Air Data
measures of piloting performance.
See Also: Air Data Test, Altitude, Pitot, Airspeed, Pitot Static
-
Product
Air Data Tester
PS131b
-
Aircraft Development Industries cc
The Model PS131b is identical to the PS131bII except that it is housed in a 19 inch U2 rack mount enclosure. This is suitable for equipment racks in a workshop environment. Like the PS131bII it is an advanced Air Data - Pitot Static Tester, which is a completely digital, microprocessor-controlled device using all solid state transducers and components.
-
Product
Pitot Static Test & RVSM Air Data Accs Kits
ADA320-723
-
Kit Model ADA320-723 (Bar type) contains the equipment required to connect the Air Data Tester to the pitot and static ports, for the performance of a complete test of the main and alternate Air Data System of the Airbus Industries A-319, A-320, A-321 aircraft. The equipment is approved by Airbus Industries.
-
Product
Air Data Test Set System
B511
-
The BRAT Option B511 is an option to the BRAT Test System utilizing Commercial-Off-The-Shelf (COTS) equipment. The system is used to augment the existing BRAT capabilities to test rate of change of altitude or pressure.
-
Product
Air Data Test Sets
-
For calibrating altimeters, airspeed indicators, rate-of-climbindicators and other avionic instruments.
-
Product
Main Air Data Test Fixture for ADC's
TA-245
-
This is the Main Air Data Test Fixture as shown in the AZ-241 repair manuals and will allow by the book testing of the units.
-
Product
Air Data Adapter Test Panel
TA-241
-
AZ-241 Adapter Panel is designed to meet manufacturer's requirements. This panel will allow by the book testing of the air data computer when interfaced with the main air data test fixture. The Scott-T transformer is optional or can be customer supplied. Without the Scott-T your API can read the altimeter resolver directly.
-
Product
Laboratory Air Data Test Sets
-
DMA is a leading manufacturer of Air Data Test Set models for laboratory use achieving the highest accuracy and resolution. The MPS46 is digitally controlled through a keyboard, it uses very high accuracy pressure sensors, with a special characterisation for maximum accuracy (for static channel < 2 feet at sea level). Pressure resolution of 0.2 Pa. is also achievable. The intuitive user interface with touchscreen display ensures that all the functions are controlled with a minimum of key presses . The ADTS can be used in avionics ATE systems (rack height only 2U) for automated pitot-static testing through RS232, USB, Ethernet or GPIB/IEEE488. An internal pump or external rack mounted pump unit can be supplied as an option.
-
Product
Air Data Calibration
-
Fluke calibration offers digital pressure monitors, air data calibrators and laboratory standards for air data pressure range calibrations. Each of these systems feature pressure ranges, measurement units and features specific to calibrate air data test sets and RVSM compliant air data instruments. Models include 2468 Ruska and ADCS-601 DHI primary level standards; 7750i Ruska air data controller/calibrator and RPM4-AD DHI reference pressure monitor.
-
Product
Pressure Instruments Department
-
Aero Instruments & Avionics, Inc.
The Pressure Instruments Department tests, repairs, and overhauls a wide variety of Instrumentation for all narrow and wide body aircraft. Three Martron ATE's are utilized for testing & troubleshooting of Air Data Computers.
-
Product
Air Data Computer (ADC) Tester
MS 1122
-
The ADC tester is used in 2nd line maintenance is to check the functionality of ADC. This unit is a rugged customized hardware based on full functionality test of ADC. The Air Data Computer (ADC) Tester is a fully automated GO/NOGO tester with full functional testing in 2nd line maintenance. This tester is to test ADC at unit level and identify faulty Shop Replaceable Unit (SRU). This tester is also used to carry out PI checks on ADC before clear them for installation on aircraft. ADC Interface board designed to test full functionality of ADC. The Air Data Computer (ADC) test equipment shall be used for testing ADC of Tejas Aircraft. ADC test equipment shall verify the functionality against specifications during second line maintenance and pre-installation on the aircraft.
