-
product
AC Electronic Load
The electronic AC loads cover a wide variety of different voltage, current and power ranges. All the AC loads are programmed with 11 different sine, square and DC waves. With 5 crest factor variations of each, a total of 55 waveforms are available. An external input is also provided to enable the user to amplify signals from a waveform generator.AC Loads allow real world operating conditions to be simulated. Typical applications include circuit breaker, transformer & UPS output testing along with general laboratory and research work.
-
product
Interface Board, 8:1 USB
40-965-903
Converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 8 USB type A and 1 USB type B connectors. Allows the multiplexing of up to 8 USB1 or USB2 signals.
-
product
Power Interface Board 3U, 1PSU connector
106PIBM301-0000R
The PIB 3U 1 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
Digital Backplane Interface Board
MSXB 033
The Microstar Laboratories Digital Backplane Interface Board, part number MSXB 033, interfaces the Digital Backplane with a Data Acquisition Processor. The Digital Backplane Interface Board must be installed in the Digital Backplane to connect the backplane to a Data Acquisition Processor.
-
-
product
Thunderbolt V-600 Board 8-Slot
The 6U VME Thunderbolt boards provide optimal performance and reliability. The Thunderbolt V-600, configured with one Compute Module of four MPC7410 processors, provides 16 GFLOPS of computational performance per 6U VME slot. Data is transferred throughout the Thunderbolt over the SKYchannel Packet Bus. Data moves transparently through the SKYchannel P2 interface to other boards in a SKYchannel chassis.
-
product
RTM Analog Signal Conditioning Board
MS 3633I
CPCI Rear IO Analog Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on all type of Analog input and output interface including signal conditioning from ACIO board to Rear IO interface. Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
product
4k/HD Frame Memory Board
GG-170
The successor to the popular GG-167-HD/4K, this is an uncompressed HD/4K video input and output compliant frame memory board.
-
product
Multipurpose Debug Board For EC
DB30 x86 Debug Module
The DB30 x86 Debug Card is designed for debugging of COM Express modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
product
PC/104 Single Board Computer with Vortex86DX3 System-on-Chip
CM1-86DX3
The CoreModule CM1-86DX3 is a PC/104 board with DMP Vortex86-DX3 single chip solution and has a very good performance to power ratio. The board comprises all peripherals needed for an embedded PC on a small 3.775" by 4.050" printed circuit board. The CM1-86DX3 integrates a powerful yet efficient DMP Vortex86DX3 with graphic controller and audio controller together with an additional GBit Ethernet controller to form a complete PC, with all the standard peripherals already onboard. Two Ethernet ports (1x GBit and 1x 100MBit), four RS232/RS422/RS485 serial ports, two USB 2.0 host controller to handle the communication with external devices. There are PS/2 connectors for keyboard and mouse. A first generation SATA interface allows the connection of hard disk or CD drive. CFast is also available. System expansion can easily be realized over the PC/104 bus connectors.
-
product
Battery Load Bank
K-3980
Kongter Test & Measurement Co., Limited
Kongter offers a series of customized DC load banks with many different models for constant current battery discharge test and battery capacity test. They cover a wide voltage range from 12V to 480V nominal voltages with current up to 600A. They are widely applied in various industries. With its optional battery Data Acquisition Case (DAC), discharge values of EACH cell could be monitored in battery load bank and PC software simultaneously by using Kongter’s data view software.
-
product
Heavy Load Ball Screw with Caged Ball Structur
HBN
Heavy Load Ball Screw with Caged Ball Structure. Heavy load ball screws with the caged ball structure (HBN model) drastically improve the rated load compared to the conventional products by utilizing the optimum internal structure for use in heavy load condition. In this model, the caged ball structure is adopted between balls to eliminate collisions and mutual frictions of the balls and improve the lubricant maintenance. This modification brings about a longer lifetime under heavy load conditions.
-
product
Single Point Aluminium Load Cell
EST-3
Technopark Automation & Control
The EST-3 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 400x400mm. It is also an ideal load cell to use on filling machines and conveyor belt scale applications. This load cell is available in capacities from 60kg to 1000kg.
-
product
3U OpenVPX Multifunction I/O Board
68G5
NAI’s latest generation 3U OpenVPX Multifunction I/O and Communications Board, the 68G5, can be configured with up to three intelligent function modules. Ideally suited for rugged military, industrial, and commercial applications, this low-power/high-performance board delivers off-the-shelf solutions that accelerate deployment of SWaP-C optimized systems.
