Source Measurement Units
-
product
Optical Light Source
TM3111
TM3111 optical light source is a handheld optical light source, It can provide 1 to 6 wavelengths output to satisfy specific requirements including the 650nm visible light source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer’s needs.
-
product
Tilt Switch and Control Unit
MTS / SCU-200
Features • Detects the presence or absence of bulk material • Standard enclosure is NEMA 12 with indicator lights • NEMA 4 and Intrinsically Safe enclosures available • Rugged heliarc-welded steel probes • Use with SCU-200 for complete monitoring system
-
product
L-Band ASE Light Source
ASE6000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai ASE6000 series is L-Band ASE light source with featured with high stability and high output. It is mainly applied for testing of L-Band optical components and optical communication equipments as well as Fiber Optical Sensor etc. Huatai ASE6000 has three types of exterior structure, suitable for different customer’ requirements.
-
product
Data Broadcast Units
The DBU-TTL Data Broadcast Unit is designed for use in receive only data broadcast applications. The unit supports 8-Ports Data/Clock distribution of TTL signals on BNC connectors. 1U rack mount chassis.
-
product
Lighting Management Units
Highly integrated, flexible lighting management ICs support nearly all the illumination tasks performed in mobile phones.
-
product
AC Power Sources
i-iX Series II
AMETEK Programmable Power, Inc.
The iX Series II represents a new generation of AC and DC power source that addresses increasing demands on test equipment to perform more functions at a lower cost. By combining a flexible AC/DC power source with a high performance power analyzer, the iX Series II systems are capable of handling complex applications that have traditionally required multiple instruments.
-
product
Visible Laser Source
VLS35
The KD Optics VLS-35 is a pocket sized, visible source used for testing fibre optic cable installations. The unit is pocket sized with a long battery life from a PP3 battery, making it ideal for local fault finding and continuity checking of fibres.
-
product
Voltage Integrated Sources
VIS
The VIS voltage integrated source was designed to be used as a stable alternating voltage source for electricity meter test equipment, and in laboratories. The output voltage is isolated and independent of mains voltage. VIS is available in a variety of configurations depending on the values of output power and output voltage.
-
product
Single Filament Sources
Get a cost-effective solution that’s ideal for your high-volume, high-value MBE process needs with reliable Veeco Single Filament Sources. They feature dependable band thermocouples and single heater filaments for 750-1200°C operation. Three system configurations, and many crucible sizes, are available. All offer stable and consistent fluxes of high vapor pressure materials.
-
product
Excitation Light Source
Various spectral irradiation is possible by combining various light sources + spectroscope + irradiation system.We will also respond to special order correspondence. We will provide light suitable for your desired intensity such as light intensity and wavelength.
-
product
AC Source
AFC
The AFC Series products are single and three phase AC Power sources ranging from 0.5kVA to 2000kVA. This AFC series has a continuous and adjustable output voltage between 5~300V. This allows for quick and convenient 3 scales of preset voltage for high and low voltage simulation. Power is supplied by state-of-the-art IBGT pulse width-modulated power amplifiers resulting in highly efficient power conversion, compact design and maximized performance. With up to 90% efficiency the AFC minimizes heat dissipation so less infrastructure cooling is required.
-
product
Calibration Light Source
CAL1
Image Engineering GmbH & Co. KG
The one light source solution in the field of camera characterization and calibration. CAL1The CAL1 calibration light source is designed to characterize and calibrate cameras in the lab or on the production line. Its compact design consists of one iQ-LED element in a 0.3 m integrating sphere that illuminates a 70 mm opening. Because of the non-reflective special diffusor filter on the sphere opening, a uniformity of more than 98% could be reached
-
product
Programmable Logic Units
- Programmable FPGA to implement complex logic functions- VHDL coding expertise not required- User-friendly software tools for board programming- Pre-programmed set of standard functions (N1081B/DT1081B)- Different I/Os connectors and standards available (NIM, TTL, ECL, LVDS)
-
product
Commutator Testing Unit
SCR ELEKTRONIKS have designed “Commutator Testing Setup” to provide Commutator manufacturers and users a simple and speedy method for testing their Commutators. This single station commutator testing set up therefore user can test one commutator at a time. In Automatic mode of testing this set up performs two tests automatically.
-
product
Voltage Regulator Testing Units
With the goal of providing the industry with the best products ahead of the curve, we continue to develop a complimentary line of Voltage Regulator Testing Units for laboratory and production testing.
-
product
Load Support Unit
LSU220A
The LSU220A is a general purpose load support unit designed to act as a permanent power supply to maintain backup battery systems whilst alternative sources of power are either impractical or unavailable, such as running diesel engines during maintenance programs.
-
product
Measurement
Multichannel Strain Gauge Meter
The Software Multichannel strain gauge meter is used for performing all types of strain gauge measurements using strain gauge sensors (for instance, force and torque sensors, bridge and semi-bridge circuits based on resistive strain sensors), strain measurement data acquisition modules ZET 017-T and digital strain gauge sensors of ZETSENSOR series. The program enables simultaneous processing of up to 128 measuring channels using strain gauge station and up to 500 measuring channels in the case if digital sensors are used.
-
product
Electrical measurements
Instruments for measurement and analysis in accordance with the regulations of single / triphasic low voltage networks and data networks via cable or fibre.
