-
Product
DH Series Tip - CrossSync PHY PCIe5 CEM x16
DH-CSPHY-PCIE5-CEMX16
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Bench/System Multi-Range DC Power Supply With Digital Control, 3 Or 4 Outputs, 315 To 420W With/without Remote Interfaces
MX Series
-
Three or four high performance outputs each with full functionalityRange switching gives variable voltage/current combinationsShared power mode provides double power from a single outputLow output noise and ripple via linear final regulationHigh setting resolution of up to 1mV and 0.1mAVariable OVP and OCP trips on all outputs50 setting memories per output plus 50 linked memoriesSelectable voltage tracking (isolated tracking)Selectable current meter averagingSwitchable remote sense capabilityGraphic LCD provides simultaneous output meteringNumeric or spin-wheel control of all parametersIndividual or combined output on/off control with programmable delay sequencing.3U half-rack case for bench or rack mounting (4U rack kit accessory available)RS-232, USB and LAN (LXI) interfaces (P models)GPIB option (P models only)Duplicate power & sense terminals at rear (P models)
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 2 Channels (Single Ended) or 2 Channels (Differential)
M2P.5961-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
SSD
CFAST-B-XXG-SI
-
The CFAST-B-XXG-SI is a USA-made product line of Industrial SLC-based CFast memory cards. These small form factor CFast cards provide SATA level performance while featuring robust features needed for industrial applications. These cards contain a locked-down Bill of Materials to ensure consistent product performance and future compatibility.
-
Product
Network Sensor Interface for USB Pressure Transducers
SI314
-
The Validyne model SI314 is a network interface that connects our model P61 USB pressure Transducer to your smart phone or network web browser. The SI314 supports Ethernet and Wi-Fi connections and will display current pressure readings and transducer status on any web browser or via smart phone. The SI314 also displays the transducer temperature, date of calibration, model and serial numbers and these can be viewed wirelessly or by Ethernet connection. The SI314 makes your P61 accessible from anywhere in the world. Data logging of pressure data is configured via a web browser or smart phone and readings may be stored once per minute to once per hour. A thumb drive or memory card collects the data in comma separated file format(csv) for download to your computer. The data may also be accessed via the network. A graph of the data is also generated on request. A Twitter function allows pressure data to be tweeted from the SI314 at user-defined intervals. The transducer zero and span calibration adjustments are password protected and operated via browser buttons. No potentiometer adjustments are required to calibrate the P61 transducer. Contact our Sales Department for a link to the Demo!
-
Product
PCIe 14 Bit High Speed Digitizer - 400 MS/s on 2 Channels
M4I.4480-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
16 or 32 channel Digital to Analog Converter
LS-71-P
-
The LS-71P PCI D/A Converter (DAC) board provides high speed analog outputs of PCM decommutated data allowing real time data displays using strip chart recorders or similar devices. The LS-71-P board is designed to be used in conjunction with the Lumistar LS-50-P Multifunction PCM Decommutator boards and uses an over-the-top communication bus directly from the decom to the DAC to avoid any glitches in the analog outputs due to PCI bus activity. Direct “mailbox” type access is also provided to allow the user to send information through the PCI bus to the DACs. The DAC board design allows 2 LS-50-D Multifunction decom boards to be used with a single DAC board allowing tagged data from either data stream to be directed to any DAC channel. An optional LS-71-DB Word Selector Daughterboard allows two additional data streams to be monitored with the ability to select channels from 4 data streams to be displayed on any DAC channel. The design incorporates an extremely large memory (more than 200,000 16-bit words) used as a lookup table allowing linear or non-linear EUconversions with constant delay regardless of the number of polynomial coefficients required. Standard product supports a single decom, however, dual decom support is available as an option.
