PD Test
partial discharge testing.
See Also: Partial Discharge, Partial Discharge Detection, Partial Discharge Monitors, PD, Partial Discharge Test
-
Product
USB PD Test System
6050
-
Single Output USB PD USB PD basic version：the single-group test systemarchitecture is as shown in the table, 5302A AC Source, 3302F + 3310F series and9922-R Quick Charge Controller.
-
Product
Partial Discharge Calibrator
TPK-H
-
The high voltage-resistant Partial Discharge calibrator is used to determine the correction factor in the PD test circui.
-
Product
PD Free Test Transformer
-
Wuhan Fanke Transformer Manufacture Co., LTD
PD Free Test Transformer
-
Product
Inductive Sensor
HFCT Ø 30-39-50mm
-
Techimp HFCT is an inductive sensor for partial discharge measurements. It is suitable for on/off line PD tests on many electrical systems (cables, transformers, rotating machine, etc..). It has to be applied to the ground connection of the system to be tested.
-
Product
Powered Device Analyzer for 802.3at
PDA-602B
-
Emulate all Type-1 and Type-2 PSE’s, powering 2-pairs up to 41W at all PD input voltages. Optionally supports 802.3at PD Conformance Test Suite and LLDP emulations.
-
Product
PD Test Systems
-
1. Number of channels: 2/4 electric signal interfaces & 1 EXT interface 2. Sampling frequency: maximum 200MGa/s 3. Sampling precision: 12bit 4. Range: 0.1mV~20V 5. Range switch: 1mV, 2mV, 5mV, 10mV, 20mV, 50mV, 100mV, 200mV, 500mV, 1V, 2V, 5V 6. Frequency band range: 1Hz-60MHz 7. Range non-linear error: 5% 8. Range of capacitance for test object: 6pF~250µF 9. Power source mode: internal lithium cell / AC 220V 10. Display: 6.5 inches TFT LCD 11. Resolution: 640×480 12. PV: 4GB 13. Hard disk: 32G stiff disk used for storing the test data
-
Product
Superior Handheld Partial Discharge Detector
PDStar
-
Power Monitoring and Diagnostic Technology Ltd.
PMDT is proud to present one of our latest innovations, the PDStar. It integrates On-Line Partial Discharge (OLPD) testing and Infrared testing for MV and HV equipment, which combines UHF, AE, Ultrasonic, HFCT, TEV, and Infrared testing technologies. It is applicable for online PD testing, as well as abnormal heating and defect detection on all types of substation equipment. PD amplitude, PRPD, PRPS, and infrared spectrums provide critical data for determining the operational condition of electric power equipment. It connects to the PMDTCloud via Wi-Fi/3G/4G to upload test data, download test tasks, and receive diagnostic results in real time. Another uniquely advanced feature of the PDStar is that it integrates with a 100 MSPS (Mega-Samples per Second) HFCT signal processor, which greatly improves the performance for power cable OLPD testing.
-
Product
High Frequency Current Transformer
HFCT Ø 140mm
-
Techimp Clamp High Frequency Current Transformer model 140 is an inductive sensor for partial discharge measurements. It is suitable for online /off line PD tests on : large diameter cables ; grounding rod bar ; etc. A TNC termination is available to connect the Clamp HFCT 140 to the TechImp PD analyzer : PDCheck , PDBase etc. The arrow indicates the requested input current (Iin) direction to get coherent output voltage (Vout) polarity respect to ground. When the sensor is installed with the arrow directed to ground, the detected voltage signal (Vout) has the same phase of the input current (Iin).
-
Product
Cable Partial Discharge (PD) Spot Testing And Locating
PrecisePD
-
PrecisePD is an on-line PD Spot Testing and PD location system for Cables and Switchgear with advanced signal processing, used for the detection of PD in high noise environments.
-
Product
PoE PD Test Solutions
-
Explore PoE PD Test solutions from Sifos Technology. What type of testing does your Power-Over-Ethernet Powered Device need?
-
Product
PD Measuring System
TEM
-
Partial discharge test system for laboratory or on-site measurement according to VDE 0434, IEC 60270 and EN50178 consisting of:*Partial discharge meter TMG*High-voltage coupling capacitors for decoupling of the PD pulses*Partial discharge calibrator TPK for determining the correction factor in the PD test circuit
-
Product
AC Hipots for Factory and Field Testing
HPA Series
-
HPA Series test sets perform AC withstand and PD testing (most models) on higher capacitance loads, offering up to 40 kVA and 300 kV AC
-
Product
ITSM Synchro
-
The Impulsive Test Synchronization Module (ITSM) is a device aimed at generating a digital synchronization signal, to use the PDBaseII system for impulsive voltage PD test. The digital synchronization signal generated by the ITSM, is synchronized with the voltage impulse of the impulsive source (voltage generator). The ITSM must be connected between the DIN channel of PDBaseII and the output of the synchronization sensor (e.g. capacitive coupler). The ITSM provides also a low voltage signal reproducing the impulsive voltage source.
-
Product
PD Conformance Test Suite for 802.3at & 802.3bt
-
Sifos Technologies offers the ultimate simplicity in testing a PD’s conformance to IEEE 802.3 Standards with Pass/ Fail reporting in the PD Conformance Test Suite available for purchase with the PDA-600 Family of Instruments.
