Signal Sources
Instrument that provides a stimulus signal (waveform). (www.tek.com)
See Also: Signal, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
Product
PXI-5651, 3.3 GHz RF Signal Generator
779670-01
Signal Generator
3.3 GHz PXI RF Analog Signal Generator—The PXI‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
VXG Vector Signal Generator
M9484C
Vector Signal Generator
The M9484C VXG is the industry’s first dual-channel vector signal generator capable of generating signals up to 54 GHz with 2.5 GHz of modulation bandwidth per channel. The VXG vector signal generator helps you deliver the next frontier of wireless technology such as 5G and satellite communications with a fully integrated, calibrated, and synchronized solution.
-
Product
Calibration Sources
-
Up to an absolute accuracy of 60 MHz standard HighFinesse Wavelength Meters feature auto-calibration by integrated calibration sources. This way highest accuracy and stability of measurements with our wavemeters is guaranteed.
-
Product
Power Sources
MS-Series
-
The MS-Series Power Sources are high performance, high efficiency, AC to AC converters. Rugged powerful output provides up to 350 amps of pulse current for driving non-linear loads.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, 22-28 AWG, Crimp, 30µ" Au
610138216
Signal Contact (Receiver)
*Please note: The difference between this p/n and 610138116 is the amount of gold plating. See below.P/n 610138116- 50µ" AuP/n 610138216- 30µ" AuPrimary mating contact 610138109. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BeCuContact Plating 30µ" Au over 100µ" NiContact Termination CrimpCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force(lbs) 0.24
-
Product
Power Sources
GF303
-
Beijing GFUVE Electronics Co.,Ltd.
GF303 Program-controlled three phase AC standard power source is a high precision three phase AC standard current source and AC standard voltage source.
-
Product
Light Sources
-
Bentham's range of light sources has evolved to suit the requirements of our systems and their users and now offers single or multiple sources from 200nm to 40m:
-
Product
MXG Vector Signal Generator
N5186A
Vector Signal Generator
Compact, four-channel vector signal generator capable of signal generation up to 8.5 GHz with 960 MHz of modulation bandwidth per channel
-
Product
Blackbody Sources
Hyperion R Model 982
-
The Hyperion R Calibration Bath comprises a blackbody cavity for calibration of infrared thermometers. An important factor is that its operation range includes ambient temperature, which is a difficult radiation point to achieve.
-
Product
Light Sources
-
For applications such as transmission, absorption, and reflection, illumination sources are needed. Avantes offers a wide range of different types of light sources, to suit your specific application needs. An overview of the different types of light sources can be found below.
-
Product
Retractable Sources
-
Veeco’s retractable sources address fundamental limitations of MBE, including source capacity, source removal for maintenance and system uptime. The retractable source allows an individual source to be withdrawn and isolated from the growth environment with the source gate valve and then removed without venting the entire chamber.
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781426-03
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
Light Sources
-
Fiber optic light sources are a low-cost way to analyze and identify accurate fiber optic readings, while certifying optical fiber. Receive the ability to measure fiber optic light continuity, loss, and quality of the signal.
-
Product
Source And Measure WiFi And Bluetooth Signals
IQview
-
The LitePoint IQview® simplifies WiFi and Bluetooth® device development with powerful tools to both source and measure WiFi and Bluetooth signals and analysis capabilities providing insight into device behavior. The IQview offers seamless compatibility with the IQflex® manufacturing solution enabling test software developed on the IQview to run on the IQflex platform widely deployed in manufacturing environments.
-
Product
Power Source
SP560
-
Clary's SP 560 is a 400W/560VA power source built for electronics equipment in IT, traffic and security applications, delivering constant, conditioned, regenerated AC power. It protects equipment from being disrupted, degraded or damaged due to harmful power events. Clary power conditioning completely isolates the cabinet from utility power enabling error-free operation during surges, sags, spikes, and other power anomalies. With an optional battery pack, the SP560 system operates as an On-Line, Double-Conversion UPS, extending the reliability of the cabinet's electronics during utility power failures (black-outs).
-
Product
PXIe-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
780587-12
Signal Module
PXIe, 7-Channel, 10 A PXI Signal Insertion Switch Module—The PXIe‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
Product
Signal Generator
8002
-
25C, hysteresis eliminated. To within 10 MHz of the final frequency. Normal switching mode, SSB phase noise will be degraded in the fast switching mode.
