response, low maintenance, easily replaceable components, low air consumption, and improved compatibility with pneumatic valves.
-
Product
Single-Port Tunable Laser System Source
N7711A
Laser Source
The Keysight N7711A and N7714A tunable lasers are single-port and four-port sources, available with C-band or L-band wavelength coverage. The narrow linewidth and offset grid fine-tuning capability make them ideal sources for realistic loading of the latest transmission systems. All models can reach any wavelength point within their specified wavelength range just like all other Keysight tunable lasers. In this mode, code compatibility with existing test setups based on Keysight's range of full-size and compact tunable lasers is a great asset. In system loading applications, it may be preferable to grid-tune the lasers like system transmitters, simply by changing the channel index. The channel grid is adjustable to standard ITU-T grid spacing like 50 GHz, and to arbitrary grids. Likewise, the zero frequency (base channel) of the chosen grid is adjustable. A 12 GHz fine-tuning range allows de-tuning the frequency.
-
Product
Digital Tank Test Kit
4109
-
The voltmeter included in the kit, the “Model DPM” voltmeter, is designed for ease of use by meter readers and corrosion technicians alike and the voltmeter comes with an integrated RE-5 reference electrode attached for “metallic structure-to-soil” potential difference readings. The kit also includes a special test lead that has a brass thumb screw on one end which allows the test lead to substitute for the RE-5 reference electrode. This substitution allows the voltmeter to take “structure-to-structure” potential difference readings. The voltmeter offers two ranges, ±2VDC and ±20VDC with a 20MΩ input impedance. Since the voltmeter is digital [in contrast to the meter in our analog tank test kit (Cat. # 4108)], both negative and positive voltages are displayed. `
-
Product
UV Fluorescence Hydrogen Sulfide Analyzer
Model T101
-
The Model T101 H2S analyzer uses the proven UV fluorescence principle to measure hydrogen sulfide at levels commonly required for ambient air monitoring.The Model T101 is equipped with an internally mounted catalytic converter set at 315°C to convert H2S to SO2. A switching mode alternately measures H2S and SO2 while showing both readings concurrently on the front display.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T101 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Total Hydrocarbon in Water Analyzer
Model 4080
-
Teledyne Analytical Instruments
The Model 4080 is designed to detect hydrocarbons (C1-C9+) which may not absorb in the UV region)
-
Product
Portable, Industrial Duty Hygrometer
PDM75-X3
-
Model PDM75-X3 delivers the Edgetech Instruments Advantage: an ideal system tailored to your application needs. A modular chilled mirror sensor configured to meet your dew point requirements and the chemical resistivity of background gases. Choose the customized sampling system designed to match your process requirements. Select the best user interface options to meet your needs.
-
Product
PXI 20Amp 28Volt 2xSPDT Automotive Relay
40-181-011
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC. The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
Microwave Testing
10
-
PICOPROBE® MODEL 10 is a multipurpose, high speed, passive probe which can be used for driving as well as receiving signals. The Model 10 consists of a one meter length of flexible 50 ohm coaxial cable terminated by a carefully trimmed SMA on one end and by a miniature, high speed 50 ohm connector, specially developed to receive Model 10 replaceable coaxial probe tips, on the other. The 50 ohm coaxial cable was custom designed for Model 10 to be high speed, yet very flexible, so that moving the cable would not disturb the probe points.
-
Product
LED Optical Aging Test Instrument
LEDLM-80PL
-
LEDLM-80PL LED Lumen Maintenance and Aging Life Test System is designed according to standards of IES-LM-80, IES-LM-82, TM-21 and GB2312-80, and the software is developed base on Arrhenius model. LED has the features of long life, but with the different working condition and drive current, its life will be different, but generally the life will be around 50K hours. Differ from the traditional lightsource, LED light will decay gradually rather than extinguish instantly, so in the standard of LM-80, it introduces L70, L50 and etc.
-
Product
PCI to PC/104+ Bus Adapter
327/328
-
Model 327 and 328 are bus-to-bus adapters that allow operating a PCI board from a PC/104+ card stack. They allow selection of important PC/104+ signals using jumper plugs, thereby avoiding the requirement of using hardwired settings. Model 327 aligns the PCI board parallel to the PC/104+ boards, while model 328 places it perpendicular.
-
Product
Linear Motion Tandem Transducer
-
Columbia Research Laboratories
The Columbia Model LMT-50 is a unitized rugged package consisting of tandem linear variable differential transformers (LVDT's) with probe assembly. The LMT-50 is designed so that the likelihood of a single failure affecting both output signals is extremely improbable. The model LMT-50 offers flight proven performance, even in the most severe environments.
-
Product
Thermal Conductivity Transmitter
Model 2000XTC
-
Teledyne Analytical Instruments
The Model 2000XTC Transmitter resets the standard for thermal conductivity detector based applications with the process control industry. As an intrinsically safe transmitter, packaged within a rugged, weatherproof housing, the 2000XTC is suitable for use in harsh, hazardous outdoor environments. Using a novel, solid-state thermal conductivity sensor, this cost effective transmitter can be configured to detect H2, He, N2 Ar, CO2 a number of other gases of or a number of other gases of interest in binary or multi-component interest in binary or multi-component sample gas mixtures.
