Audio Test
See Also: Audio Testers, Audio Test Systems
-
Product
Test System
ETS788XL
-
The 50/100 MHz ETS788XL system is the compact protable version of our ETS788. Made with the new high-performance precision components of our Griffin series, this portable powerhouse offers an optional tough road case and ready to go to any test site needed. Just pop off the covers and get started. Whether it's research, Failure Analysis, or single-event effects testing, his powerful member of the HiLevel family takes advantage of all of the tried and true features that have served users so successfully to date.
-
Product
Audio Frequency Transmitter
TG 600
-
Cable fault location with the BAUR TG 600. The TG 600 audio frequency transmitter was designed specifically for the precise location of cable faults and joints using the twist method. The display of the input and output current makes selection of the correct adjustment easier.* High-performance audio frequency transmitter up to 600 VA* Frequency of 2 or 10 kHz, quartz-stabilised (other frequencies on request)* Potential-free output* Impedance adjustment in 8 steps from 0.3 to 300 Ω
-
Product
Transformer Testing
-
Haomai Electric Power Automation Co.,Ltd.
1)Test Standard:IEC60076 & IEEE C57.12.90 2)Voltage ratio measurement of transformer 3)Turns ratio measurement of transformer 4)Group vector measurement of transformer
-
Product
4-Module ICT System, I307x Series 6
E9903G
-
Test efficiency, test system stability, and seamless equipment integration. Keysight’s i3070 Series 6 family provides those improvements built upon a proven technology foundation. With time-tested software, hardware, and programmability, the Series 6 are fully backward compatible with previous systems, and they make highly repeatable measurements.
-
Product
Mixed Signal Test Systems
MTS1020i
-
The MTS-1020i is a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
Product
Relay Test Equipment
ME3000 Series
-
ME3000 is recently developed low-cost oriented relay test equipment, aimed to supply customer cheaper and cost-effective product.
-
Product
2.5mm Test Rod Test Probe Needle
CX-4C
-
Shenzhen Chuangxin Instruments Co., Ltd.
2.5mm test rod test probe needle Used to verify the protection of persons against access to hazardous parts.
-
Product
Dissolution Testing
-
Dissolution testing determines the release rate of an active pharmaceutical ingredient in tablet or capsule form as it dissolves into solution.
-
Product
Load Test Software
TW-3.0
-
The TW-3.0 Load Test software from DLM is a software platform designed to complementDLM’s TW-3.0 range of products within the lifting industry. Used as a tool for assisting therecording of test results and generation of certificates during a load test, the software is able to be loaded onto a Windows PC and accept the output from a TW-3.0 handheld display.
-
Product
TurboFan Test Cells
-
Atec, Inc. is an industry-preferred provider of full scale TurboFan test cell design, construction, maintenance, and refurbishment. Our seasoned aeroengine professionals and comprehensive network of international locations and resources provide our customers with unparalleled expertise and value for their most critical and complex test cell projects.
-
Product
Circuit Breaker Test Equipment
-
DV Power has released a new generation of circuit breaker test equipment for condition assessment of medium and high voltage circuit breakers.Field-portable instruments with standalone or PC controlled functionality, allow performing various tests during circuit breaker manufacturing, commissioning and maintenance stages.Applications supported by the DV Power test equipment include measurements of:Contact resistanceDRM (dynamic resistance measurement)Coil resistance and coil current (IEC 62271-100)Mechanism charging time (IEC 62271-100)Minimum trip voltage (IEC 56, ANSI C37.09)Undervoltage release (IEC 60694)The timing of a circuit breaker’s main, auxiliary and pre-insertion contactsSynchronization between the contactsMotion and velocity“First trip” testThe essential part of a circuit breaker condition assessment is the ability to compare the latest test results with the previous testing. Accordingly, our instruments store measured values and compare them to a manufacturer’s limits. Also, a fingerprint obtained in this way can be used at a later stage as a reference during subsequent measurements. In order to obtain an accurate comparison, the tests need to be performed using identical test parameters. Consequently, any deviation and change in the test results may indicate the circuit breaker condition deterioration. Even more, to overcome this issue, DV-Win enables test plans and graph overlay features.Finally, as a final result of a circuit breaker maintenance process, the DV-Win provides analytical tools and customized report creations.
-
Product
Shock Test Systems
-
Sanwood Environmental Chambers Co ., Ltd.
Is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and collision test, can perform conventional half-sine wave, post-peak sawtooth wave, square wave and other waveform shock tests.
-
Product
Motor/Generator Test Equipment
-
Winding ohmmeters RMO-M series measure winding resistance of inductive test objects such as electrical motors and generators. Motor test or generator test of winding resistance is especially important for early-stage failure detection.RMO-M series instruments generate true DC ripple-free current with automatically regulated measurement and discharge process. Even more, test instruments are portable and enclosed in a metal casing.Applications supported by DV Power motor/generator test equipment include:Winding resistance measurement of generators and electrical motorsResistance measurement of high-current bus bar jointsResistance measurement of cable splicesAll of the above-mentioned measurements are performed with the highest accuracy. The advanced DV-Win PC software enables collecting both numerical and graphical results. These features provide an easier and more efficient analysis. After the test, a DV-Win software generates a test report a single click. Finally, a user can easily customize the report and save it in different formats, such as XLS and PDF.
