Filter Results By:
Products
Applications
Manufacturers
Parametric Test
determine whether a DUT's electrical characteristics meet specification.
-
product
Massively Parallel Parametric Test System
P9001A
The highest throughput parallel parametric test solution. 100-pin parallel measurement capability and faster single parameter measurement than Keysight 4080. Good data correlation with Keysight 4080. New per-pin parametric test unit module with all basic measurement function (voltage, current, capacitance, pulse, frequency). Easy development of parallel test plan. Easy migration from 4080 environment. Proven in 1st-tier logic foundries and memory companies.
-
product
Wafer-Level Parametric Test
Wafer-level reliability engineers need to reduce test time without sacrificing measurement quality and accuracy.
-
product
DC Parametric Test System with Curve Trace
DC3
The wafer has been fully tested, cut and packaged. Today's IC manufacturers are finding tremendous cost savings in performing just fast DC tests on these packaged parts rather than running the full wafer tests all over again. Until now this required either an expensive full-power IC tester, or a "rack-n-stack" collection of instruments. Enter the HILEVEL DC3 Co-Optive Parametric Tester. No more instruments, no switching matrix, no tricky software. The DC3 combines a high-precision DC-PMU and internal DUT supplies to test up to 2,048 pins, all in a single chassis with Multi-Site capability up to 64 sites. And every DC3 includes our Classic Curve Trace feature, allowing easy curve tracing on every pin.
-
product
Cost-Effective ATE System
PRO RACK ATE
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
product
SoftTest Design Testing Services
We are a one-stop turn-key solution provider for the design, development, integration and support for Automated Test Systems. Our capabilities include Functional parametric and non-parametric test systems, intelligent go/no-go gauges, vision systems and a variety of fixtures and adaters to interface with the product under test the most efficient way possible. SofTest Designs can adapt the development architecture to meet the preferences or requirements of our customers in terms of instruments, interfaces and software. With our own in-house machine shop, our development and integration times are greatly reduced optimizing resources and transfering the benefits to our customer's applications.
-
product
Probe Card
VC43™/VC43EAF™
VC43™/VC43EAF™ probe cards offer a larger format version of the popular VC20. In addition to saving time, another advantage of the modularity is the ability to leave the interface in place and simply install the VC43™ topside using Celadon’s twist and lock insertion tool which minimizes the possibility of triboelectric or interconnect issues that can occur during typical probe card changes. The VC43™ can be used for production parametric test, modeling, characterization, and wafer level reliability testing. Cards can be configured up to 104 probes in either single or dual layer with near vertical probes to minimize scrub lengths on pads allowing the VC43s to probe pads as small as 30 microns.
-
product
Probe Card
Indexer™
The patented Indexer™ is the industry’s first automatic probe card changer designed for lights out parametric test.*Can support up to five VC20™’s with Advanced Cantilever™ technology, any variety*Card changes are complete in seconds*Fully programmable*Tested for hundreds of thousands of touchdowns.
-
product
Probe Card
VC20E Lab
*20 millimeter ceramic probe card*Optimized for DC parametric test, modeling and characterization, and single site WLR*Can be quickly installed using an interface tool into various interfaces and takes minimal storage space on the test floor*Effective operating temperature range from -65° to 200° C*Leakage as low as 5fA/V. If you require faster settling time, click here*Can be configured with up to 48 probes
-
product
EXG X-Series RF Analog Signal Generator, 9 kHz to 6 GHz
N5171B
Achieve faster throughput and greater uptime with the cost-effective performance optimized for manufacturing testPerform basic parametric testing of components and functional verification of receivers with industry-leading output powerThoroughly verify receiver performance by simulating complex analog modulation scenarios with multi-function generator capabilityMinimize downtime and expenses with self-maintenance solutions and low-cost repairs
-
product
Parametric Test Fixture
U2941A
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
product
PXI-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
778572-15
35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXI‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXI‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
product
LXI Reed Relay Matrix - Single 32x32 Plugin, Direct Y Access, 1 Analog Bus
65-227-001
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
LXI Reed Relay Matrix - Single 128x4 Plugin, Direct Y Access, 12 Analog Buses
65-221-002
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
256 Channel Power Supply
IDPS750
Salland Engineering’s Independent Device Power Supply (IDPS) can expand your existing Automated Test Equipment (ATE) with up to 256 independent DPS sources to increase parallel testing. It offers Force Voltage (FV) and Measure Current (MI) that can be used for continuity tests, parametric supply current (IDD) and quiescent supply current (IDDQ) measurements or simply for powering devices under test. The IDPS750 is targeted to reduce test costs for a wide range of applications including smart cards, memory, microprocessors and FPGA’s. Its design makes it useful in applications where many resources are required, or were the original ATE supplies do not meet your required specifications.
-
product
Test System
ITC57300
The ITC57300 Dynamic Parametric Test System mainframe accepts Test Heads that perform nondestructive transient measurements on semiconductor devices such as Insulated Gate Bipolar Transistors (IGBT), power MOSFETs, diodes, and other bipolar devices(requires additional optional bias power supplies and custom personality boards). Included in the mainframe are all test equipment and software necessary to analyze and perform resistive and inductive switching time, switching losses, gate charge, Trr/Qrr, and other transient tests.
