-
Product
In Line Load Cell (10KN-50KN)
106, 107, 108 Series
-
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 50kN and 10klb with better than ±0.5% non-linearity. This type is also available with fully welded cover.
-
Product
34-Pin IDC Connector, 1A, Straight PCB Mount, Male
40-963-534-SM
-
This accessory is designed to be used for terminating a 34-Pin (0.050" pitch) Ribbon Cable Connector to a PCB and includes a strain relief latches.
-
Product
48-Channel High Performance Strain Gauge Measurement Instrument
EX1629
-
48-Channel High Performance Strain Gauge Measurement InstrumentSupports quarter-bridge (120, 350Ω or user defined), half-bridge or full-bridge24-bit ADCs, sampling rates up to 25 kSa/sBuilt in programmable differential excitation -8V to 8VBuilt in selectable bridge completionConfigure signal conditioning excitation and bridge completion on a per channel basisSimple, low-cost wiring using RJ-45 telecom connectorsSupports TEDS for easy transducer detection and setupRJ-45 input connector reduces setup cost and timeBuilt in self-calibration and shunt calibrationSupports voltage, ratiometric and linear measurements other than strain measurements.
-
Product
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle
865684-01
-
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9215, cDAQ-9171, and NI-9981 includes the NI-9215 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the NI-9981 Connector for strain relief and operator protection from high-voltage signals. The included NI-9215 provides noise immunity, a high common-mode voltage range, NIST-traceable calibration, differential analog inputs, and four channels.
-
Product
Digital Image Correlation System for Complete 3D Warpage, Thermal Expansion, and Strain Analysis of Materials and Components in the Heating and Cooling Phase
Q-400 TCT
-
The Q-400 TCT system is designed for complete three-dimensional and highly sensitive warpage, thermal expansion measurement and strain analysis of materials and components in the heating and cooling phase. Areas from 50 mm x 70 mm down to 2 mm x 3 mm can be investigated. Measurements can be done from room temperature up to 300°C and down to -40°C. The system is specially suited for thermal expansion measurement of electronic components and is frequently used in the development and testing of complex anisotropic materials, components, and structures in electronic applications.
-
Product
34-Pin IDC Breakout, DIN Rail Mount, Screw Terminal
40-967-534-M
-
This accessory is designed to be used for terminating a 34-Pin (0.050" pitch) Ribbon Cable Connector and includes a strain relief. The accessory is suitable for mounting on DIN rails.
-
Product
20-Pin GMCT Female Connector, 10A, Without Backshell
92-960-020-10A-F
-
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 16 AWG. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
Torque Instrument
-
DTR is a microprocessor based digital indicator, totally autonomousand with input for strain gauge based torque transducers.A ≤±0,02% accuracy makes it possible to be used use in qualitysystems as first or second line sample, periodically calibrated by aSIT center. Measuring system consists of a particularly long-termstable analogue section, of a carrier frequency amplifier whichminimises thermal drifts and of a 16 bits A/D converter whichensures 65.000 internal divisions.
-
Product
Strain Gauge Module
МТМ8
-
Mezzanine module (mezzanine) МТМ8 is designed to measure the output signal of strain gauges. The mezzanine can be used with any bridge sensors (pressure, force, etc.).
-
Product
High Temperature XY Planar Biaxial Extensometer 1200 C or 1600 C)
Model 7651
-
Jinan Testing Equipment IE Corporation
Model 7651 extensometers measure combined in-plane strains in flat cruciform specimens tested in machines capable of simultaneous X and Y (perpendicular) axial loading and on standard flat samples tested in pure tension. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7651 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to eliminate crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃(2900°F) high temperature option.
-
Product
PCI Simulation Modules For Sensor Simulation
-
Does your test strategy require simulating environmental sensors, including temperature, pressure, altitude, and strain gauges.
-
Product
20-Pin GMCT Cable, Female to Unterminated, Cut Ends, 10A, 3m
A020GFR-C-0C300
-
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
Sheet Metal r-Value Extensometers
Model 3575AVG
-
Jinan Testing Equipment IE Corporation
Designed for measuring r-values in sheet metal testing, this extensometer averages the lateral strain at two locations. This model may be used simultaneously with the Model 3542 axial extensometer.
