-
product
Power Architecture Tools
Cosmic's toolchain for the Power Architecture family is part of a complete and uniform product line incorporating over 20 years of innovative design and development. All Cosmic products include one year of technical support and updates.
-
product
Dynamometer Power Supply
DES Series
The DES 310 and DES 311 power supplies are suited to the entire range of Magtrol's Eddy-Current and Powder Brake Dynamometers. To avoid any disruption of the surrounding electronic modules, the DES 310 / DES 311 supplies are fitted in an industrial housing made of extruded cast aluminum. This housing must be installed directly on the test bench, as near to the dynamometer as possible.
-
product
4-Quadrant Power Amplifier
PAV10000
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
product
Rack Mount Power Supplies
AC-DC Dual Tracking Output Power Supplies
These power supplies are constructed in sturdy extruded aluminum assemblies designed expressly for mounting in standard 19" wide RETMA cabinet racks. The front panels are finished in light gray enamel.
-
product
POWER ATTENUATORS
TYPE ATF
National RF’s Type ATF Power Attenuators were designed to allow interfacing of linear power amplifiers to RF exciters, where a specific amount of drive to the amplifier is prescribed. Often, however, drive from the RF exciter exceeds this minimum prescribed level and some form of power attenuation must be used in order to not damage the input of the power amplifier. National RF’s type ATF-3 offers 3 dB of power attenuation (1/2 of the power) when used between the exciter and the amplifier and will handle an input power of 132 Watts, RMS (continuous power) while providing about 66 Watts RMS output power, when it is terminated into 50 ohms. In practice, the ATF-3 attenuator will handle exciters achieving Peak Envelope Power levels (PEP) in the area of 200 to 250 Watts while providing half of that power to the load. For less attenuation requirements, the ATF-1 and ATF-2 offer 1 and 2 dB of attenuation, respectively.
-
product
POWER PROBE MAESTRO
PPTM01AS
*Connects with the new Power Probe Tek application for greater diagnostic functionality*The Maestro and Power Probe Tek App will be compatible to connect with a majority of diagnostic scan tools*Trace mode offers scope-like functionality*Stream and record visual traces of electrical issues found when diagnosing*DC voltmeter with the capability of applying battery supplied voltage or ground*AC voltmeter: TRMS, peak-to-peak/min/max, frequency, duty cycle*Resistance testing with a live or unloaded circuit*Fuel-injector test mode*Driver test for testing module drivers
-
product
Powerful Diagnostic Instrument
Flex-US
The design of the Flex.US is based on the popular "Flexible Sensor" from SDT. Mounted on the end of a flexible steel pipe, the ultrasound sensor can access any hard-to-reach location. Bend, twist and curve your Flex.US to suit your inspection. Safely scan electrical cabinets and behind machinery guards without putting your hands in danger. To ensure comfort, the volume control is quickly adjusted when very loud ultrasounds are encountered. This sensitivity provides a high level of precision making leak detection a pleasure, not a chore.
-
product
Power Quality Analyzer & Motor Analyzer
438-II
The Fluke 438-II Power Quality and Motor Analyzer adds key mechanical measurement capabilities for electric motors to the advanced power quality analysis functions of the Fluke 435 Series II Power Quality Analyzers.
-
product
Fluid Power Actuators
CP
CP range pneumatic actuators are a versatile, modular, scotch yoke design available in both double-acting and spring-return configurations. The compact and efficient design yields high torques even at low pressures. The design concepts found in Rotork's large, heavy-duty actuators has been applied to the CP range, which brings heavy-duty actuator qualities to small, quarter-turn actuators.
-
product
Ultra-low Power NDIR CO₂ Sensor
CozIR®-LP2
The CozIR®-LP2 is an ultra-low power NDIR CO₂ sensor using state-of-the-art solid-state LED optical technology. The low-power LEDs are manufactured in-house, giving GSS complete control of the CO₂ sensor signal chain.
-
product
Power Module And Device Testing System
Dynamic and static test system Meet the power IPM module dynamic and static electrical parameters test
-
product
Power Supply PowerLab 305d-ii
PowerLab triple Series power supplies are reliable and accurate laboratory equipment with two outputs with adjustable and stabilized DC voltage and regulated (limited) power consumption and additional output has-voltage. Adjustable outputs can work independently, in series (max output voltage 120V DC for model 605-II) or parallel (max current of 10A for models 305-II and 605-II). Power can be used in the design of electronic products, scientific works, laboratories, production lines and in teaching.
-
product
Power Meters and Calibration Cells
The Solar Reference Cell consist of a 20 x 20 mm monocrystalline silicon Photovoltaic Cell encased in a 92 x 70 x 16 mm metal enclosure with a protective quartz window and a temperature sensor. The temperature sensor is a 100 ohm platinum Resistance Temperature Detector (RTD).The Solar Reference Cells come with a Certificate of Calibration and compatible set of connecting cables. The following parameters of the reference cell are certified: Isc, Imax, Voc, Vmax, Pmax, Area, Fill Factor and Efficiency. The certification is accredited by NIST to the ISO-17025 standard and is traceable both to the National Renewable Energy Laboratory (NREL), and to the International System of Units (SI). A compatible cable set is also supplied with each Solar Reference Cell.