-
product
Railway Motion Control Unit
RMCU
The Railway Motion Control Unit – RMCU is a high-performance strapdown system developed for Railway applications to determine the absolute orientation (Heading, Pitch, and Roll) and motion parameters (Angular Rates and Linear Accelerations) for any Railway Platforms on which it is mounted. Orientation is determined with high accuracy for both motionless and dynamic applications.
-
product
Impedance Measurement
CITS880s
Finer geometries and thinner copper can present a challenge for fabricators measuring impedance on leading edge PCBs. The CITS880s answers that challenge with the introduction of Launch Point Extrapolation (LPE). LPE extrapolates the TDR response back to a point close to the start of the transmission line effectively allowing to users more accurately to measure the instantaneous or incident impedance of the line.
-
product
Measurement System
MS-500 series
The MS series is suitable for pre-processing analog signals.The plug-in units of filters, differential amplifiers, isolation amplifiers, etc. can be installed into their frames.(16 channels at maximum/the JIS rack size)
-
product
Calibration Sources
Accurately verify the output signals of your pyrometers, thermal imaging systems, heat-flux measurement systems, or spectrographic analysis systems. We offer unique and very precise Mikron® calibration sources. Our blackbodies feature cutting-edge emissivity values, homogenous emission areas, and various different-sized apertures. And fast heat-up times and high temperature stability are guaranteed.
-
product
Source Phase Control
S93088B
The S93088B allows users to set calibrated, arbitrary phase differences between two signal sources. The sources can be the analyzer’s internal sources or external signal generators routed through the analyzer’s test set. The phase difference can be fixed, or swept between two specified phase values. S93088B also controls the relative power level between the sources using the receiver-leveling feature.
-
product
Ignition Driver Units
A compact inductive ignition drive unit which drives two banks of five ignition coils. The drivers are controlled via direct logic signals from a host ECU and provide fire-by-fire diagnostics back to that unit via CAN. The coils can be run at voltages up to 30V with this unit in order to minimize dwell times for optimum response.
-
product
AC Power Source
SPS-100
Kongter Test & Measurement Co., Limited
SPS-100 is designed for various tests of analog and digital AC Voltage meter and Current meter, Single/three phase active and reactive power meter, Phase angle meter, Single/three phase power factor meter, frequency meter, and synchronous-meter, Single/three phase active and reactive power meter; it also outputs 2nd ~63rd harmonics.
-
product
Motor Termination Units
Since the rise time of IGBTs are in the range of a few tens of nanoseconds (between 50ns-200ns), even short cables between PWM motor drives and motors cause voltage doubling at the motor terminals due to Travelling Wave Phenomenon as in transmission lines. The insulation of motor windings are prone to failure due to high voltage spikes if necessary precautions are not sufficiently taken. RC Type Output Filter Modules reduce these high voltage spikes to protect motors by connecting to stator terminals.
-
product
Fuel Display Unit Tester
MS 1125
Fuel Display Unit Test Bench is a compact table-top test bench with front panel controls, indications, built-in signal simulator and necessary power supply for testing the serviceability of Fuel Display Unit of Helicopter. FTB operates on 230 V AC and supplies 28 V DC power to FDU. FTB is housed in a metallic cabinet FTB interfaces with both 61 Pin connector and 6-pin socket mounted on the rear panel of FDU by means of the cable connected to the unit. FTB is fabricated utilizing off-the-shelf standard industrial/commercial components like rotary switches, toggle switches, press switches, test sockets, fuse holders, potentiometer etc. The Frequency generation circuit is integrated into FTB for the simulation of Fuel probe and flow rate signals. The frequency of the signal can be selected by means of a rotary switch Low amplitude sine wave signal is simulated for testing flow rates. Variable voltage DC power supply with a voltage range of 24 to 29 Volts is provided within FTB to power-up FDU. 5 V DC is provided for the operation of signal generating circuit (PIC Frequency Controller Board). An off-the-shelf Hand held battery operated Digital Multimeter (DMM) procured from the prominent manufacturer (FLUKE) is supplied with FTB for setting up and measurement of various parameters like Resistance, Voltage, Frequency etc.
-
product
SLED Optical Source
JW8006 Series
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
SLED(Super luminescent light-emitting diode) is a super broadband optical source which is designed for fiber sensor;, optical fiber gyroscope, lab application field. It has the feature as broaden bandwidth, customizable center wave length, high output power, etc. Benchtop (for lab), standard module(150*125*20mm, with modulation function) and mini module(90*70*15mm) is available. The key component is employed the FWHM bandwidth up to 40nm high power SLEDs to ensure the spectrum performance. Stability is ensured by unique ATC and APC circuit. The output power is adjustable by RS232 or RS485 port.
-
product
High-Power Noise Sources
These modules not only contain the noise diode circuitry, but also gain stages to boost the output power. While lower frequencies (under 2 GHz) are most common, Mercury produces powerful amplified noise modules up to 18 GHz. Noise modules are available in coaxial, surface mount and pin type construction. TTL control options are available.
-
product
Noise Sources
NC3208
It offers a high ENR output AWGN noise over a wide frequency range. This Noisecom noise source has excellent stability with temperature and voltage for tough environments. It contains a hermetically packaged noise diode that has been pre-selected for special performance characteristics. This module is ideal for many different applications including radar warning receivers (RWR), built-in test equipment (BITE), military aircraft, and Wi-Fi.
