PXI Serial Interfaces
See Also: Serial Interfaces
-
product
Serial to Parallel Controller
E84 SPC
300mm equipment manufacturers utilize this off-the-shelf E84 communications controller to provide SEMI E84 compliant communications for their products. With its built-in Load and Unload algorithms it is the perfect E84 communications solution for process tools, stockers, load ports, FOUP buffers, smart storage shelves and simulation load ports. The E84 SPC easily integrates with equipment controllers through a standard serial communications connection.
-
product
Opto Serial Module
DS-MPE-SER4OPT
The DS-MPE-SER4OPT offers 4 RS-232/RS-485 opto-isolated serial ports in a PCIe MiniCard form factor. Each port offers 16C550 compatibility and ultra-deep 256-byte TX/RX FIFOs. Maximum data rates are 1Mbps in RS-232 mode and 10Mbps in RS-485 mode. The board is available preconfigured for 4 RS-232 ports, 4 RS-485 ports, or a combination of 2 RS-232 and 2 RS-485 ports. I/O signals are provided on two miniature latching connectors, with 2 ports per connector.
-
product
PCI Express Host Interface SSD/Drive Decode Support
Teledyne LeCroy provides NVM Express, SATA Express and SCSI Express protocol decoding, analysis and test equipment to SSD storage companies worldwide. It works closely with the following organizations providing equipment to its members and conformance programs.
-
product
4-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V
CPCI-7500
*This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asynchronous, full, half duplex*Transfer rate: progr. up to 115.2 kBaud up to 1 MBaud on request*Protocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bits*Parity: even, odd, none, mark or space*Interrupt lines: automatic through BIOS
-
product
Datum Universal Interface
DUI
Datum Electronics specifically designed the Universal Torque Sensor Interface which accepts serial data, displaying the output data and a wide range of additional analogue and digital outputs, s 4-20mA, +/-5Vdc, 0-5Vdc, +/-10Vdc, 0-10Vdc as well as RS232/485 serial data.The Datum Universal Interface (DUI) interfaces with all our rotary, static, reaction, digital torque sensors and torque transducers, as well as shaft power measurement solutions.
-
product
Serial Port Splitter
With COM Port Splitter you can split one real port into several virtual ports, join real ports into one virtual, and redirect the serial traffic from real port to another real or virtual. You can also share one real serial port among several applications so that they will receive the same data from one serial port simultaneously. You can also join several ports under one name and let applications switch among the free ones. COM Port Splitter is very good at splitting any hardware COM port into multiple virtual COM ports, so that each of them behaves exactly like the original port and has the same name. All virtual ports receive any data that is received by the original port at the same time. For example, COM Port Splitter can let a single serial device interact with multiple applications at the same time. Another job COM Port Splitter can do for you is join some real COM ports into one virtual port, which is rather useful when you need some application to handle multiple serial devices simultaneously. All data received by one of the joined COM ports is instantly forwarded to the joining virtual port and to the application, and vice versa. It is also possible to redirect all serial traffic from a hardware COM port to another COM port (hardware or virtual) with COM Port Splitter, meaning that any data sent to the redirected port is immediately received on the port you redirected it to. You may need this in case you are using some software with very strict serial-port settings and instead of figuring out how to modify those settings you can just redirect the data traffic to it. Besides, COM Port Splitter is essential for creating complex bundles of real and virtual serial ports and interconnecting them as you wish, therefore enabling data exchange between those ports.
-
product
Serial Bus Buffers, Extenders, and Accelerators
The Analog Devices family of I2C solutions support hot swappable, 2-wire bidirectional bus buffers to allow I/O card insertion into a live backplane without corruption of the data and clock busses. Additional supported 2-wire buses include SMBus, PMBus, the ATCA intelligent platform management bus (IPMB), and the HDMI DDC bus. I2C/SMBus Accelerators improve bus transitions to allows multiple device connections or a longer, more capacitive interconnect, without compromising slew rates or bus performance. ADI's software-programmable and pin-selectable I2C multiplexers help resolve I2C address limitations, increase fan-in or fan-out, and integrate bus buffers and rise time accelerators for an all-in-one solution. Resistor configurable I2C address translators can be configured with over 100 unique slave addresses to allow multiple slave devices with the same address to coexist on the same bus.
