Signal Sources
Instrument that provides a stimulus signal (waveform). (www.tek.com)
See Also: Signal, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
Product
Signal Sources
-
Frequency multipliers, oscillators, beacon transmitters or microwave TV-transmitters: The signal sources of Kuhne electronic meet the highest quality standards and are remarkable for high spurious and harmonic rejection, low phase noise and very good frequency stability. Benefit from our experience in satellite technology and the commercial sector!
-
Product
PXI Signal Generators (Signal Sources)
Vector Signal Generator
Accelerate test throughput with fast, high-quality measurements optimized for RF or microwave design validation & manufacturing testIncrease test configuration flexibility with a PXI platform and license key upgradesReduce development time with easy integration of drivers and programming examples into test environments
-
Product
Source Phase Control
S93088B
-
The S93088B allows users to set calibrated, arbitrary phase differences between two signal sources. The sources can be the analyzer’s internal sources or external signal generators routed through the analyzer’s test set. The phase difference can be fixed, or swept between two specified phase values. S93088B also controls the relative power level between the sources using the receiver-leveling feature.
-
Product
Signal Generators (Signal Sources)
Vector Signal Generator
Meet your test requirements with the widest selection of signal generators with the best performance in every class, whether you need a traceable, metrology-grade solution or cost-effective basic signal generation
-
Product
Source Phase Control
S96088B
-
The S96088B allows users to set calibrated, arbitrary phase differences between two signal sources running on the E5080B ENA.
-
Product
Polarization Maintaining Fiber Components
-
OZ Optics offers a broad range of polarization maintaining components, patchcords, and connectors designed to resolve polarization problems, which are becoming increasingly important in today's higher speed and more complex mesh optical networks. By maintaining the polarization of the signal at its source, our polarization maintaining components minimize polarization mode dispersion and eliminate the effect of polarization dependent loss thereby increasing the quality of the signal that is transmitted throughout the network.
-
Product
Active Differential Probe, 100 kHz to 12 GHz
U1818B
High Frequency Probe
The Keysight U1818B 100 kHz to 12 GHz active differential probe makes it easy to perform high frequency in-circuit measurements using network, spectrum and signal source analyzers. With flat frequency response, low noise floor, and direct power from instrument connection, the U1818B allows measurements to be made while taking full advantage of Keysight's RF analyzers dynamic range.
-
Product
Process Calibrators
-
Handheld calibrator-multimeter of industrial process signals including voltage, current, resistance and temperature. External signals up to 200 V or 100 mA can be measured simultaneously with signal sourcing.
-
Product
SSA-X Signal Source Analyzer, 1 MHz To 8 GHz
E5055A
Signal Analyzer
The Keysight E5055A SSA-X signal source analyzer provides precise and accurate measurements in one box. Comprehensive and versatile, this solution evaluates the phase noise and other relevant parameters for RF signals up to 8 GHz. Flexible measurement settings and a modern user interface improve measurement efficiency, while application support through software expands measurement coverage to meet new requirements.
-
Product
Variable Gain High Speed Linear Amplifier
F30PV
-
The F30PV is a very fast general purpose linear amplifier having a variable amplification of 0-10 times and capable of bipolar voltage output of ±35V. Any functiongenerator or arbitrary waveform generatoror any othe signal source can be used as an input device. The amplifier's output is linear from DC up to ca 10 megahertz range. It can be used in a wide range of high speed applications.
-
Product
Planar Doped Barrier Detectors
-
KRYTAR Planar Doped Barrier Detectors are specifically designed for use in today's high-performance microwave instrumentation and systems. KRYTAR detectors are designed for such applications as power measurements, analyzing radar performance, leveling pulsed signal sources, AM noise measurements, system monitoring and pulsed RF measurements in ultra-broadband and mm-Wave applications.
-
Product
All-In-One Infotainment RF Signal Source
AST-1000
-
The software-defined AST-1000 is powered by Averna’s RF and test expertise, enabling you to generate all common radio signals (e.g., AM/FM, HD Radio and Sirius/XM), digital video signals (e.g., ATSC, CMMB and DVB-T2), and simulate all common GNSS signals (e.g., BeiDou, Galileo and GPS).
-
Product
PXIe Vector Network Analyzer RF Distributor
M9340A
Vector Network Analyzer
The M9340A PXIe vector network analyzer RF distributor is used in the M9485A PXIe multiport vector network analyzer. The module distributes the source and local signals from the source modules to the receivers.
-
Product
Source Phase Control
S97088B
-
The S97088B allows users to set calibrated, arbitrary phase differences between two signal sources running on the P50xxA Streamline VNAs.
-
Product
Programmable Step Attenuator DC~50GHz, 0~115dB Att.
-
The programmable step attenuator achieves step attenuation over a wide frequency band. It features high attenuation accuracy, excellent repeatability, low insertion loss, and long service life. Its primary applications include controlling the amplitude of signals entering systems, regulating output signal power in systems, and adjusting impedance matching between signal sources and loads. It is widely used in various broadband spectrum analyzers, broadband vector network analyzers, broadband synthesized signal sources, noise figure test sets, and diverse microwave automatic test systems.
-
Product
9kHz to 20/40GHz Signal Generator
CSG Series
-
Corech Microwave’s CSG series of Compact Microwave Signal Generators（Signal Source）operate from 9kHz to 20GHz / 40GHz. It offers high dynamic output power -120 to +17dBm, ultra low phase noise: -105dBc/Hz@10KHz, low harmonics and spurious. These exceptional performances make CSG9K20GA / CSG9K40GA an ideal choice for many test and measurement applications, including Semiconductor, Quantum Technology, Radar and Communication etc.