-
Product
Auto Wire Integrated Tester Series
LX-1024A+
-
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface,．·Up to 1500Vdc/1000Vac Test Voltage ,．·1024 Max. Test Points ,(Max of all series)．·500 Max Files Memory,support USB or PC unlimited expansion,．·Using Embedded Linux operating system，．·Adopted high resolution colour 640*480 TFT LCD ,．·Large 320×240 LCD display ,．·Instant test time :0-60s , optional adjustment.．·Providing Single-End ,Multi-segment ,Standard ,and Spot test of wire.．·Auto Scan and Auto Pin Search ,．·The system provides advanced instant open-circuit, short-circuit, continuity test,．·Intermittent Conductance Test,．·Intermittent Open/Short Test ,
-
Product
PCIe VU13P UltraScale+TM With Massive Optical I/O
PCI597
-
The PCI597 is based on the Xilinx VU13P UltraScale+TM FPGA, which provides over 12,000 DSP slices, 360 Mb of UltraRAM and 3,780K logic cells. The Unit provides active cooling of the FPGA making it appropriate for power-hungry applications or those requiring temperature stability for good performance. The FPGA has interface to DDR4 memory channels (single bank of 64-bit wide, 16 GB). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host.
-
Product
PXIe-5162, 1.5 GHz, 5 GS/s, 10-Bit, 2GB mem, Oscilloscope
782622-15
Oscilloscope
PXIe, 1.5 GHz, 5 GS/s, 10-Bit PXI Oscilloscope—The PXIe-5162 high-speed oscilloscope device has two or four channels that sample at up to 5 GS/s with flexible settings for coupling, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 1.5 GHz of analog bandwidth and flexible measurement configurations.
-
Product
Fanless Desktop Network Appliance Platform With Intel® Celeron® Processor N3350 1.10 GHz And 3 GbE LANs
NA345E
-
The fanless NA345E adopts the low-power consumption Intel® Celeron® processor N3350 (codename: Apollo Lake). It aims to provide small business and SOHO customers an energy-saving and cost-effective network appliance for solutions in VPN, content filtering, UTM, network security gateway, and firewall. The desktop NA345E supports one non-ECC DDR3L-1866 SO-DIMM socket providing system memory of up to 8GB; moreover, it offers one mSATA for storage. It is equipped with three 10/100/1000 Mbps LAN ports (Intel® i211 Ethernet controller). The network appliance platform also has two USB 3.0 ports and an RJ-type serial console port. The system features a watchdog timer for reliable operation. Additionally, it supports Linux operating system.
-
Product
Monitor / Annunciator
RTP-1
-
The RTP-1 Monitor is a general purpose annunciator. Designed for 19 “ rack installations, the RTP-1 is complete with a noise immune filter. The ten point RTP-1 features latching memory. Easy to install and easy to operate, this low power monitor has front panel plug-in replaceable LEDs for indication and a single system Test and Reset buttons.
-
Product
600MM 24In Digital Level Bevel Gauge w/ LCD Backlight Screen, Level Bubbles, IP54 Standards
DL406
-
Advance Plus Trading Co., Ltd.
Model Number: DL406 Key Specifications/Special Features: 600MM 24INCH Digital Level with level bubbles,LCD bright backlight display, IP54 standards 1. 600mm 24 inch level with 2 bubbles, 600*28*64mm（L*W*H）, net weight: 520g;2. Resolution: 0.05°;3. Horizontal level measuring range: 0 to 360°;4. Accuracy: ±0.3°;5. Measures angle in degrees, IN/FT, mm/m, % slope or pitch;6. Audible tone at level, plump and setting angle;7. Automatic shut-off after 3 minutes;8. Backlight LCD;9. Self checking accuracy;10. Self calibration;11. Hold-function to freeze the measurement;12. Memory recall (9 measurements);13.Handshank design, easy to take and use;14. 2pcs high accuracy horizontal & vertical bubbles, clearly to check;15. Operated by DC 3V (2*LR03 AAA 1.5V batteries, not included); 16. IP54 waterproof & dusyproof industrial standard.
-
Product
Multibus Ethernet Card
MS 1750
-
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz- SDRAM Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Multibus Interface- Serial Interfaces: Up to four external UARTs- CAN 2.0B controller- Three I2C ports- Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements
-
Product
T3DSO1000HD Series Oscilloscopes
T3DSO1000HD Series
Oscilloscope
The Teledyne Test Tools T3DSO1000HD Oscilloscopes feature four channel bench models with analog bandwidth options of 100 MHz and 200 MHz each with 12 bits of vertical resolution. Each model offers a maximum sample rate of up to 2 GSa/s sample rate and a maximum memory up to 100 Mpts. The series comes with all serial data trigger & decode options as standard alongside Power Analysis and Bode Plot capabilities.
