Thermal Conductivity
See Also: Conductivity Meters
-
Product
CS/ONH-Analysis
G4 PHOENIX DH
-
The highly sensitive thermal conductivity detector allows analysis down to a sub-ppm range, while the optional mass spectrometer allows detection limits in the low ng/g range.
-
Product
H2 and Binary Gas Analyzers
-
PST offer a range of hydrogen (H2) and binary gas analyzers utilising the thermal conductivity property of gases to determine the concentration of a Target Gas (hydrogen for example) within a known Background Gas such as oxygen, nitrogen or argon.
-
Product
Thermitest
THW-L2
-
Designed with speed and operational simplicity in mind, the Transient Hot Wire (THW-L2) Liquid Thermal Conductivity Meter is an advanced measurement system for direct determination of the thermal conductivity of liquids and pastes in accordance with ASTM D7896-19. In less than 2 seconds, a single measurement of small volumes of liquids and pastes can be accurately and precisely measured for thermal conductivity. Using a non-stationary measurement approach, the THW-L2 uses rapid test times to limit convective effects for samples with a wide range of viscosities. The THW sensor consists of a 60 mm heating wire that is fully inserted into an isothermal sample. A constant current source (q) is used to heat the sensor wire and the temperature rise is recorded by monitoring the change in electrical resistance of the wire. The slope (m) is determined from the plot of temperature rise vs. logarithm of time and is used in the calculation of thermal conductivity (λ). Liquid samples of high thermal conductivity will have a lower slope, while liquid samples with low thermal conductivity will have a higher slope.
-
Product
Oxygen/Nitrogen/Hydrogen by Inert Gas Fusion Infrared and Thermal Conductivity Detection
836 Series
-
The ONH836 Oxygen/Nitrogen/Hydrogen Elemental Analyzer is designed for wide-range measurement of oxygen, nitrogen, and hydrogen content of inorganic materials, ferrous and nonferrous alloys, and refractory materials using the inert gas fusion technique.
-
Product
Scanning Thermal Microscopy Module
VertiSense™
-
SThM module for thermal conductivity contrast and a temperature contrast imaging. Supports Contact, Tapping™ and Peak Force Tapping modes. Plug-in module, compatible with most commercial AFMs. Real temperature measurements up to 700° C. Ultra-low noise, high speed amplifier. Innovative probe design.
-
Product
TIM (Thermal Interface Material) Measurement System
-
Thermal Engineering Associates, Inc.
A system for the measurement of thermal conductivity of a wide range of thermal interface materials - grease, pads, foils, etc. - with a measurement range of of roughly 0.1 to 500W/m-K. (>500W/m-K available on custom basis.)
-
Product
Conductivity Type Tester
HS-HCTT
-
It is strictly designed according to the requirements of the hot-probe thermal EMF conductivity type test in standard ASTM F42: Standard Test Methods for Conductivity Type of Extrinsic Semiconductor Materials. A temperature controlling heating element is installed inside the hot probe so that the hot probe is heated automatically and its temperature is maintained in the range 40-60℃.
-
Product
TIM Tester
-
The Analysis Tech TIM Tester 1300 is an automated test system for measurement of thermal impedance and conductivity on thin, thermally conductive materials of the type frequently used for electronic packaging, as well as a wide variety of flexible or rigid solids and semi-liquid or viscous materials. Generally, the TIM Tester 1300 can accommodate samples with high-to-medium thermal conductivity with contact pressures ranging from 10 to 550 psi (70-3800 kpa) and at sample temperature ranging from 15C to 70C.
-
Product
Gas Analyzers
-
Teledyne Analytical Instruments
Gas Analyzers by Teledyne Analytical instruments - carbon dioxide systems, gas chromatographs, hydrocarbon analyzers, infrared analyzers, moisture analyzers, nitrogen analyzers, nitrogen oxides & ammonia analyzers, oxygen analyzers, sulfur analyzers, thermal conductivity analyzers, tunable diode laser (TDL) analyzers, ultraviolet analyzers, and more
-
Product
Cyrogenic Solutions
-
Our leading edge dewar technology combines the highest quality, reliability and expertise in thermally conductive materials. Our unique designs allow you flexibility to use standard dewars for more than one specific application or test.Minimize cryogenic consumption and maximize thermal conductivity.Vibration isolation to enable the most vibration sensitive applicationsTime-tested ergonomic designs for ease of operation
-
Product
40-CH 100G Thermal AWG
-
Flyin’s 40 channel 100G Thermal AWG(100G TAWG) is designed for use within the C -band release of DWDM system. To decrease the power dissipation of the devices in different environmental conditions, the TAWG package is special designed with selection of reliable thermal plastic with low thermal conduction, and the TAWG operating temperature is controlled by using foil resist heater or Peltier TEC with thermistor temperature sensor. Different input and output fibers, such as SM fibers, MM fibers and PM fiber can be selected to meet different applications. We can also offer different product packages, including special metal box and 19” 1U rackmount.