-
Product
256 GSa/s Arbitrary Waveform Generator
M8199B
Arbitrary Waveform Generator
The M8199B arbitrary waveform generator (AWG) provides R&D engineers with a high-performance arbitrary signal source, enabling design development at 160 GBaud and above. The M8199B AWG enables up to 8 synchronized channels at 256 GSa/s with nominal analog bandwidth exceeding 80 GHz. With integrated frequency and phase response calibration for clean output signals, the M8199B simplifies your test setup.
-
Product
Comb Generator
CG 50/500
-
The main application of Conducted Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble conducted measurements using an ISN.reference signal source Noise Generators Signal Generators
-
Product
LINEAR AMPLIFIERS
F-series
-
The F-series amplifiers are designed to extend the output range of low voltage signal sources. They are general purpose devices with a very low output impedance, very fast response and high current. The output is linear from DC up to few megahertz range.
-
Product
RF Signal Generator
-
RF Lambda’s RF signal generators are wideband DDS driven signal sources in a variety of frequency ranges. They offer extremely fine frequency step size and low phase noise as well as output level control. They are easy to configure with the included GUI and USB interface. They are AC powered for convenience.
-
Product
Broadband Threshold Detectors
-
KRYTAR's All NEW Broadband Threshold Detectors are hermetically sealed for high reliability and are specifically designed for use in today's high-performance microwave instrumentation and systems. KRYTAR detectors are designed for such applications as power measurements, analyzing radar performance, leveling pulsed signal sources, AM noise measurements, system monitoring and pulsed RF measurements in ultra-broadband and mm-Wave applications.
-
Product
2 Channels, 28-115 Vrms, 47 Hz-2.5 kHz (max. range) programmable
AC3
-
The module is used to provide an AC signal source when a secondary reference source other than the optional on-board reference module is required. The modules are programmable for full range voltage outputs from 2 to 115 VAC, and frequency from 47 Hz to 10 kHz.
-
Product
NI-9231, 8-Channel, 51.2 kS/s/channel, -5 V to 5 V, C Series Sound and Vibration Input Module
783610-01
Sound and Vibration
8-Channel, 51.2 kS/s/channel, -5 V to 5 V, C Series Sound and Vibration Input Module - The NI-9231 is a high-density sound and vibration module that can measure signals from integrated electronic piezoelectric (IEPE) and non-IEPE sensors such as accelerometers, tachometers, and proximity probes. It can perform the high dynamic range measurements necessary for modern measurement microphones and accelerometers and features simultaneous sampling. The NI-9231 incorporates both a TEDS input path and 2 mA of IEPE signal excitation source that can be turned on and off, removing the need for external sensor power and reducing the complexity of the data acquisition system.
-
Product
Directional Detectors
-
KRYTAR offers the industry's widest selection of Directional Detectors specifically designed for use in today's high-performance microwave instrumentation and systems. KRYTAR detectors are designed for such applications as power measurements, analyzing radar performance, leveling pulsed signal sources, AM noise measurements, system monitoring and pulsed RF measurements in ultra-broadband and mm-Wave applications. Complete engineering services for custom designs that meet or exceed critical performance and/or packaging specifications are available.
-
Product
Beacon Transmitters
-
Is a radio beacon, whose purpose is the investigation of the propagation of radio signals. Most radio propagation beacons use amateur radio frequencies. They can be found on LF, MF, HF, VHF, UHF, and microwave frequencies. Microwave beacons are also used as signal sources to test and calibrate antennas and receivers
-
Product
RF And Microwave Signal Generation And Analysis
-
The need for microwave test and measurement technology is even more urgent than the need for microwave equipment itself. Therefore, Shengbo Technology is relying on its own research and development capabilities to strive to become one of the comprehensive microwave test and measurement equipment suppliers. We provide a wide range of RF microwave test products, including a good-quality full-band broadband up-down converter . You can provide 2GHz real-time bandwidth signal up-down conversion function in the frequency range of 0.1 ~ 40 + GHz. With our channel simulator , we Became the first company in the world to provide channel analog solutions in such a wide range of broadband signals. At the same time, we are also an innovativesupplier of noise sources and multi-channel microwave signal sources in the industry.
-
Product
Microwave Downconverter, 3 GHz to 26.5 or 110 GHz
E5053A
Downconverter
The E5053A microwave downconverter is designed to operate with the E5052A/B signal source analyzer (SSA). When configured with the E5053A microwave downconverter, the E5052A/B SSA offers exceptional phase noise sensitivity up to 26.5 GHz. Additionally, combining a pair of 11970 series harmonic mixers offers the phase noise measurement up to 110 GHz.
-
Product
Field Strength Meters
-
The FSM series of field strength meters will measure the strength of a RF signal appearing at its input from +20 dBm to -110 dBm for wide bandwidth models and +10 dBm to -120 dBm for narrow bandwidth models. The RF strength will be displayed on an LCD display to an accuracy of ±3 dB over the entire 130 dB dynamic range. A matching field signal generator is also available to act as a signal source for propagation studies.
-
Product
20GHz 30dBm RF Signal Amplifier
A10200
-
Model A10200 is an ultra-small footprint, ultra wideband, high power amplifier designed for high frequency, high power, signal amplification. With an ultra high bandwidth of almost 20GHz and up to +28dBm power into 50 ohms, the A10200 is the ideal complimentary amplifier to any signal source that needs an extended power boost for demanding applications.
-
Product
High Voltage, High Current Linear Amplifier
P100
-
The P100 is a general purpose linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±50V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device.
