-
Product
Pulse generator
9355-1
-
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
Product
4-Channel 200 MHz A/D with DDC, Kintex UltraScale FPGA - XMC
Model 71861
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Wear Testing Machine
M-2000
-
Jinan Testing Equipment IE Corporation
Model M-2000 Wear Testing Machine is to be used test the anti-wear performance for metal and non-metal specimen under the sliding, rolling, and sliding-rolling condition. The Wear Testing Machine can also test various materials under dry-friction and wet-friction. The wear testing system can calculate friction work & friction coefficient by the data acquired. The Wear Testing Machine is widely used in universities, research & scientific institutes.
-
Product
EXG Signal Generators
-
The cost-effective EXG X-Series signal generators address critical speed and uptime needs for manufacturing test. With analog and vector models, the EXG provides the signals you will need for basic parametric testing of components and functional verification of receivers.
-
Product
UV Fluorescence Hydrogen Sulfide Analyzer
Model T101
-
The Model T101 H2S analyzer uses the proven UV fluorescence principle to measure hydrogen sulfide at levels commonly required for ambient air monitoring.The Model T101 is equipped with an internally mounted catalytic converter set at 315°C to convert H2S to SO2. A switching mode alternately measures H2S and SO2 while showing both readings concurrently on the front display.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T101 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Model LG: Drywall Moisture Meter
MRC006505
-
Provides average moisture content down to a penetration of 1in. Uses radio frequency capacitance to measure the moisture content of gypsum wallboard. 0% - 25% moisture range.
-
Product
Thermal Shock Chambers
-
Weiss Technik Thermal Shock chambers are designed to give quick transitions between a HOT and COLD temperature zones. Available in vertical, horizontal and liquid models. Thermal stock chambers are used in all industries including Automotive, Electronics, Aerospace, and others to help find product defects in electronic components and product assemblies. Thermal shock is important with MIL -STD 883 test standard.
-
Product
BIM Consulting Services
-
Being Revit BIM outsourcing company, our consultants facilitate 3D Modeling (Architectural, Structural, and MEP), 4D BIM Construction Scheduling, 5D Cost Estimation, Clash Coordination, Scan/PDF/CAD to BIM Conversion, Shop drawing, Construction Documentation . Tejjy Integrated project delivery with Autodesk Revit software for Architecture, Structure, MEP workflow allows smooth execution through a quality assured BIM Management lifecycle.
-
Product
ARINC 429 USB & LAN Test & Simulation Module
UXI-429
-
Avionics Interface Technologies
8 Channel (4Tx/4Rx) & 16 Channel (8 Tx/8 Rx) models available - Programmable Tx channel output amplitude - Programmable high/low speed operation - Concurrent operation of all Tx/Rx channels at high speed rates - Full error injection & detection - Rate-oriented label transmission - Label selective trigger for capture/filtering - Real-time recording & post analysis of multiple channels - Physical Bus Replay - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs)
-
Product
3D Scanner
Artec Leo
-
The first 3D scanner to offer onboard automatic processing, Artec Leo is able to provide the most intuitive workflow, making 3D scanning as easy as taking a video. As you scan your object, see the 3D replica being built in real time on Leo’s touch panel screen. Rotate the 3D model, check if you have captured all areas, and fill in any parts you may have missed.
-
Product
2U 4 Slot VME64X Mini Crate
VME8004X
-
The Model VME8004X is a 4 slot VME crate, suitable for 6U x 160mm boards, with VME64x compliant backplane. The Unit is powered by 100 – 240 Vac (50 – 60 Hz). The power distribution is 25A@+5V, 10A@+12V, 10A@-12V, 25A @3.3V. The VME8004X provides automatic daisy chain and supports CBLT data cycles.