-
Product
Oxygen / Hydrogen Analyzer
ELEMENTRAC OH‑p 2
-
The new ELEMENTRAC OH-p 2 is a powerful and robust elemental analyzer for measurement of oxygen and hydrogen concentrations in inorganic samples like steel, iron, copper or ceramics. The highly sensitive NDIR and thermal conductivity detectors reliably detect element concentrations from low ppm content to high percentages.
-
Product
Non-steady-state probe for thermal conductivity measurement
TP02
-
Hukseflux Thermal Sensors B.V.
TP02 is a probe that offers the possibility to perform a practical and fast measurement of the thermal conductivity (or thermal resistivity) of the medium in which it is inserted at the highest accuracy level. It works in compliance with the ASTM D 5334-00, D 5930-97 and IEEE 442-1981 standards. The standard TP02 probe has proven suitability in soils, thermal backfill materials, sediments, foodstuff, powders, sludges, paints, glues and various other materials. The Non-Steady-State Probe (NSSP) measurement method (also known as transient line source, thermal needle, hot needle, heat pulse- and hot wire technique) has the fundamental advantages that it is fast and absolute while the sample size is not critical. Hukseflux is specialised in NSSP design. Special models have been developed for in-situ field experiments. For permanent installation in soils, a dedicated model, TP01, is available. TP02 has been designed and tested in collaboration with the Applied Physics Group of Wageningen University.
-
Product
Oxygen/Nitrogen by Inert Gas Fusion Infrared and Thermal Conductivity Detection
736 Series
-
The ON736 Oxygen/Nitrogen Elemental Analyzer is designed for wide-range measurement of oxygen and nitrogen content of inorganic materials, ferrous and nonferrous alloys, and refractory materials using the inert gas fusion technique.
-
Product
Thermal needle system thermal resistivity / conductivity measurement
MTN01
-
Hukseflux Thermal Sensors B.V.
The MTN01 Multi-purpose Thermal Needle System allows performing fast measurements of the thermal resistivity or conductivity of soils. It is specifically designed to be reasonably robust, as well as accurate. It is therefore suitable for laboratory as well as field- measurements of soil thermal properties. The sensor is a Non-Steady-State Probe (NSSP), TP07, which is mounted on the Insertion Tool, IT02. The system is operated using a hand-held Control and Readout Unit CRU01.
-
Product
Light/Laser Flash Analyzers
-
Light or laser flash is a measurement technique used to determine the thermal diffusivity, thermal conductivity, and specific heat capacity of materials. Light flash measurements are essential for characterizing the heat transfer and storage properties of a variety of materials, whether the sample of interest is expected to insulate, conduct, or simply withstand temperature changes.
-
Product
CS/ONH-Analysis
G6 LEONARDO
-
The high-end thermal conductivity detector used for hydrogen and nitrogen analysis allows detection limits in a sub-ppm range (based on 1g sample mass)
-
Product
Temperature Sensors
-
Temperature sensors have a well-defined relationship between electrical resistance and temperature, allowing them to measure temperature precisely. The sensor body is made of a thermally conductive material and is as small as possible to produce a rugged device which gives an accurate measurement of temperature with a fast response.
-
Product
1 kW and 2 kW Laser-Based Floating Zone Furnace
Laser Furnace
-
The 1 kW and 2 kW laser furnace for single crystal fabrication is based on a design and developed in close cooperation with the RIKEN Center for Emergent Matter Science under the leadership of Yoshio Kaneko. Both melting zones have 5 lasers each, which guarantees a high uniformity of power density in the melting zone range. The laser profile has been optimized to reduce thermal stress during the crystal growth process. In addition, the system includes an integrated temperature sensor for real-time temperature monitoring. Temperatures up to 3000 °C can be reached and therefore materials with a very high vapor pressure, a narrow temperature range of the melt, a high thermal conductivity coefficient and incongruent melts can be melted.
-
Product
Portable Thermal Conductivity Meter
TLS-100
-
The TLS-100 is a portable thermal conductivity meter used to measure thermal conductivity and thermal resistivity at the push of a button. Each TLS-100 comes equipped with a 100 mm sensor for testing soil, polymers, and other soft materials. An optional 50 mm sensor was designed for testing harder materials, like rock and concrete. The collected data is automatically analyzed, and results are displayed instantly.