-
product
Interface Unit
CMM Automation
The Aberlink automation interface adds the capability for Aberlink 3D programs to be remotely controlled and monitored using an external system allowing any Aberlink CMM to be integrated with an automated component handling system, whether this be a fully controlled, PLC driven manufacturing system, a robotic loader or just an automatic bar feeder. The package comprises of an optically isolated digital I/O system and a software module that enables the software to be setup to follow a defined operating sequence to allow the automated operation.
-
product
Operator Interfaces
Watlow Electric Manufacturing Company
Watlow offers reliable, affordable, easy-to-use interfaces for machines and systems. The Silver Series EM touchscreen operator interface terminals feature e-mail, USB, data logging, password security and multiple languages. The EZ-ZONE RUI remote user interface fits in tight spots, its EZ-Key reduces repetitive tasks to one touch and the gateway options connect EZ-ZONE products with other automation equipment and software. Paired with Watlow controllers, these interfaces are the perfect solution for process and machine control applications.
-
product
Mini USB (90º) To 90 Series Interface
J90USBJ
Use in ITA SideTripaddle modules VPC 510104136 required
-
product
Interface Converters
Electro Standards Laboratories
Supporting a variety of medias, applications, and entities such as Casino/Lottery VLT Networks, Industrial Process Control, Government Laboratories, etc.
-
product
PC based Serial Data Analyser
FSA32
This PC application is a tool to monitor and display asynchronous serial data. It can also transmit messages and monitor and set control lines. It has comprehensive triggering facilities, and runs on Windows 95 or later.
-
product
Serial EEPROM
STMicroelectronics is the world's #1 supplier of Serial EEPROM thanks to development of leading-edge technology, recognized product robustness and high manufacturing capacity. ST focuses on the availability of the complete portfolio with short lead times, high flexibility in volume and worldwide distribution through selected partners. ST's comprehensive portfolio offers reliable SPI, I2C and Microwire products in SO8N, TSSOP8, DFN2X3, DFN5, WLCSP and bare die packages.
-
product
Dual-Port Serial Interface Cards
PCI-COM2S And PCI-422/485-2
The PCI-COM2S and PCI-422/485-2 are dual-port, asynchronous serial communications cards designed for use in PCI-Bus computers. They are 6.5 inches (165 mm) long and may be installed in any 5V PCI slot in IBM and compatible computers. Each independent port supports RS-422 and RS-485 balanced-mode transmission/reception, and on the PCI-COM2S, RS-232 single-ended transmission/reception as well.
-
product
sbRIO-9860, Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module
787325-01
Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module - The sbRIO-9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI-XNET product line, the sbRIO-9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while performing low-level FPGA control and embedded monitoring in the same CompactRIO Single‐Board Controller. Non-enclosed modules are available for OEM applications.
-
product
PXI Chassis, Controllers, and Interface Modules
Build a PXI test system, by choosing the chassis and controllers that meet your needs. Keysight offers a variety of chassis with different sizes and performance characteristics.
-
product
SparkFun Serial Basic Breakout
CH340C And USB-C
This SparkFun Serial Basic Breakout is an easy-to-use USB-to-Serial adapter based on the CH340C and takes advantage of the handy USB-C connector. With USB-C you can get up to three times the power delivery over the previous USB generation at 1.5A and and also solves the universally frustrating dilemma of plugging a USB cable in correctly, because it’s reversible! The Serial Basic works with 5V and 3.3V systems and possesses the capability to auto install on most operating systems without the need for additional drivers. The Serial Basic uses the CH340C IC to quickly and easily convert serial signals to USB.