-
Product
Test System
BMS HIL
-
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
Product
Specialty Antennas
-
*Application and industry specific designs*Stealth radomes available on select models*Customization available
-
Product
Floating Point FFT
IEEE-754
-
Abaco Systems' Floating Point FFT core is the most flexible IEEE-754 compliant FFT core available in the FPGA world. Designed for high performance programmable devices from Xilinx and Altera, this core performs Fast Fourier Transforms ranging from 256 points to 64M points and is ideal for high precision spectral analysis, radar and video processing applications. Download our bit-true model for 1D and 2D FFT.
-
Product
Femtosecond Fiber Lasers
-
Best in class femtosecond fiber lasers: highest output power, lowest phase noise, highest reliability. Choose the perfect model for your application from our Erbium and Ytterbium fiber lasers with center emission wavelengths from the visible to the NIR, and extending to the Mid-IR in selected models.
-
Product
Programmable RF Attenuators
-
The AD-USB R3 is AdauraTech’s latest design in the AD-USB series of programmable RF attenuators. Combining all the best features of the previous models, the R3 is the new series flag ship. With a completely custom machine aluminum enclosure, the R3 boasts 95dB of attenuation. The addition of Ethernet allows EASY implementation into the most modern of test setups by allowing network control via HTTP web interface or direct Telnet while the USB port powers the device and allows for serial communication.
-
Product
Broadband Optical Source - MATRIQ
-
Our SLED MATRIQ instrument is a compact super-luminescent LED light source with high output power, large bandwidth and low spectral ripple.The SLED comes in various wavelength models to address various key applications across telecom and datacom, and is ideal for building a customized optical testing platform that delivers reliable and repeatable results.
-
Product
Benchtop Water Quality Meters
LAQUA PH1300
-
Water quality analysis is repeatedly performed in laboratories on a daily basis. Our high-end benchtop model was developed to provide simplicity with excellent on-site usability - from operation and maintenance through to troubleshooting.
-
Product
Paramagnetic O2 Analyzer Optional CO2 Sensor
Model T802
-
Teledyne Advanced Pollution Instrumentation
The Model T802 O2 uses the proven paramagnetic measurement principle, coupled with state of the art microprocessor technology, to provide accurate and dependable measurements of Percent-Level O2.Paramagnetic technology is non-depleting, which means that there are no consumable parts, and ensures a consistent performance over time. The selectivity of the paramagnetic measurement for oxygen means that there is little or no interference from other common background gases. The T802 offers a stable and inherently linear measurement of oxygen, making it possible to calibrate the analyzer by checking only two points. There is no requirement for a reference gas during operation.
-
Product
Full Band Scalar Network Analyzer Extenders
-
Full band scalar network analyzer extenders are designed to extend low frequency scalar network analyzers to higher millimeterwave frequency ranges. These extenders offer a low cost means of producing millimeterwave scalar network analyzers while preserving the functionality and features that industry standard models offer. These extenders deliver a superior performance since they are assembled with SAGE Millimeter’s instrumentation grade frequency extenders (STE series), Faraday isolators (STF series), direct or programmable attenuators (STA series), directional couplers (SWD series) and waveguide detectors (STD series). The below standard offering covers the frequency range of 26.5 to 170 GHz. Specifications other than those listed below are available upon request.
-
Product
Equalizers
-
Voltage variable and fixed slope modelsPrecise attenuation slope control50 and 70Ω models
-
Product
Man in the Middle Cable
MitM
-
The Man-in-the-Middle Cable (Catalog No. MitM) was created to work with the T4000 and T4350 to enable a technician to use an electric vehicle rather than a very large load emulator to absorb the energy delivered by the DC fast charger during charger testing. It currently comes in 350 Amp CCSI and 200 Amp Tesla/NACS models, each with charging connector holders and digital temperature sensors.
-
Product
Thermal Quad Scanner
-
Thermal Quad Scanner has the Highest Isolation of any 4-Terminal Scanner and operates at up to 1000V. With a Guildline model 6664C scanner and software, hard-to-make high ohm measurements (up to 100 GΩ) can be automated and scheduled at any time that is convenient to the metrologists, even at night and over the weekends.
