-
product
D/A Converters
Renesas' high-speed, low-power, digital-to-analog data converters (DAC) are ideal for communication systems, medical/test instrumentation and equipment, and video applications.
-
product
4K HD Video Converter with CVBS out, 4K 30FPS Output
M-CVT-HD4
Fuzhou Metricu Technology Co Ltd
Support up to AHD 8MP, TVI 8MP, CVI 8MP testAuto recognition 720P/1080P/3MP/4MP/5MP/8MP resolutionIndicator visual display input resolutionOne channel AHD/TVI/CVI/CVBS loop out, CVBS out
-
product
Power Supplies
A power supply is a component that supplies power to at least one electric load. Typically, it converts one type of electrical power to another, but it may also convert a a different form of energy - such as solar, mechanical, or chemical - into electrical energy. A power supply provides components with electric power.
-
product
8-Channel ADC Module
FMC168 – LPC
Sundance Multiprocessor Technology Ltd.
The FMC168 is a digitizer FMC featuring eight ADC channels with 16-bit resolution and 250 Mega samples per second sampling rate per channel. With a flexible clock generation and distribution scheme, the FMC168 allows control on sampling frequency and analog input gain through serial communication with a carrier card. The FMC168 design is based on the TI ADS42LB69 Dual Channel 16-Bit 250 MSPS A/D, is equipped with power supply and temperature monitoring, and offers several power-down modes to switch off unused functions.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K1
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Multi Gas Analyser
OR-703
The OR-703 multi gas analyser expands the capabilities of the PF-300 series gas flow analysers. Its compact ad lightweight housing makes the OR-703 an ideal and integrated solution for the accurate measurement of anesthetic gas concentration.
-
product
Configurable & High Density Signal Transport
VF-9000 Series
Life on a mobile production truck or ENG van means making the most of your surroundings. With limited real estate for technology, our customers need high-density platforms to manage the abundance of signals coming in and going out. MultiDyne’s VF-9000 Series is built for high-pressure sports, news and live event production scenarios, and high-capacity transport requirements between studios and across campuses. The VF-9000 Series is also remarkably intelligent, providing automatic configuration of video inputs and outputs based upon recognizing which VF-9000 SFP modules are added to the frame. Hot-swappable modules establish redundancy to ensure live mission-critical operations are never disrupted, while data transport, video signal regeneration and wavelength shifting add value for users seeking a brute-force, rock-sold signal trunking and fiber transmission solution.
-
product
Quad 3.1 Gsps, 14-bit ADC FMC+
ADF-Q3114
The ADF-Q3114 is a VITA 57.4 compliant FPGA Mezzanine Card (FMC+) that converts four channels of up to 3.1 GHz analog input bandwidth. This digitizer provides unparalleled analog-to-digital conversion capability with the PCIe/VME/ VXS/VPX carrier board of your choice. The ADF-Q3114 is designed to be compatible with AMD FPGA platforms.
-
product
Signal Converters For Temperature Measurement In Direct Drive Motors
EIB 5000 series
*Reduced cabling*Overload protection for direct drive motors*Faster response behavior for excessive temperatures*Greater cost-effectiveness
-
product
16-Channel 250 MHz A/D with Multiband DDC, Kintex UltraScale FPGA - 6U VPX
Model 58132
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- 16 250 MHz 16-bit A/Ds- 16 wideband DDCs (digital downconverters)- 128 multiband DDCs- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2, &3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available
-
product
6-Ch 200 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - 6U VPX
Model 58721
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three or six 200 MHz 16-bit A/Ds- Three or six multiband DDCs- One or two DUCs- Two or four 800 MHz 16-bit D/As- Multiboard programmable beamformer- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Regenerative DC Electronic Load
IT8300 Series
ITECH newly launched IT8300 Regenerative DC Electronic Load, it not only can simulate various load characteristics, but also can feed power back to grid without pollution. IT8300 series unique regenerative function can convert the absorbed DC power into AC power and feed it back to local grid.
-
product
Optical/Electrical Clock Recovery
N1077A
50 MBaud to 32 GBaud data rate range (continuous) on optical and electrical designs Provides standards-compliant clock recovery (CR) for NRZ and PAM-4 data signals Yields flexible, compact, high-sensitivity CR design with an integrated amplified optical-to-electrical (O/E) converter Gain optimal ease-of-use with integrated splitter and bulk optics coupler (Option SMS)
-
product
Narrow Profile Power Supplies
DC-DC Converters
These state-of-the-art DC-DC converters combine excellent regulation and ripple specifications with broad input ranges, and they are available in a large selection of output voltages and current ratings. Accessory mounting kits permit easy installation on a vertical panel, wall or on a DIN rail.
-
product
AC-DC Power Supplies
Samlex America, Inc Power Supplies
Power supplies convert Alternating Current (AC) into Direct Current (DC). There is a wide choice of input and output voltages and power capacity to meet your specific requirements. Samlex Power supplies spectrum includes:
-
product
SKYbolt II 9U VME
Delivering 64 GFLOPS of performance when fully populated, the SKYbolt II 9U VME motherboard is the foundation of SKY's VME solution, adding intelligent support for system services and high-performance data transfers to the carrier board for SKY's Merlin daughtercard containing compute processors, I/O interfaces, and global memory. A separate System Processor resident on the motherboard handles system overhead functions that would otherwise burden the compute processors.