-
Product
PXIe-5820, 500 MHz, 1 GHz I/Q Bandwidth, Baseband PXI Vector Signal Transceiver
783967-01
Vector Signal Transceiver
500 MHz, 1 GHz I/Q Bandwidth, Baseband PXI Vector Signal Transceiver—The PXIe‑5820 is the baseband model of the second-generation vector signal transceiver (VST) with 1 GHz of complex I/Q bandwidth. It combines a wideband I/Q digitizer, wideband I/Q arbitrary waveform generator, and high-performance user-programmable FPGA in a single 2-slot PXI Express module. You can use the VST for a variety of applications including baseband I/Q test of wireless and cellular chipsets; envelope tracking of digitally predistorted waveforms for power amplifiers; and the generation and analysis of new wireless standards such as 5G, 802.11ax, and LTE-Advanced Pro.
-
Product
Signal, Contact, ITA, TriPaddle, 10 Amp, 14-18 AWG, Crimp/Solder
610110172
Signal Contact (ITA)
Primary use in CASS applications.
-
Product
Signal Generators
-
Whether the BPSG generators with their precisely generated RF signals for testing EMC shielding and EMI/RFI measurements, or the brand new SPECTRAN V6 VSG vector signal generators with a frequency range of 10 MHz - 6 GHz and a large number of modulation types, the Aaronia signal generators impress with their quality and price.
-
Product
Signal Generator
SGA3
-
The C.Scope SGA3 is an affordable Signal Generator designed for use alongside a CXL3 or DXL3 Cable Avoidance Tool to make the task of cable avoidance far more effective.
-
Product
AC Source
AMF
-
The Intepro AMF Series is a complete line of single and three phase, 400Hz AC Frequency Converter products. With Power levels ranging from 6kVA up to 300kVA, the AMF series of frequency converter products are the ideal and cost effective solutions for precise frequency conversion in all avionics and higher frequency electronic applications. Power and frequency conversion is supplied by state-of-the-art IGBT pulse-width-modulated power amplifiers resulting in highly efficient power conversion, compact design and maximized performance with minimum downtime.
-
Product
Visible Laser Source
VLS35
-
The KD Optics VLS-35 is a pocket sized, visible source used for testing fibre optic cable installations. The unit is pocket sized with a long battery life from a PP3 battery, making it ideal for local fault finding and continuity checking of fibres.
-
Product
High-Power Noise Sources
-
These modules not only contain the noise diode circuitry, but also gain stages to boost the output power. While lower frequencies (under 2 GHz) are most common, Mercury produces powerful amplified noise modules up to 18 GHz. Noise modules are available in coaxial, surface mount and pin type construction. TTL control options are available.
-
Product
Light Source Colorimeter
CX-HP2
-
Shenzhen Chuangxin Instruments Co., Ltd.
Light source colorimeter is a newly developed pocket colorimeter, adopting advanced spectrometer and microprocessor technology. It makes traditional laboratory instrument available for the production on-line quality acceptance, thus greatly improve the efficiency of fluorescent lamp, CFL, LED manufacturing.
-
Product
UXA Signal Analyzer, Multi-touch, 3 Hz to 110 GHz
N9041B
Signal Analyzer
Characterize challenging millimeter-wave signals: 5G, 802.11, satellite, radarMake continuous sweeps up to 110 GHzCapture lower-level spurious signals with DANL as low as -150 dBm/Hz (> 50 GHz)Simplify analysis of the latest wideband signals: 1 GHz fully-integrated instantaneous bandwidth; 5 GHz with external IF output
-
Product
Noise Sources
NC1128A
-
This noise source by Noisecom produces white Gaussian noise up to +13 dBm. It contains a hermetically packaged noise diode that has been pre-selected for special performance characteristics. This module is ideal for many different applications including CATV, Secure communications, Jamming systems, OC-192 Testing, EW & EC.
-
Product
Signal Injectors
-
Ideal high performance, low noise compliment to your Circuit Sleuth Frequency Response Analyzer. An injection transformer is used to couple an excitation signal from a frequency source into the feedback loop of a control system. This allows loop gain and phase vs. frequency to be measured, with the loop closed, thus characterizing the stability of the system.
-
Product
VXG Microwave Signal Generator
M9384B
Microwave Signal Generator
The M9384B VXG is the industry's first dual-channel microwave signal generators capable of up to 44 GHz signals.
-
Product
Long Light Source
LM-A
-
The long light source is compatible with the LM-101 or the LMC-20. The light is supplied with a 50 watt tungsten halogen convection cooled light source which provides suffcient energy for use with narrow band pass filters or monochronomators in the wave length range of .35 to 2.5 microns. The light beam is chopped at 200 hz by a quiet, vibration free, synchronous motor. The housing also contains a secondary LED light source and detector for synchronization of the amplifier, plus an electro-mechanical shutter to block the light output when the instrument is zeroed. An internal collimating lens produces a narrow beam (<1") so the LM-A can be used in bell-jar and large coating systems.