-
Product
Nano Particle Size Analyzer
SALD-7500nano
-
Delivering 10 times the sensitivity of previous models, this innovative analyzer is capable of continuously measuring changes in particle size and particle size distribution at one-second intervals, within a range spanning 7 nm to 800 μm. In addition, unique options that accommodate the measurement of even high-concentration samples (up to 20 wt%) and trace quantity samples (down to 15 μL) are available. Due to its leading-edge measurement capabilities, the analyzer will likely be used for many applications in new areas, including nanotechnology, the life sciences, and fine bubbles (microscopic bubbles).
-
Product
RS-232, RS-422, or RS-485 to Fiber Optic Line Driver
Model 8277
-
The Model 8277 is a unique asynchronous fiber optic modem whose optical interface can operate in either point to point or ring (daisy chain) configurations and whose electrical interface can also operate in point to point or multi-drop configurations depending on the user selected interface.
-
Product
High Temperature Self-Supporting Furnace Extensometers (1200 C)
Model 3448
-
Jinan Testing Equipment IE Corporation
Epsilon developed this unique high temperature extensometer for testing metals, ceramics, and composites at the high temperatures produced by furnaces and induction heating systems. A combination of features make these extensometers easier to use and better in performance than other similar high temperature extensometers.The units are held on the specimen by light, flexible ceramic fiber cords. These make the extensometer self-supporting on the specimen. No furnace mounting brackets are required. The side load on the test sample is greatly reduced because of the self-supporting design and light weight of the sensor. Most materials testing furnaces with a side cut-out for an extensometer will readily accept a Model 3448. For induction heating systems, a different ceramic cord placement allows the extensometer to easily pass between the coils.The combination of radiant heat shields and convection cooling fins allow this model to be used at specimen temperatures up to 1200℃ (2200°F) without any cooling. An optional tiny air fan does enhance stability at the highest temperatures and is recommended for the highest accuracy and for tests with small elongations. The fan comes with a magnetic base for support so it can be mounted at any convenient location near the extensometer. Fan cooling is not generally needed for induction heated systems. High purity alumina ceramic rods are used. These are available in lengths as required to fit your furnace. A spare set is included with every extensometer. Specify chisel, vee chisel or conical contact points as desired.Most units operate equally well in tension and compression. Thus tensile, compression and cyclic tests like low cycle fatigue can all be performed with a single unit.For vacuum furnaces, special models are available. Epsilon can also provide a radiant heat transfer cooled version. This requires that the extensometer module be surrounded by a water cooled enclosure with a front slot for the ceramic rods.
-
Product
Digital Pen Meter
PM-2
-
Our compact, low cost Model PM-2 Digital Pen Meter is ideal for general electrical testing and troubleshooting. A few applications include HVAC, automotive, electrical/power, and environmental monitoring uses.
-
Product
Pressure Control Setup Using Pid Controller
ULP-26
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Pressure Control Setup comprises of Pressure tank fitted with pressure transmitter to measure the pressure. The pressure is controlled by a pneumatic control valve operated by a I to P converter. The whole system is mounted on a Table top Model with all necessary Piping. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
-
Product
Environmental Simulation Chambers
-
GTEMCELL , currently provide environmental test chambers made by LIB.Our standard range of test chambers includes bench top and floor standing models, across temperatures ranging between -65℃ and +150℃ (from -80℃ to +200℃ for specific applications), and humidities between 10% and 98% RH.
-
Product
Charge Meter
NK-1001A/NK-1002A
-
Probe-type charge meter that can easily measure the amount of discharge charge that causes static electricity destruction in the manufacturing, inspection, and assembly processes of electronic devices.Many ESD phenomena that impair electronic devices are represented by the CDM ( Device Charging Model). The CDM is a model that represents a phenomenon in which a high peak current flows at high speed when the device itself is charged and its external electrode is grounded. The coulomb meter measures the amount of discharge charge, which is the integral value of the current, with high accuracy.