-
Product
N Test Finger Nail
TF-24 series
-
Are designed to perform tests specified in many standards to determine compliance with safety requirements.
-
Product
Magnetic-Field Test System
MTS-800
-
The MTS-800 is a compact test system for broadband generation and measurement of magnetic fields. Its internal components allow automatic EMC tests according to automotivestandards where high field strength need to be generatedor measured.
-
Product
Lithium Battery Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Lithium battery test chambers are used to simulate various extreme conditions such as crush, impact, penetration, overcharge etc the lithium ion cells and batteries are subjected to during use, transportation, storage and disposal to determine the safety performances, tests including altitude simulation test, thermal test, vibration test, shock test, external short circuit test, impact/crush test, overcharge test, discharge test etc based on UN38.3, IEC62133, UL1642 standards. Applicable to communication products, computer products, consumer electronics, automobile power supplies and so on.
-
Product
Code Test Optimizer
Clover
-
Clover provides the metrics you need to better balance the effort between writing code that does stuff, and code that tests stuff.Clover runs in your IDE or your continuous integration system, and includes test optimization to make your tests run faster, and fail more quickly.
-
Product
Safety Chamber, Hydrostatic Test
9901HTX-36x36x15
-
The 3 ft wide by 3 ft deep Hydrostatic Test Safety Chamber, when combined with one of our pump systems, provides a complete hydrostatic test system for testing hose and assemblies or other components requiring pressure testing.
-
Product
Custom Test & Measurement
-
Delserro Engineering Solutions
DES provides customized bench test and measurement services. After conducting the test, we have the tools and experience to analyze the data and offer solutions to your problems. All of our instruments are maintained and calibrated traceable to NIST standards.
-
Product
Application Performance Testing
-
An important part of application performance testing is to conduct such tests in conditions that realistically reflect the environment in which the application is ultimately expected to operate.
-
Product
Regression Testing
-
Regularly refreshing your website or app attracts new customers and keeps your existing user base engaged. But releasing new functionality and features or fixing known bugs can trigger problems in apparently unconnected areas.
-
Product
Multi-Service Transport Test Solution
MX Series
-
The VeEX MX product series offer a complete test solution for Metro Ethernet network installation and maintenance. Powerful features such as symmetrical and asymmetrical RFC2544 conformance testing, Multiple independent stream generation, Stacked VLAN (Q-in-Q) and MPLS tagging, and Dual Port Traffic Generation/Analysis are available at 10GBase-R, 1000Base-X and 10/100/1000Base-T test interfaces. Fiber Channel testing at 1Gbps and 2Gbps rates is supported on select models.
-
Product
Test Automation System for Heavy-Duty Engine Emission Testing
STARS HDEET
-
STARS HDEET is a Heavy-Duty Engine Emission Test application available as an optional extension to STARS Automation. It provides efficient test cycle execution, emissions equipment control, results calculation and reporting, in compliance with the different legislative standards. Its flexible design offers a wide range of customization while addressing the various requirements for research and development, conformity of production, and certification testing.
-
Product
Package Testing
-
Package testing helps manufacturers verify their package designs to ensure that their products will not experience damage during shipping. Products are often shipped across states, countries and continents to reach their destination. This is an unavoidable link in the supply chain and, as such, packaging must be designed to protect products during the shipping process.
-
Product
Protective Relay Test Kit
PW460
-
PW460 Protective Relay Test Kit is the comprehensive protection relay testing equipment for all types of protective relays with high accuracy. This relay test kit has in-built output monitoring and recording function and supports testing IEC 61850 digital relay.
-
Product
Analog Test Solutions
ATX series
-
The ATX series of instruments are designed for applications that require an analog performance that is not achievable with industry standard platforms like PXI(e).
-
Product
Testing Services
-
The EI Group, Inc. (EI) is an environmental, health and safety consulting firm that offers comprehensive services to a variety of public and private sector clients. Founded in 1988, EI boasts a staff of professionals that have the experience and training required to provide cost-effective, results-oriented consulting services across the United States and abroad. These services are provided with an aggressive, relationship-focused philosophy in order to exceed our clients' expectations regarding quality and timeliness.
-
Product
Testing Kits
Testing Kits
-
Solo testers are available either as separate components or as complete kits – configured both by height and application. The price of complete kits is usually less than the sum of the component parts.
-
Product
Cable Test Van
BAUR Transcable 4000/A 80-3
-
Transcable 4000/A 80-3. The transcable 4000/A 80-3 cable test van is equipped with an automatic control system. The high voltage switch unit is enclosed and is actuated electrically with the fully automatic KE 3 control unit.
-
Product
Mechanical Testing
-
The Mechanical Testing Department at IMR is well equipped to perform most standard mechanical testing, as well as specialized tests designed to the customer's requirements. A complete in-house machine shop supports the department with precise specimen preparation and fixture fabrication.
