Noise Monitors
-
product
Noise Sources
WGNS
The system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device operating in the 26.5 – 170GHz range on wafer as well as in benchtop applications. Farran offers the WGNS series of noise sources to be used in conjunction with the FBC down converters for use as frequency extenders for noise figure measurement test system.
-
product
Phase Noise Testing
The systems are based in the UK although testing for any company world wide will be undertaken.
-
product
Bridge Monitoring
Structural Health Monitoring of BridgesDewesoft data acquisition systems are used in structural health and seismic bridge monitoring projects ranging from structural mechanics to continuous monitoring of large, complex structures. The systems provide distributed, high-channel-count and remote monitoring for highway overpasses, roads, buildings, and bridges.
-
product
CEMS II E Continuous Emission Monitoring System
CEMS II e takes away the manual configuration and settings adjustments from your day-to-day emissions measurements. A fully automated continuous emission monitoring system CEMS II e is TÜV and MCERTS certified solution (QAL1) to offer environmental compliance. This emission monitoring system is suitable for measuring pollutants continuously from hot, wet and corrosive gas streams in various industrial processes, such as powerplants, waste incineration, cement plants and beyond.
-
product
20Hz Injection Kit Monitoring System
Signals & Systems India Private Limited
The Display used to monitor the 20Hz and 50Hz current passing through NGT transformer. This could help to monitor the stator earth fault and could record the current every minute. The current shall be displayed in milliamps for both 20Hz and 50Hz. If an earth fault occurs in the generator star point, the 20 Hz voltage drives a current through the fault resistance. The current can be measured using clamp-on CT which would be clamped between load resistor and NGT. It gives an indication of the current values are lower or higher than the set threshold.
-
product
Site Vibration And Noise Testing
Response Dynamics Vibration Engineering, Inc.
Effective vibration isolation is critical to the performance of many systems. It is often much more challenging than expected because the structural dynamics of the supporting structure, and the isolated structure, also affect the isolation performance. Isolation resonances can often create other vibration problems and confound an engineering team. We have successfully designed vibration isolation into countless systems over the years using unique custom solutions as well as adapting standard components and applying them properly to the design.
-
product
Video QoS Monitoring Web Management Software
TSM Web
The TSM Web is a web service program for managing Mividi Video Monitoring Systems or Multiviewer Systems. It provides an Internet gateway to Mividi Video Monitoring servers in order to remotely access test results and configure the test servers using the Internet.
-
product
Monitor SDR Boards
Multiple Access Communications Ltd.
MAC Ltd’s MONITOR product family includes a number of software-configurable digital signal processing platforms intended for use in radio frequency (RF) receiver and transceiver applications. The MONITOR products are available in assembled printed circuit board (PCB) form for integration into larger systems. They also form the basis of MAC Ltd’s CatchAll™ radio products. In addition to the standard products listed below, MAC Ltd is happy to discuss the customisation of existing products and/or the development of new bespoke hardware and software.
-
-
product
Active Monitoring or Synthetic Transactions
CloudReady
Always-on, end-to-end user experience monitoringNo complex scripting required, Exoprise maintains the actions the sensors takeMonitors app performance via both Web UI and API transactionsFull network path performance information for correlation and outage detection
-
product
Radon Professional Monitoring
Our dedicated range of products and accessories has been especially designed to fit these needs and to provide accuracy in the following application fields: Short and long-term monitoring of radon concentration indoor and outdoor, water and soil gas analysis Radon surveillance and mitigation at workplaces (according to valid radiation protection regulations) Geological survey, e.g. vulcano watching, earthquake surveillanceAlphaGUARD products reputation is worldwide recognized, as a reference device for calibration for active and passive radon detectors.
-
product
Occupational Noise Measurement System
NK122
This Occupational Noise Measurement System is designed to give Health and Safety Managers, or any other professional with responsibilities for managing noise in the workplace, everything they need to protect your workforce from over exposure to noise and to help you ensure your company is complying with The Control of Noise at Work Regulations 2005.
-
product
Ultra-Low Phase Noise Amplifiers
When phase noise is critical, turn to Mercury’s line of low phase noise amplifiers. Taking full advantage of the industry’s best device technology, these parts are designed to meet the toughest requirements. Through Mercury System’s advanced production capabilities, phase noise can be accurately measured—even during environmental tests, such as vibration.
-
product
Waveform Monitors
LV5300
The LV5300 is a waveform monitor with a 7-inch touch screen display in a compact 3 U enclosure operative with battery power supply.
-
product
Low Noise Differential Preamplifiers
Provide a high gain amplification to 1MHz with an AC output derived from a very low noise FET instrumentation amplifier. Each model has fixed gain settings of x1 (0dB), x10 (20dB), x100 (40dB) and x1000 (60dB) over a selectable bandwidths of 100Hz, 1kHz (HP), 3kHz, 30kHz, 100kHz and 1MHz (7000 model only). Noise referred to input is 7nV√Hz and common mode rejection is >100dB at 1kHz. Momentary pushbutton switches are provided that control coupling, bandwidth, gain and channel on/off selections. BNC connectors are provided for single-ended and differential input, ac output, and dc output (optional) connections.