-
Product
UV Absorption O3 Analyzer
Model T400
-
Teledyne Advanced Pollution Instrumentation
The Model T400 UV Absorption analyzer uses a system based on the Beer-Lambert law for measuring low ranges of ozone in ambient air.A 254 nm UV light signal is passed through the sample cell where it is absorbed in proportion to the amount of ozone present. Periodically, a switching valve alternates measurement between the sample stream and a sample that has been scrubbed of ozone. The result is a true, stable ozone measurement.
-
Product
High Voltage Linear Power Supplies Bipolar 4-quadrant, Analog/Digital/Local Control, Ultra Low Ripple/Noise
Series BOP-HV
-
The Kepco Model BOP 500DM and BOP 1000DM are high voltage power sources, up to 500V or 1000V, respectively. These combine the capabilities of fast programmable power supplies with a Class A output stage, which can respond bidirectionally from zero. The BOP-HV can be operated in either a "voltage stabilizing" or "current stabilizing" operating mode (selectable by a front panel switch). These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
Product
Enclosure, 9050, Hinged Cover, 6" Depth
410112463
Enclosure
Enclosure, 9050, Hinged Cover, 6" DepthNot compatible with 9050 ITA frame p/n 410104110 or any older model 9050 ITA frame not matching the current height of 9050 ITA frames of 14.57". Questions? Contact Us before purchase.
-
Product
Disconnection Detector for PV
NSEI-100D
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*This device can detect the disconnected & broken point of DC current lines between PV panels and power conditioners in PV systems, without cutting power off and without climbing the roof where PV modules are located.*Furthermore, this model can find out the disconnecting point by applying the attached detector to the specific PV module.
-
Product
High Elongation Extensometers
Model 3800
-
Jinan Testing Equipment IE Corporation
The main body of this unique extensometer remains stationary during testing, held in position by the adjustable magnetic base included. Only the very light, small traveling heads move as the sample elongates during a test. These attach to the sample with small spring clips. Each head pulls a cord out from the extensometer as the head moves. These models use high precision, low friction potentiometers, and, as a result, have a wide range of factory selectable outputs. The extensometer is driven by an excitation voltage and has output proportional to the input. They can be provided with high level outputs (approximately 2-8 VDC) or ones that mimic strain gaged devices (2-4 mV/V). When set to mimic strain gaged extensometers, the Model 3800 can be used with virtually any signal conditioning electronics designed for strain gaged sensors. The potentiometers employ a hybrid wire wound around conductive plastic, which provides excellent long term stability. The output from the extensometer is readily interfaced with most existing test controllers, and may be directly input to data acquisition systems and chart recorders. Please let us know at the time of order what type of output and connector you require.
-
Product
Energizer BLACK Vibration Exciter for Buzz, Squeak & Rattle (BSR) Testing
Energizer BLACK Vibration Exciter
-
The Energizer BLACK Series is part of a family of extremely quiet vibration exciters. The Series is ideally suited for the support of subjective and objective BSR evaluations according to industry test specifications, such as GMW14011, GM7293TP, BMW PR311-2 or PSA “Specification bruit parasites”, as well as several Hyundai Engineering Standards. With availability in four unique models and sizes, the Energizer Series is expressly designed to support such evaluations, while reducing the risks of measurement uncertainty caused by unwanted vibration exciter noise occurring within the BSR test environment.
-
Product
Telecom Gas Monitors
SMC 2350/2360
-
The SMC 2350/2360 Telecom Gas Monitors both continuously monitor for the presence of Carbon Monoxide (CO), but the Model 2360 also monitors for combustible gases.
-
Product
PXI Power Multiplexer, 18-Channel, 1-Pole
40-665A-001
Multiplexer Module
Model 40-665A-001 is a 18-Channel 1-Pole Power Multiplexer, suitable for switching inductive/capacitive loads up to 10A at 250VAC. It is available with a choice of 1-pole (10A) or 2-pole (8A versions).
-
Product
Creep and Stress Rupture Tester
QualiCreep Series
-
Qualitest Creep and Stress Rupture Tester - QualiCreep Series is mainly designed to perform Creep and Stress Rupture testing of a wide variety of materials to both standard and customized specifications such as ASTM E139, ISO 204, ISO/R 206 and similar international standards. These machines are capable of covering the determination of the amount of deformation as a function of time (creep test) and the measurement of the time for fracture to occur when sufficient force is present (rupture test) for materials when under constant tensile forces at constant temperature. Qualitest offers three models electronic high temperature creep-testing machine with full closed-loop servo-control in capacities from 10kN to 500kN.
-
Product
PXI 64x2 Matrix Module, 1-Pole, 2A, 60W
40-527A-001
Matrix Switch Module
The 40-527A, is a PXI single-pole 64x2 matrix and is part of a range of matrices supporting 128 crosspoints. All models use gold-plated contact electromechanical relays.
-
Product
10 MHz To 54 GHz LAN Thermal Vacuum Compliance Power Sensor
L2066XT
Power Sensor
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
Geophysical Instruments
SSR-MP-AT-SAL
-
Integrated Geo Instruments & Services Private Limited
The IGIS signal stacking based Signal Enhancement Resistivity Meter Model SSR-MP-AT-SAL is a state of art microprocessor based data acquisition system. The instrument design incorporates several innovative features and advanced techniques of digital circuitry to make it a reliable geophysical tool providing high quality data useful for mineral and groundwater exploration and any other geophysical applications.