-
Product
Pitot / Static Tester for Laboratories and Workshops
ADSE 741
-
The ADSE 741 is a complete high performance three channel Ps, Pt and AoA stand-alone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air speed indicators, pneumatic AoA (Angle of Attack) indicators, MACH-meter, air data computers, specific probes and sensors.The high precision embedded sensors enable the ADSE 741 to be used as a pressure standard.The user interface is programmed underWindows and Labview, with a data base managed in a spreadsheet for easy evaluation, management, statistics and presentation.
-
Product
Air Data Tester
PS131bII
-
Aircraft Development Industries cc
The Model PS131bII is an advanced Air Data - Pitot Static Tester, which drastically simplifies the process of testing the aircraft's Pitot and Static system. The test altitudes, airspeeds and vertical speeds are achieved by simply typing in the values and the tester will automatically do the rest. The Model PS131bII is a completely digital, microprocessor-controlled device using all solid state transducers and components.
-
Product
Static Tester for Lab and Workshop
ADSE 715 RS
-
The ADSE 715 is a complete high performance single pressure Ps stand-alone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air data computers ) and sensors. The high precision embedded sensors enable the ADSE 715 to be used as a pressure standard. The user interface running on a PC connected through USB link is programmed underWindows and Labview, with a data base managed in a spreadsheet for easy evaluation, management, statistics and presentation.
-
Product
Pitot Static Indicator
ADSE 740
-
The ADSE 740 is a complete high performance dual pressure Ps and Pt standalone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air speed indicators, MACH-meter, air data computers ...) and sensors.
-
Product
AutoPump Air-Powered Data Module
-
The QED AutoPump Data Module is a water-resistant enclosure that protects and shields surface instrumentation from weather and/or harsh site conditions while providing easy access, via a see-through window, to key system instrumentation readings.
-
Product
Ramp or Flight line Air Data Tet Sets
-
The test sets are all digitally controlled through a local or remote keypad and display. The intuitive user interface allows test set functions to be easily controlled with a minimum of key strokes, with all test parameters displayed, and is suitable for both first time and more advanced users. Optionally many of the ADTS can be remotely controlled by a PDA Pocket PC with wireless Bluetooth connection. The intelligent user interface provides protection to both the test set and the UUT. The software rejects entered command values that exceed the pre-selected limit ranges.
-
Product
Air Temperature Probe
U1183A
-
Measure dryer, transport pipe, and surrounding air temperature within the range of -50°C to 800°C.
-
Product
Intelligent 16 Bit Data Acquisition
CPCI-AD16
-
The CPCI-AD16 module provides a 3U high performance data acquisition subsystem. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digitalfiltering, etc. Application software can be downloaded to the DSP via the CPCI interface. Instrumentation amplifiers provide over-voltage protection, gain and filtering on a per channel basis. Internal scan and trigger clocks are derived from either the CPCI bus clock or the local DSP clock. Dual 32 bit timers can programmed to pace the acquisition process. The CPCI-AD16 can also accept external scan and trigger signals from a front panel connector.
-
Product
4-CH 16-Bit 2MS/s Simultaneous-Sampling USB DAQ Module
USB-1210
-
The USB-1210 is a 16-bit high-speed USB 2.0-based DAQ module equipped with 4 analog input channels providing simultaneous sampling at up to 2MS/s per channel. The USB-1210 delivers high accuracy and excellent dynamic performance at maximum sampling rates, and flexible trigger functions. In addition, onboard 64M samples FIFO ensures no data loss during acquisition even when CPU or system loading is heavy.The USB-1210 is USB bus-powered and equipped with removable screw-down terminals for easy device connectivity. The attached multifunctional stand can be used for desktop, rail, or wall mounting. Suitable for high-speed data acquisition, laboratory and medical research, the USB-1210 provides a reliable measurement solution at an affordable price.