-
product
Water Quality Monitoring System
WQMS
Water Quality Monitoring System (WQMS) is a facility to measure pollutants such as Chemical Oxygen Demand (COD), Total Phosphates (TP), Total Nitrogen (TN) etc. The required parameters are customized according to the type of factory and discharge regulations.
-
product
IMPATT Noise Generator CW & Pulse At W-band, 94 GHz :
The device consists of two modules, a cable that connects them, and a power cable. The first module (I) contains the power supply (AC 115 V), regime switch mechanism and a generator of a series of pulses. The second module (II) is the noise generator. Photo 1: Module I - Power Supply
-
product
Low-PIM, High-Power Filter Solutions for Monitoring Broadband Emissions
Enables monitoring of PIM to 13 GHz; 100W CW and 1KW peakNear-end monitoring: Carriers rejected -90dB by the notchtravel through the bandpass filter to the low PIM termination.Far-end monitoring: Carriers rejected -90dB by the highpass,IM products passed are monitored by the spectrum analyzer.
-
product
Economical Monitoring Platform
Torque DVMon
The DVMon is an economical monitoring platform for digital television networks. Built on the latest compact 1RU hardware, the DVMon raises the bar in user experience through its distinct, flexible HTML5 GUI. Running on any standards-compliant web browser, it allows opening of any number of windows in any size. The DVMon also facilitates opening multiple viewing panels within each window, and eases zooming in or out on any chart axis.
-
product
Ultrafast Photodetector with Current Monitor, 700 - 870 nm, DC - 25 GHz, FC/PC
DXM25CF
The DXM25CF Ultrafast Detector is a DC - 25 GHz, fiber-coupled, GaAs-based photodetector designed for applications in the 700 nm - 870 nm wavelength range. The core element of the detector is the fiber-coupled, hermetically sealed, microwave detector module. For convenience and simplicity of use, the module is mounted inside a rugged housing that includes a rechargeable battery, current monitor circuitry, and a digital display of the DC photocurrent.
-
product
Audio Monitors
TouchMonitor TM9
The all-new audio metering units of the TouchMonitor range is RTW‘s answer to growing requirements in today‘s production, post-production, and broadcast world. Equipped with high-grade 7“ or 9“ touch screens and an easy-to-use GUI, TouchMonitor enters a new level of professional audio metering in terms of precision, performance, efficiency and flexibility.
-
product
Low Noise Preamplifier
The UPL-3001 preamplifier is a high performance solution for the low-noise amplification of ultrasonic signals. Designed for signals ranging from 0.5 to 300 MHz, the small and lightweight, rugged unit is perfect for remote applications. This is ideal for P&C, TT, AUT or TOFD inspection.
-
product
Chemitec Sensors And Analyzers To Monitor Oxidants In Water
Chemitec's S494 series of amperometric probes provide continuous, accurate monitoring of chlorine and other oxidants in clean water applications. A range of sensors assures accurate measurement of oxidation, with sensors optimized for Chlorine (total, organic or inorganic), Chlorine Dioxide, Ozone, Peracetic Acid, Hydrogen Peroxide, Bromine, or Chlorites.
-
product
Intelligent Application and Service monitoring
Datadog
With turn-key integrations, Datadog seamlessly aggregates metrics and events across the full devops stack.*SaaS and Cloud providers*Automation tools*Monitoring and instrumentation*Source control and bug tracking*Databases and common server components*All listed integrations are supported by Datadog
-
product
HF / HCl Concentration Monitor
HF-960H
The HF-960H accurately measures concentrations of hydrofluoric and hydrochloric acid used in semiconductor manufacturing and other processes. The dedicated FES-510 series sensor is made from materials that are highly resistant to chemicals, making this unit ideal for the management of hydrofluoric and hydrochloric acid, even in high concentrations.
-
product
Microwave Monitor w/ Vinyl
A100p
This single-range, RF power measurement instrument is designed to operate in the 2.45 GHz range. Used by field service engineers, engaged in the repair and maintenance of commercial and domestic microwave heating equipment, its primary function is the detection RF microwave energy leakage.
-
product
TPMS - Tire Pressure Monitoring System Sensors
The new Bosch Universal Sensors for Tire Pressure Monitoring Systems (TPMS) measure the air pressure of the vehicle’s tires in real time and transmit it directly to the control unit by radio. Universal, compact and easily programmable, Bosch QUICK FIT sensors offer a vehicle coverage of over 90% with just two part numbers.
-
product
Tool and Process Monitoring
BK MIKRO
BK Mikro is typically used as a broken tool detection system but can also be used for many other applications such as object inspection, position recognition and checking for part defects. The selection of the scanner and controller for broken tool detection systems is mainly application based. Follow the links below to explore specific models or contact us with application questions about our broken tool detection systems.
-
product
9KHz-2.1GHz, Spectrum Analyzer, Phase Noise<-98dBc/Hz, Amplitude Accuracy<0.7dB, 10.1" Color Display
T3SA3100
9KHz-2.1GHz, Spectrum Analyzer, Phase Noise<-98dBc/Hz, Amplitude Accuracy<0.7dB, 10.1" Color Display.
-
product
Generator Monitoring Unit
Avoids the requirement of 2 different meters (energy and VAF in one)Reduces the cost and simplify wiringHigh resolution reading with auto scaling in LEDEnergy consumption in counter even if CT is reversed