-
product
USB Isolated I/O and Serial Communication Module
USB-IIRO4-2SM
The USB-IIRO4-2SM is a USB multifunction device, incorporating a USB 4-port hub internally to provide four optically isolated digital inputs, four electromechanical relay outputs and two ports of RS-232/422/485 serial communication in one small product. The digital portion is ideal for adding easy-to-install isolated input and relay output capabilities to any PC or embedded system with a USB port. This single USB multifunction device is ideal for a variety of applications such as industrial monitoring, control and communication.
-
product
CANdo Interface
NET50003
CANdo is a compact USB to CAN interface, that allows a PC to be connected directly to an embedded CAN bus. In conjunction with the FREE CANdo Application software, CANdo provides a simple, yet powerful means of testing & analysing a CAN network. The FREE CANdo SDK allows CANdo to be easily integrated into any Windows based program.
-
product
Interface And Connectivity Solutions
From supporting sophisticated connectivity protocols to offering simpler interface options, our comprehensive solutions enable you to develop robust and highly reliable embedded systems.
-
product
High Performance PXI Functional Test System with Mac Panel Interface
TS-5400
The Keysight TS-5400 PXI Series Functional Test System provides automotive, aerospace and defense and industrial control manufacturers with an off-the-shelf PXI hardware and software platform with support for single or multiple DUT test. Designed for testing electronics control modules such as, power train control, complex body electronics and industrial controllers, the TS-5400 PXI Series helps manufacturers achieve higher throughput for their design validation and manufacturing functional test needs with the capacity to empower them to anticipate future functional test needs.
-
product
Multiprotocol Serial Boards
104-COM-8SM-T
This is an eight-, four-, or two-port, asynchronous, serial communication board designed for use on the PC/104 bus. It supports RS-232, RS-422 or RS-485 communications. The board may be installed in any standard PC/104 stack. Connections are made via two 40 pin IDC type right angle connectors. Common applications include POS, gaming systems, machine monitoring, military and high-density networking.Type 16780 UARTS are used as the asynchronous communication elements.
-
product
PCI Mezzanine Card
PNIC1G
Each Ethernet interface supports 10, 100 and 1000 Mbits transmission rates with auto-negotiation for full duplex operation; 10 and 100 Mbit/s transmissions for half duplex operation, and is equipped with a 32 Kbit Serial EEPROM.
-
product
4- or 8-Port Serial Module
Emerald-MM-8EL
The Emerald-MM-8EL-XT is a family of high performance PCIe/104 "OneBank" serial I/O modules offering 4 or 8 multiprotocol serial ports with software-controlled configuration and optional opto-isolation.
-
product
GPIB to Parallel Printer Interface
Model 4892B
* Adds a GPIB Interface to Printers with Centronics or IEEE-1284 parallel interfaces. See the compatible printer list. * Replaces obsolete printers and plotters with a current HPGL/PCL5 printer.* Prints and Plots from most Analyzers. * Large 256 kbyte buffer and high speed GPIB interface off-loads the instrument and reduces printing time.* No program changes required.* Rack mountable in 1 U high rack mount kit.* Includes universal VAC Power Adapter and printer cable.
-
product
Desalter Interface Level Transmitter
This reliable level transmitter is specially designed to maximize the throughput of oil/water separators and accurately measures the electrical interface in the emulsion even in upset conditions. This measurement is critical because the separation vessel operates at maximum efficiency when the electrostatic grid is close as possible to the interface.
-
product
Real-time Hardware Interfacing Package
VISUALCONNX
VISUALCONNX is a visualisation and control software product, allowing real-time hardware or software interfacing, monitoring and logging.
-
product
Serial Digital Interface
Model 2363
* Provides 48 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes or data strings.* RS-232 and RS-485 Serial IO.* 1 U high rack mount kit mounts one or two 2363s* Includes US 115 VAC Power Adapter
-
product
Network Interface for Compact PCIe
cPCIe-ASM-NIC
Avionics Interface Technologies
Quad port FC-AE-ASM Network Interface Controller for Compact PCI Express
-
product
PMC Compatible Bi-Directional Serial Data Interface
PMC-BiSerial II
The PMC BiSerial has been updated to be even better. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-II. The BiSerial II features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