-
Product
USB Power Delivery and Type-C™ Tester & Analyzer
GRL-USB-PD-C2 (GRL-C2)
-
GRL-USB-PD-C2 (GRL-C2) is the only solution available that supports all compliance test specifications for USB Power Delivery 3.0 and USB Type-C Alternate Mode designs, and enables product developers to quickly run full compliance and validation test suites at the push of a button. GRL-C2 provides an automated, efficient, and fully-integrated way perform all required USB Power Delivery version 3.0 and 2.0 and related tests over the USB Type-C connector, as well as PHY test automation for USB Type-C Alternate Modes. GRL-C2 automates all required USB PD compliance tests for power providers (chargers), consumers, dual-role ports, and cable and adapter E-Markers; and is the only solution available that integrates Qualcomm Quick Charge 4+ and Intel Thunderbolt-specific test items. GRL-C2 also incorporates analyzer capability to sniff PD traffic. GRL-C2 integrates all required USB PD tests into a single 2-port tester, including all tests supported on GRL’s USB-IF approved first generation solution introduced in 2015. Each port can be configured independently as a PD Provider or Consumer. All other PD Protocol and Power tests are fully integrated, removing the need for external electronic loads.
-
Product
Online PD Spot Tester
Liona
-
Cable testing and diagnostics with the BAUR liona. Liona is a portable online PD spot tester for measuring and locating partial discharges in cables and switchgear during normal mains operation. Liona lets you test cable systems and electrical equipment online without switching off partial discharge activities, and then generate trend analyses. Even a PD spot test (duration: 5-10 minutes) is capable of reliably assessing the current status of your system.* Automatic PD detection during normal mains operation (without switching off the cable route)* With DeCIFer technology: PD identification based on 500 million measurement results* Precise online PD mapping with PD transponder
-
Product
Capacitive Divider
-
It can be chosen as PD sensor for Techimp PDCheck, PDScope or PDBaseII systems. It is suitable for on line or off line PD tests onrotating machines, for both spot measurements and monitoring applications. A BNC termination is available to connect the coupler through a coaxial cable.
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131E
test
Achieve phase stability with this 96.5-cm cable when a DUT is connected, with adapter, directly to the test set port
-
Product
Test Management Software
ActivATE™
test
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
Product
Interactive Benchtop Test
test
Strict time-to-market deadlines make it vital to efficiently debug and validate product designs. Virtual instrumentation provides a unified interface that gives engineers an advantage over traditional box instruments.
-
Product
NI Real-Time Test Cell Reference System
778820-35
test
DIAdem Advanced with DAC Bundle, Perpetual License, Include 1 Year SSP
-
Product
Wireless Test Standards Software
test
Generate and analyze signals for cellular and connectivity standards with NI PXI RF instrumentationPerform advanced automated test with the easy-to-use NI-RFmx software APISave on all NI RF wireless test software under a single license
-
Product
Semiconductors Testing
test
Our Testers support the production lines of variety of products such as 40/100 GBps Mux/DeMux, LNA, WiMAX RF Transceivers, Microwave & Millimeter Wave components. This high reliability products are being used in (a) Networking & Communications (b) Consumer Electronics (c) Military & Space
-
Product
Advanced SoC Test System
3680
Test System
The Chroma 3680 is an advanced SoC test system with data rate up to 1Gbps. The Chroma 3680 is capable of conducting parallel tests on multiple chips to meet the digital and analog IC testing requirements, with applications including MCU, digital audio, digital TV, set-top box, DSP, network processor, field programmable gate array (FPGA) and consumer electronics.
-
Product
Explosive Test Site Range Instrumentation
test
Firesets, CDU’s EDU’s, Delay generators, firing panels, and custom instruments. Fiber-optic and computer-control options.
-
Product
CPE Design Verification System
Jupiter 310
Test System
Jupiter is the industry standard for automated DOCSIS physical (PHY) layer testing. It provides the most comprehensive test coverage and accurate results on the market for DOCSIS 3.1 devices.
-
Product
Mixed Signal, Multi-Functional Test Module
PXIe-ScanIO-112
Test Module
The PXIe-ScanIO-112 delivers a powerful combination of digital, analog, and AC-coupled testing in a single PXIe module. With 104 boundary-scan controllable digital I/O channels and 8 analog I/O channels ranging from –15V to +15V, engineers gain the flexibility to test a wide variety of board-level designs. The module supports IEEE-1149.6 AC-coupled interconnect testing, configurable single-ended and differential pin operation, and integrates seamlessly with the Corelis ScanExpress™ suite.
-
Product
Design for Testability (DFT Test)
test
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
Product
Configurable Functional Test System
ATS-5000
Test System
Maximize the uptime of your most critical electronics with the ATS-5000 Functional Test System from Astronics Test Systems. Deployed globally for more than 20 years, the newest version of this tester provides a configurable, affordable solution that delivers just enough test.
-
Product
Automated Compliance and Device Characterization Tests
N5990A
Test Platform
The Keysight N5990A test automation software platform is the most powerful tool for serial and multi-lane gigabit testing. It is the unique universal platform for testing a wide range of digital buses such as PCI Express, USB, HDMI or MIPI. The same graphical user interface and operating principles are used for all applications. This boosts productivity, especially when testing devices which support multiple digital buses. The N5990A can be tailored to your individual test needs with the flexible test sequenzer and controls all instruments needed for your tests. The configurable database interface of the N5990A test automation platform enables the convenient storage of all test results. A web interface allows an effective and easy operation. Custom calibration and test procedures can be implemented easily with User Programming.