-
product
EXG X-Series Microwave Analog Signal Generator, 9 kHz to 40 GHz
N5173B
Balance budget & performance to address parametric testing of microwave components & receiversPerform LO up conversion for microwave backhaul links or CW blocking for receiver testingMaximize test throughput with 600-s frequency switchingCharacterize microwave filters & amplifiers with the best combination of output power, low harmonics & full step attenuationUse as a high-stability system reference: the standard high-performance OCXO has an aging rate of 5x10-10 parts/day
-
product
Multi-Wafer Test & Burn-in System
FOX-XP
The key features of the new FOX-XP test cell that contribute to the cost-effectiveness of the solution include the ability to provide up to 2,048 "Universal Channels" per wafer, which allows the system to test all the devices on the wafer in parallel. The new "Universal Channel" architecture allows any channel to be any function (I/O, Device Power Supply (DPS) or Per-pin Precision Measurement Unit (PPMU)). This enhanced architecture now allows customers to perform per pin parametric testing, more extensive digital pattern test with deeper data stimulus / capture memory (32M per pin), and deeper scan (768M) optimized for BIST/DFT testing.
-
product
Advanced Circuit Card Automated Test
ACCAT
The ACCAT is designed to support diagnostic and acceptance test requirements across a wide spectrum of testing parameters. ACCAT provides a suite of core parametric test instruments, advanced GUI based software, Huntron Access Robotic probing and Huntron Analog Signature Analysis (ASA). ACCAT provides stimulus and asurement capabilities necessary for full functional and parametric testing of circuit card assemblies along with robotic guided probes for fault verification and debug. The Huntron ASA test is ideal for pretest or safe to power up procedures protecting the integrity of the test system.
-
product
RF Bias Burn-In System
These systems deliver an unbeatable combination of advantages over a wide range of RF frequencies and power levels. The Automated Multi-Channel RF-Biased Burn-In Test System is a turnkey system that incorporates all of the capability needed for accelerated aging and parametric testing of RF semiconductor devices. Its powerful software elegantly supports data acquisition, storage, and presentation. Accel RF’s customers choose system features to meet their technical needs and capital budget. In addition to cost savings, use of Accel-RF’s solutions accelerate product time-to-market, saving many months of product development.
-
product
EXG Signal Generators
The cost-effective EXG X-Series signal generators address critical speed and uptime needs for manufacturing test. With analog and vector models, the EXG provides the signals you will need for basic parametric testing of components and functional verification of receivers.
-
product
Dynamic Digital I/O With Per Channel Timing, Programmable Logic Levels And PMU PXI Card
GX5296
The GX5296 offers advanced dynamic digital I/O performance and capabilities in a single slot, 3U PXI format. The 32-channel, GX5296 features timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability to emulate and test complex digital busses for system, board or device test applications. Offering sub-nanosecond edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
product
LXI Reed Relay Matrix - Single 64x8 Plugin, No Direct Y Access, 6 Analog Buses
65-223-102
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
192 Channel Power Supply
HDPMU
Today cost efficiency is more important than ever. Many manufacturers are working on maximizing multi-site testing. Often maximization can’t be done because of limited tester resources. Salland’s HDPMU gives you up to 192 additional independent parametric measurement units (PMU) channels on a single board. Our solution will increase parallel testing without the need for creating complex device interface board (DIB). It can be used for continuity, functional or parametric tests or simply for device setup or loading. Full integration with the Teradyne IG-XL™ Software, easy set-up and high parallel measurement capability will reduce test costs significantly.
-
product
Universal Launcher Test Set
TS-217
The TS-217 is an I-level and Depot-level Universal Launcher test set supporting fighter aircraft launchers including the LAU-127, LAU-128, and LAU-129 (AMRAAM), LAU-117 and LAU-88 (Maverick), and LAU-7 (Sidewinder) missile launchers, launcher electronic assemblies, launcher power supplies, and circuit cards. The TS-217 is also used as a depot-level tester for F-18 armament including launchers (LAU-127, LAU-7, LAU-115, and LAU-116), bomb racks (BRU-32), and aircraft pylons (SUU-62 and SUU-63). Additionally, the TS-217 supports MAU-169 Paveway kits, subassemblies, and circuit cards. The TS-217 performs full parametric functional testing as well as troubleshooting to the faulty LRU (I-Level configuration) and SRU (Depot-Level configuration). The TS-217 can be used as an I-Level tester or as a Depot / Acceptance tester for launcher subassemblies.
-
product
Digital I/O with Per Channel Timing, Programmable Logic Levels and PMU PXI Card
GX5296
The GX5296 offers the most performance and features of any 3U PXI dynamic digital I/O board on the market today. The 32-channel, GX5296 offers timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability emulate and test complex digital busses for system, board or device test applications. Offering 1 ns edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level).
-
product
DDR4 Parametric Test Reference Solution
Keysight's DDR4 parametric test reference solution helps verify the signal integrity of DDR4 memory designs according to JEDEC specifications.
-
product
EXG X-Series RF Vector Signal Generator, 9 kHz to 6 GHz
N5172B
Achieve faster throughput and greater uptime with cost-effective performance optimized for manufacturing testPerform basic parametric testing of components and functional verification of receivers with industry-leading ACPR, EVM, and output powerReduce the time you spend on signal creation with Signal Studio software; purchase only the waveforms you need with 5- and 50-pack licensingMinimize downtime and expenses with self-maintenance solutions and low-cost repairs
-
product
LXI Reed Relay Matrix - Single 128x4 Plugin, No Direct Y Access, 6 Analog Buses
65-221-112
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
Test Fixtures
Pneumatically actuated Kelvin connection to custom manufactured device inserts either to complement ART's wide range of precision parametric test equipment or for use with third party measurement hardware.
-
product
LXI Reed Relay Matrix - Single 128x4 Plugin, No Direct Y Access, 12 Analog Buses
65-221-102
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