-
product
RR Signal Source
Behlman’s RR series of Railroad Signal Sources and Frequency Converters are low cost, highly reliable, switch mode units built for Railroad Signaling. The RR series can be supplied with any single or three-phase input and outputs a clean, regulated AC signal at a precise frequency from 25 Hz to 250 Hz. These rugged signal sources are built to support the rigors of operating in the harsh environment of Railroad signaling equipment.
-
product
Isolated DC-DC Converters
power supplies that convert one DC voltage level to another while maintaining galvanic isolation between the input and output circuits.
-
product
USB-to-Serial Cable Converter
This cable is the solution for users who want to communicate with GE Multilin IEDs via PCs that have USB communication ports. Using this cable is quick and easy. Simply install the cable driver on your PC, plug in the cable and you are ready to communicate.
-
product
2-Ch 1 GHz A/D and D/A with Virtex-7 FPGA - 6U VPX
Model 58730
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One or two 1 GHz 12-bit A/D- One or two 1 GHz 16-bit D/A- 4 or 8 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- Dual-µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
1GS/s 75MHz BW USB Modular Scope Pen
USBscope50
USBscope50 marks a new era in ultra portable modular instrumentation for the PC or notebook. Using a USB1.1 or USB2.0 port on the host computer, USBscope50 offers the best of all worlds for converting your PC into a powerful diagnostic tool: tiny size, low power, low cost, modularity and high performance.
-
product
Data Concentration And Protocol Conversion
Schweitzer Engineering Laboratories, Inc.
Communicate and collect data from IEDs, exchange and convert data between protocols, and execute output logic for real-time control with SEL automation and communications solutions.
-
product
100-250V AC/DC Voltage Tester
7321
Peaceful Thriving Enterprise Co Ltd
Voltage Tester is designed to make reliable, safe and easy testing of voltage, with standard handhold to make it easy to use. There are visibility neon to offer clear indication and adding test lead holders spaced to fit the outlet. These features combined with a durable ABS housing and with UL and cUL approvals make the choice of professionals.
-
product
Fuel Cells Testing
A fuel cell is a critical device that can convert the chemical energy in liquid fuels into electrical energy. It is widely used in various industrial applications for power generation and transportation. The development and installation of fuel cells for use in portable and stationary applications is expected to help solve worldwide fuel-energy problems.
-
product
Trip Amplifiers
Datexel manufacture a large range of Trip Amplifiers and Process Limit Alarms that accept universal inputs and provide either relays or NPN or PNP transistor outputs. The DAT5028 is also an isolated signal converter and has a local display with up to 4 relays and is DIP switch programmable. The inputs can be Thermocouples, RTD, mV, mA, Resistance, Potentiometers or Voltage. They can be supplied fully configured set up by PC or DIP switches. The DAT5024 is a trip Amplifier / Temperature limit alarm for RTD's, Thermocouples, Voltage, Resistance and Current with the option of 1 or 2 relay outputs hysteresis and delay timers. The DAT5024 E range is an economical choice with DIP Switch programmable for voltage or current input. Either 1 relay or 2 relays (SPDT) are available with delay timers.
-
product
PXIe-7862, Kintex-7 325T FPGA, 16-Channel AI, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
786672-01
PXIe, Kintex-7 325T FPGA, 16-Channel AI, 1 MS/s, PXI Multifunction Reconfigurable I/O Module - The PXIe-7862 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of timing and synchronization. With 16 analog input channels connected directly to a Kintex-7 325T FPGA, you have ample space to design applications that require precise timing such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe-7862 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe-7862 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
product
PCI Data Acquisition Boards
AD8-650X2DMA Series - 8 bit, 800MS/s
Model AD8-650X2DMA is similar to the AD8-1250DMA, but contains two simultaneous-sampling A/D channels, each capable of sampling at up to 800 MS/s.
-
product
RF Converters
Typically designed for radar or wideband EMC test applications, our frequency converter modules are designed for the conversion between complex baseband waveforms and higher transmitted frequencies. These modules are ideal for integration with digitising modules.
-
product
F/V Converter
FV-1100
The FV-1100 receives signal from a rotation detector or a similar device and outputs DC current or voltage signal proportional to its frequency. As the fluctuation of the input frequency signal is continuously converted to DC voltage, it is useful for measurement and recording of transient phenomena such as fluctuation of rotating speed, current velocity, frequency.
-
product
Electric Vertical Test Stand
WDW-L series
Jinan Testing Equipment IE Corporation
Electric Vertical Test Stand is a tensile compressive test stand especially designed to match push-pull force gauge. This series pf electric vertical test stand has good stability, wide application range and is convenient to use. The electric vertical test stand has stepless speed-adjusting uniform motion, digital display of the testing speed and converting mode between manual and automatic operation. The vertical test stand is specialized for tension/compression test, insertion/withdraw test, fatigue test and fracture test.