-
Product
SMARC V1.0 SoM Evaluation Kit With Quad/DualLite 800 MHz (Industrial) SoC,1GB Memory, 4GB EMMC, Gigabit Ethernet, Audio, CAN, MIPI And PCAM
SCM120-120-EVK
-
*Ultra low power consumption Cortex™-A9*2 CAN 2.0B*24-bit TTL LCD*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Open GL ES2.0*Linux3.0.35/Android 4.3*Audio
-
Product
Live Recorder
-
Live Recorder allows Linux programs to make a detailed recording of themselves while they are running, and to load the resulting Undo Recording in a specially configured UndoDB - our reversible debugger for Linux. An Undo Recording allows UndoDB to completely reconstruct everything a program has done, including every memory access and every instruction executed. By using Live Recorder, developers can debug an exact copy of the original program''s execution, allowing them to track down bugs without needing to reproduce them in-house, write test cases or make time-consuming visits to customer sites.
-
Product
SKYbolt II 6U VME 8-Slot
-
Delivering performance of 16 GFLOPS the SKYbolt II 6U VME solution adds intelligent support for system services and high-performance data transfers as the carrier board for the Merlin daughtercard which contains the compute processors, I/O interfaces, and global memory
-
Product
T3DSO4000L-HD Series Oscilloscopes
T3DSO4000L-HD Series
Oscilloscope
The Teledyne Test Tools T3DSO4000L-HD Oscilloscopes feature four and eight channel low profile models all with 12 bits of vertical resolution. With analog bandwidth options of 500 MHz, 1 GHz and 2 GHz. Each model offers a maximum sample rate of 10 GSa/s with ESR per channel, and a maximum memory depth of 500 Mpts in single channel mode. The T3DSO4000L-HD series is ideal for ATE systems as well as other automated applications.
-
Product
Embedded MXM GPU Modules with NVIDIA® Quadro® Embedded P2000
EGX-MXM-P2000
Graphics Card
The EGX-MXM-P2000 features advanced NVIDIA Quadro GPU with NVIDIA Pascal™ Architecture technology in MXM 3.1 Type A form factor. The EGX-MXM-P2000 has 768 NVIDIA CUDA cores and a peak single-precision floating-point performance of 2.3 TFLOPS. The EGX-MXM-P2000 has 4GB of GDDR5 memory and supports NVIDIA GPUDirect™ RDMA which helps increase data throughput by up to 80% and consequently system responsiveness by up to 60%*. Additionally, 4 UHD display outputs and an extended operating temperature range of -40°C to 85°C are supported. The embedded graphics product is suitable for mission-critical harshenvironment edge computing applications with size, weight, and power (SWaP) and network connectivity constraints.
-
Product
QorIQ P204x Processor AMC
AMC711
-
The AMC711 is a Processor AMC (PrAMC) in a single module, mid size AdvancedMC™ (AMC) form factor based on the Freescale P2040 or P2041. The module follows the AMC.1 and AMC.2 specifications. The PCIe interface is configurable as Host or Agent mode and it interfaces as dual x4 (ports 4-7 and 8-11). The P2041 has option to have ports 8-11 as XAUI (10GbE). The AMC711 has up to 8GBytes of DDR-III memory with ECC.
-
Product
Oscilloscope: 1.5 GHz, 4 Analog Channels
DSOX4154G
Oscilloscope
12.1-inch display, capacitive touch screen technology, InfiniiScan Zone touch triggering, 1-million-waveforms/sec update rate, MegaZoom IV smart memory technology, and standard segmented memory
-
Product
Rebar Corrosion Rate Determination System
Gecor 6
-
Measures the rate of corrosion and other parameters of rebars. The Gecor 6 utilizes the polarization resistance technique to establish the corrosion rate. This is a quantitative measure of the amount of steel oxidizing at the time of measurement. Up to 100 readings can be stored in memory for later uploading to a Personal Computer.