-
product
*High Power Laser Beam Dumps & Low Power Beam Traps
Laser beam dumps for high power laser processing, laser measurement and other applications, and low power beam traps
-
product
Digital Power Meter
It is a power meterwith superior performance an powerful functions. In addition, it has simple structure and operation.
-
product
Universal AC-DC Power Supplies
PS-RS25-5
WINSYSTEMS’ PS-RS25-5 is a small, convection cooled 25W power supply for embedded systems. It is a universal design that accepts 88 to 264VAC input and generates up to 5A of current at +5 volts. The +5 volt output can be adjusted with an on board trimpot. The PS-RS25-5 is small, measuring only 79 x 51 x 28mm.
-
product
Chassis-Mount Power Supplies
Advanced Energy’s chassis-mount, DC-to-DC, high voltage modules work easily within OEM equipment as component power supplies. Benefit from full-range control and voltage and current monitoring.
-
product
All Digital Continuous Power Systems
DT Series
The DT Series ET is a digital Uninterruptible Power System (UPS) which features Clary’s On-Line Double Conversion, Power Factor Corrected technology built for extreme temperature. Not only does the DT Series ET offer the highest reliability available on the market today, we consider it On-Line Double Conversion technology at its best.
-
product
Low Power Wireless Gas Detector
CX
Teledyne Gas & Flame Detection
Model CX sensors are equipped with standard analog 4-20mA, and Modbus™ RTU RS-485 outputs and can be used with SmartWireless Site Sentinel CX/CXT controllers. The CX is a very low power device making it an ideal choice for a battery powered detector (optional) in applications where power is unavailable or not economically feasible.CX gas detection sensors are easily and economically deployable in both permanent and temporary installations. These low power sensor assemblies utilize electrochemical technology for a long list of toxic gases.
-
product
Plug-In Power Supplies
VECTOR Electronics and Technology, Inc.
Standard PCI output Voltages : 5.0V, 3.3V, +12.0V, -12.0VHot swap, N+1 redundancy with internal OR-ing diodes.99 power factor corrected AC 90-264V input DC 36-72V (48V nom.), or DC 18-32V (24V nom.) Current sharing on 5.0V and 3.3V outputs Power & Fault LED indicators to faceplate Excellent performance
-
product
Power Supply 600W
UEP10M88 / CEP10M88 -
The UEP10M88 series is a linear regulated plug-in power supply for use in CERN type NIM and CAMAC crates with 600W power output. This high precision and lowest noise power supply is designed as a very compact unit with extremely low volume to power relation.
-
product
Power Sources
EPOS 340 is the multi-functional three-phase generator which comes into its own whenever maximum power and high signal accuracy are required.Intelligent amplifier technology and fully synthetic signal generation make it possible to issue any signal shape across a wide frequency range or even to play back complex transient signal characteristics. EPOS 340 is designed for use as a stand-alone device or for operation with an external PC.
-
product
DC Power Supply
A DC power supply is an instrument that produces a pure, stable DC power supply. There are several important parameters when choosing a DC power supply, including the number of channels, total power, output specifications per channel, resolution, and so on. Each indicator is related to the needs and applications we actually test.
-
product
Power over Ethernet (PoE) DC/DC
An isolated 25W, PC/104-Plus form factor, 802.3af/at compliant, PoE PD power supply. The Class 4 signature supports up to twice the power of 802.3af compliant PD devices. Designed to power a single board computer from DC power extracted from a CAT5 cable sourced by an 802.3af/at compliant PSE device configured as either an endpoint or midspan device.
-
product
Powered Device Analyzer for 802.3at & 802.3bt
The One-Box solution for 802.3 Ethernet Powered Device testing and verification including flexible emulation of PSE behaviors, scalable feature configurations, and plug’n play testing using a Windows PC.
-
product
Distribution Amplifiers
Step up to a leading range of distribution solutions. Take a single input signal and feed it to multiple locations while still maintaining guaranteed signal quality. Choose from our range of solutions for every need and every budget.
-
-
product
Power Meter
P-Series
The N8262A is a compact and slim LXI-compliant P-Series modular power meter. The N8262A helps you to reduce your test system size and enables LAN-based automated power measurements. Owing to LXI test standardization and its interoperability with existing test assets, your system can be up and ready in no time.
-
product
80W Power Supply, 35V, 2.2A or 60V, 1.3A
E3645A
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features. The Keysight 78W, single output E3645A is a stable and reliable power supply for benchtop and basic automated test applications, and enables versatile solutions for tests that require moderate speed and precision with both GPIB and RS232.
-
product
Power Meter
OrienTek Optical Technology Ltd.
Power Meter and the Visual Fault Locator.The Optical Power Meter can measure dBm,dB and uW in the wavelength band of 850,1300 1310 1490 1550 and 1625nm.The Visual Fault Locator uses CW mode and Modulation mode and helps to detect the optical cable of up to 10km. Battery performance 50 hours operation,Dust and shock proof design,Auto Shut off function.