-
Product
sbRIO-9236, Non-Enclosed, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
781580-01
-
Non-Enclosed, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The sbRIO‑9236 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The sbRIO‑9236 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. Non-enclosed modules are designed for OEM applications.
-
Product
4-Pin Power D-Type Female Connector, 40A, Without Backshell
92-960-004-F
-
This connector is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
Product
Force Sensors And Strain Sensors
-
Force and strain measurement in machines, installations, and tools.
-
Product
Radio Telemetry
-
Procter & Chester Measurements Ltd
Radio Telemetry: A transmission of data from a remote source via a radio to a receiving station for recording and analysis.Inductance: A contactless method of supplying power to (in this case) a strain gauge bridge. The signal is then transmitted back to the electronics.Slip Ring: Consists of a conductive band mounted on a shaft and is insulated from it. The wheatstone bridge is connected to the bands (usually four off). Fixed brushes or contacts make contact on to the bands to transfer power to the bridge and signal back to the static instrumentation.
-
Product
4-Pin Power D-Type Male Connector, 40A Without Backshell
92-960-004-M
-
This connector is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
Product
Deflection Gages (Deflectometers)
Model 3540
-
Widely used for measuring deformations in three and four point bend tests, compression tests and a variety of general purpose deformations. These strain gaged devices come with a magnetic base for easy mounting.
-
Product
Segmented STEM Detector
Opal
-
In a drive to meet our customers’ needs, El-Mul developed a detection solution for Scanning Transmission Electron Microscopes (STEM) which can support multiple applications such as DPC, cryo tomography, imaging of strain, charge, light elements or Z-contrast.
-
Product
Circuit Tester "Light and Sound" Hook Probe
TE6-0708C
-
Hangzhou Tonny Electric & Tools Co., Ltd.
*Tests 6/12 volt circuits with POWER ON.*Interchangeable tips allow tool to be used as a probe- or pierce-type tester.*Retains wire for perfect pierce with one hand.*Hook grabs hard-to-reach wires.*Durable insulated clip and heavy-duty cord for professional use.*Spring loaded strain relief prevents cord pull out and damage.*High intensity glow for under hood and under dash visibility.*Easy-to-hear buzzer provides quick circuit test confirmation.
-
Product
Load Cell Amplifiers
-
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
Product
Analog to Digital Converter
7418/7419
-
Supports thermocouples, RTD's, strain gauges, voltage in, 4-20 mA, thermistors, and resistorsUp to 16 differential input channels plus sensor excitationEach channel is software programmable for sensor type, gain, low-pass filtering, scan rateAuto-calibration eliminates trimpotsLow power consumption
-
Product
Torque Verification
90229
-
SDI’s 90229 is designed for calibrating tools used to apply torque including electric and pneumatic power tools, torque sensors, hand and click wrenches. The strain gage based reaction torque sensors in the bench-mount housing remain stationary while torque is applied. The housing dis-assembles by removing two snap pins, allowing the user to easily change socket sizes and capacities.
-
Product
PXI Strain Gauge Simulator Module 2-Channel, 1.5K
40-265-402
-
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 1.5Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Load Cells
-
The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 2k
50-265-302
-
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Cut Ends, 1m
A015DM5-C-0A100
-
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Band-On Telemetry System
-
Advanced Telemetrics International
The ATi Band-On Telemetry System transmits real-time sensor data from a rotating shaft while the system is running. The system consists of one or more rotating signal conditioner/ transmitter modules with battery pack and a stationary receiver. Rotating transmitters are available to interface with most any type of sensor including strain gages, thermocouples, thermistors, RTDs and accelerometers.
-
Product
Digital FM Telemetry
90332
-
The 90332 digital FM telemetry systems is designed to be used with full-bridge, strain gage sensors. The system features a miniature transmitter powered by a simple 9V battery, and a remote receiver capability of receiving the digital transmission over long distances. The digital technique eliminates many of the problems associated with traditional analog frequency modulated telemetry systems. Improvements with a digital technique include elimination of ripple, temperature drift characteristics, and higher signal resolution.