-
Product
Embedded Development Kit
TySOM
-
The TySOM Embedded Development Kit is for the embedded designer who needs a high-performance RTL simulator/debugger for their embedded applications such as IoT, Factory Automation, UAV and Automotive. The kit includes Riviera-PRO Advanced Verification Platform and a Xilinx Zynq development board that contains single Zynq chip (FPGA + Dual ARM Cortex-A9), memories (DDR3, uSD), communication interfaces (miniPCIe, Ethernet, USB, Pmod, JTAG) and multimedia interfaces (HDMI, audio, CMOS camera).
-
Product
DCU Gateway Solutions
-
Signals & Systems India Private Limited
SANDS DCU is an ideal gateway solution for the Energy Management System (EnMS). It provides connectivity to the cloud apart from data collection, local data storage. DCU is based on ARM Cortex-A5 processor having 512MB of DDR2 memory and expandable NAND Flash memory upto 2GB. Edge / Sensor data can be stored locally using the on-board SD card option. The cloud interface is LTE with 2G/3G fall back.
-
Product
Memory Burn-in Tester
B6700 Series
-
B6700 can test as many as 48 burn-in boards in parallel at speeds up to 10 MHz, which helps memory suppliers get their newest products to market faster while also reducing testing costs. An original high performance chamber improves yield by assuring high temperature accuracy while generating high temperature. It also shortens the temperature rise and fall time which leads to shortening the test time.
-
Product
3U CompactPCI Quad-Core Intel Atom® Processor X Series Blade
cPCI-3630
Processor Blade
The ADLINK cPCI-3630 Series is a 3U CompactPCI® 2.0 processor blade featuring the 64-bit Intel Atom® Processor X Series SoC (formerly Apollo Lake I) and soldered DDR3L-1600 MHz ECC memory up to 8GB.
-
Product
Super Phosphor Oscilloscopes
SDS2000X-E Series
-
The SDS2000X-E series employs a new generation of SPO technology. With its excellent signal fidelity, background noise is lower than similar products in the industry. It has a minimum vertical input range of 500 uV/div, an innovative digital trigger system with high sensitivity and low jitter, and a waveform capture rate of 400,000 frames/sec (sequence mode). It also employs a 256-level intensity grading display function and a color temperature display mode not found in other models in this class. Siglent’s newest oscilloscope offering supports multiple powerful triggering modes including serial bus triggering and decoding. History waveform recording and sequential triggering allow for extended waveform records to be captured, stored, and analyzed. Also included is the deep memory FFT. This math function uses upto 1 M samples for the FFT calculation, providing the SDS2000X-E with very high frequency resolution. The hardware co-processor executes true fast measurement and math to all of 28M sample points so that there is minimal distortion on analysis. It also supports searching and navigating, on-screen Bode plot, 16 channel digital /MSO (optional), an external USB powered 25 MHz AWG function generator module (option), a USB WIFI adapter for wireless control and monitoring (option), and an embedded application that allows remote control via web browser. The features and high-performance of the SDS2000X-E oscilloscopes cannot be matched else anywhere at this price.
-
Product
COM Express Type 10 Mini Module With Intel® Pentium® & Celeron® N3000 Series Processors
CEM300
-
The CEM300, a COM Express® Type 10 module, supports Intel® Pentium® N3710 and Celeron® N3160/N3060 quad-core/dual-core processors (codename: Braswell) with support for 4 GB DDR3L memory onboard. Integrated with Intel® Gen 8 graphics, the COM Express® Type 10 computer-on-module provides excellent graphic performance including support for DirectX 11.1, OpenGL 4.2, and 3D features and resolution up to 4K (3840 x 2160 @ 30 Hz). The ultra-small mini module comes with 4 to 6 watts low power consumption, and provides wide range voltage power input of 4.75V to 20V for harsh industrial environments. The Axiomtek CEM300 is ideal for IoT-connected industrial controls, medical imaging, retail equipment, MMK (Multi Media Kiosk), industrial gateway, automation and POS terminals related applications.
-
Product
Analyzer Probes
-
The following probes are available for the MA51x0 and MA41x0 series analyzers. These probes are designed for low-voltage and high-speed midbus probing or probing with an interposer. The following JEDEC memory standards are widely used by these probes: DDR5 (JESD79-5), DDR4 (JESD79-4), DDR3 (JESD79-3), LPDDR5 & LPDDR5X (JESD209-5), LPDDR4 & LPDDR4X (JESD209-4), and LPDDR3 (JESD209-3).