-
Product
Gas Analyser
LT GasAnalyzer
-
Highly performant analyzer for measuring the concentration of technical gases based on a thermal conductivity sensor, an infrared sensor a para magnetic sensor or combinations of these sensors. Sensors are precise, robust and have a low cross-sensitivity. Extractive online measurement of the concentration of flammable or non-flammable gas components in gas mixtures. Can measure trace oxygen (O2) levels in the parts per million (ppm) range.
-
Product
Thermal Transport
-
The thermal transport probe measures thermal conductivity and thermoelectric power (defined by the Seeback Coefficient). Electrical and thermal contacts are made to opposite ends of the sample allowing for customisation to suit the sample requirements of the user.
-
Product
Heat Flux Sensors
MF Series
-
EKO Heat Flow Sensors are applied to measure the heat flow or thermal conductivity in materials and radiative IR flux emitted by body surfaces. The sensors are suitable for indoors applications, some models made for outdoors purposes and are available in different sizes and thickness. All sensors are extremely flat, which is a big advantage considering the minimum interference with the conditions of the testing area the thermal dynamics. Since sensor foils are relatively flexible those can easy be applied on curved surfaces and can be used in different applications to measure the performance of insulating materials in refrigerators, container walls, pipes, building constructions, etc.
-
Product
Oxygen/Nitrogen/Hydrogen Analyzer
EMGA-930
-
This is a simultaneous oxygen, nitrogen & hydrogen elemental analyzer with high accuracy and repeatability suiting to cutting-edge technology's R&D as well as quality control in the market of steel, new materials, catalyst and so on. This is a new generation model optimized to fit to user's requests.The oxygen is measured as carbon monoxide and carbon dioxide by two non-dispersive infrared detectors, the nitrogen by a thermal conductivity detector and the hydrogen with non dispersive Infra Red detector as H2O.
-
Product
PXIe-4353, 32-Channel, 24-Bit PXI Temperature Input Module
781348-01
Analog Input Module
32-Channel, 24-Bit PXI Temperature Input Module—The PXIe‑4353 is a thermocouple input module that provides integrated data acquisition and signal conditioning for temperature measurements. The PXIe‑4353 includes increased accuracy and synchronization features for scalable measurement systems from low‑ to high‑channel counts. The high accuracy is attributed to the NI TB‑4353 isothermal terminal block that optimizes thermal conductivity between the thermocouple terminals and the cold-junction compensation (CJC) channels. The PXIe‑4353 has two auto zero channels for offset compensation as well as open thermocouple detection to identify disconnected thermocouples.
-
Product
Guarded Heat Flow Meter
-
The Guarded Heat Flow Meter (GHFM-02) follows ASTM E1530-19 for testing thermal resistance and thermal conductivity of solids, such as metals, polymers and composites. The easy to operate GHFM-02 follows the trusted steady-state approach, with the addition of a guard to limit the effects of lateral heat loss. This design, allows testing of a wide range of materials with low to medium thermal conductivity.
-
Product
Probes Conductivity
-
In-line sensors that measure a solution's ability to conduct electricity.
-
Product
Conductivity Meters
-
GAOTek conductivity meters report the conductivity of a substance as an inverse function of resistivity. Resistivity is measured in ohms/cm, while conductivity is measured in mhos/cm. Our portable conductivity meters and testers are ideal for water conditioning, medical, beverage, laboratory, and other industrial applications. Our high-performance conductivity meters are reliable, high quality, accurate and affordable equipment that facilitate easy inspection and testing. They are compact, portable instruments that allow a user to conveniently work in complex conditions in a lab or onsite.
-
Product
Oxygen / Nitrogen / Hydrogen Analyzer
ELEMENTRAC ONH‑p 2
-
The new ELEMENTRAC ONH-p 2 is a powerful and robust elemental analyzer for measurement of oxygen, nitrogen and hydrogen concentrations in inorganic materials like steel, iron, copper or ceramics. The highly sensitive NDIR and thermal conductivity detectors reliably detect element concentrations from low ppm content to high percentages.
-
Product
Thermal Analysis
-
The TORC (Thermo-optical Oscillating Refraction Characterization) technique applies decades of know-how in optical instrumentation to thermal analysis in a novel and unique way. The technique requires minimal sample preparation at maximal tolerance for sample properties. You can determine the coefficient of thermal expansion, glass and phase transitions as well as polymerization for various samples: liquids, gels, pastes, and certain solids. For example: cured and uncured resins, adhesives, glues, etc. can easily be characterized. Both thermal and time-dependent processes can be monitored with minimal effort.