-
Product
16-CH 16-Bit 250 kS/s Low-Cost Multi-Function DAQ PCI Express Cards
DAQe-2213/2214
-
ADLINK DAQe-2213/2214 can sample up to 16 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 8 AI channels in order to achieve maximum noise elimination.
-
Product
48-Ch TTL DI/O IDAQ Module
iDAQ-751
-
Hot-swappable in iDAQ systemDetachable Euro-type spring terminal connectors48-channel TTL digital I/OsConfigurable digital I/O directionIsolation protection of 60 VDCSupports buffered acquisition/update rates up to 200kHz
-
Product
4-CH 24-Bit 128kS/s Dynamic Signal Acquisition USB 2.0 Module
USB-2405
-
The USB-2405 is a 24-bit high-performance dynamic signal acquisition USB module equipped with 4 analog input channels providing simultaneous-sampling at up to 128 kS/s per channel. The USB-2405 also features software selectable AC or DC coupling input configuration and built-in high precision 2 mA excitation current to measure integrated electronic piezoelectric (IEPE) sensors such as accelerometers and microphones.
-
Product
15-CH Isolated Digital Output Module
ND-6056
-
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
16-CH 12/16-Bit 100 kS/s Low-Cost Multi-Function DAQ Cards
PCI-9111 Series
-
ADLINK PCI-9111 series are 16-CH, 100 kS/s low cost multi-function DAQ card. The PCI-9111 series feature flexible configurations on analog inputs. A RC filter is implemented on each A/D input channel for user to attenuate or filter input signal. The PCI-9111 series provide analog inputs with 5 programmable input ranges for bipolar inputs. The PCI-9111 series also support automatic analog input scanning. PCI-9111DG provides 12-bit A/D resolution while PCI-9111HR provides 16-bit A/D resolution. The PCI-9111 series also feature 1-CH 12-bit analog output, 16-CH TTL digital inputs and 16-CH TTL digital outputs. ADLINK PCI-9111 series deliver cost-effective and reliable data acquisition capabilities, and is ideal for a broad variety of applications.
-
Product
8-CH Relay Output Module
ND-6063
-
- 8-CH relay outputs- Output Type: 8 Form A- Contact Rating: AC: 0.5 A / 125 V; DC: 1 A / 30 V or 0.3 A / 110 V; ON/OFF Interval Time: 3 ms- Breakdown Voltage: 500 VAC (50/60 Hz)
-
Product
Data Acquisition System - 3U 5-Slot
DAQ-35CP0G
-
is a preconfigured rugged system ideally suited to support a multitude of military/aerospace data acquisition applications that require "SBC-less" remote Gig-E command and control of high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications; Thermocouple Measurement; Discrete I/O; Differential Transceiver and Dual-Port Gig-E Ethernet.
-
Product
Digital I/O Module
ND-6050
-
- Interface: RS-485- 7 TTL digital inputs- 8 open collector DO- Output up to 30V, 30mA max. load- Programmable input polarity
-
Product
Isolated USB Digital I/O Modules (OEM Version Available)
USB-7230/7250
-
The USB-7230/7250 USB-based digital I/O modules feature high voltage on/off control and monitoring, and isolation voltage supported up to 2500VRMS. The USB-7230 provides 32-CH isolated digital I/O and 2-CH frequency/event counters. The USB-7250 provides 8-CH relay output (4 form C and 4 form A), 8-CH isolated DI, and 2-CH frequency/event counters. The USB-powered USB-7230/7250 features removable screw-down terminals for easy device connectivity, and the included multi-functional stand fully supports desktop, rail, or wall mounting.
-
Product
Data Acquisition System - 3U 1-Slot
DAQ-31CP0G
-
The DAQ-31CP0G is a preconfigured rugged system with a high-performance, low power ARM® Cortex®-A9 processor. It is ideally suited to support a multitude of data acquisition applications that require high-density, multichannel, programmable communications consisting of: ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939) and Dual-Port Gig-E Ethernet.
-
Product
RS-422/RS-485 Repeater
ND-6510
-
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