-
product
Button Load Cell
3000 Series
Button Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type provides a range of capacities up to 150 kN or 30 klb with better than ±0.5% (full scale) non-linearity. Three tapped holes are provided on the underside for ease of mounting. Fully welded cover, amplified and digitised versions are available on request.
-
product
LED Load Simulator
63110A/ 63113A/63115A
As shown on the V-I curve in figure 1, the LED has a forward voltage VF and a operating resistance (Rd). When using a resistor as loading, the V-I curve of the resistor is not able to simulate the V-I curve of the LED as shown in blue on figure 1. This may cause the LED driver to not start up due to the difference in V-I characteristic between the resistors and the LEDs. When using Electronic Loads, the CR and CV mode settings are set for when the LED is under stable operation and therefore, is unable to simulate turn on or PWM brightness control characteristics. This may cause the LED driver to function improperly or trigger it’s protection circuits. These testing requirements can be achieved when using a LEDs as a load; however, issues regarding the LED aging as well as different LED drivers may require different types of LEDs or a number of LEDs. This makes it inconvenient for mass production testing.
-
product
AC & DC Electronic Load
3270 Series （350V,1875W~22500W）
3270 Series is suitable for the step, square and sine wave of the AC Power device test, especially for the uninterruptible power supply UPS, Inverter, fuses, circuit breakers, power regulator AVR, battery, AC / DC power supply / components ... and so on, absolutely is the best test solution in the market.
-
product
600 Watt DC Electronic Load Mainframe
N3301A
The Keysight N3301A is a half-rack width mainframe with 2-slots that accepts combinations of N330x user-installable load modules (150 W to 600 W) for easy system configuration and future reconfiguration. The N3301A holds up to two N3302A, N3303A, N3304A, and N3307A load modules, or one N3305A and N3306A load modules, allowing up to 600 watts of total maximum power.
-
product
Signal Processor Board
MS 1532
- Frequency coverage from 5 kHz to 30 MHz in 1-Hz steps- High dynamic range: +30 dBm 3rd-order intercept typical- Digital filtering provides 58 IFBWs from 56 Hz to 8.0 kHz with exceptional shape factors- AM, Synchronous AM, FM, CW, USB, LSB & ISB detection modes standard- Tunable notch filter- Fast, flexible scanning with 100 memory channels- Large readable LED displays & user-friendly controls- Noise blanking & pass band tuning- Internal switchable preamplifier & attenuator- Operator-selectable RS-232, RS-485, or- RS-422 remote control- Viretx 5 FPGA based design (Two virtex for image processing)- LPC2468 ARM 7 Processor based design- MIL1553B and RS485 Interface- Two High speed 14 bit ADC (125MSPS) for I & Q Sampling- Direct sampling 2-30MHz- Audio CODEC- Conduction Cooled Board
-
product
PCI Counter/Timer with Quadrature Board
APC483
Several models with a variety of configurations provide up to ten counter/timer channels for counting events, generating waveform control signals, measuring pulse-widths, periodic rates, or quadrature position and monitoring operations.
-
product
Heat Exchangers RF Coaxial Loads
86500 Series
The 86500 Series Heat Exchangers are ideal for areas where water is limited. The loads are rugged, self-contained, easily operated, and portable units capable of dissipating up to 80 kW of RF power from DC to 800 MHz with a VSWR of 1.10:1.
-
product
6U VPX Ethernet + SRIO Switch Board
VP68803
LinkedHope Intelligent Technologies Co.,Ltd.
VP68803 is 6U VPX Ethernet + SRIO switch board compliant with VITA46 and VITA65 specifications, and is mainly applied for high-speed data exchange and routing between different boards in a VPX chassis. Designed with 6U VPX form factor, VP68803 has excellent performance in thermal dissipation and environment protection.Integrated with Ethernet, SRIO switching and routing, VP68803 has 20 1000Base-BX Ethernet interfaces for control plane, and has 19 x4 SRIO 2.1 ports for data exchange. Therefore, VP68803 realizes internal and external data transmission with comprehensive integration. Besides, VP68803 can be installed in Single-Star Topology and Dual-Star Topology backplanes. These characteristics guarantee the stability and applicability of VP68803.
-
product
VXI Register Interface Board
VXI-5524A-3
* 3.3V power out instead of 5 V on Digital IO bus connector* All othe specifications same as listed above for the VXI-5524A board.
-
product
Load Banks
PARELO
Amfax introduce the latest generation of load banks we affectionately call PARELO. This range of load banks provides a combination of high performance passive resistive loads along with extreme flexibility of use. This is achieved by our unique FLEXI-phase Switching(TM) technology.. Designed primarily for offering high wattage loads for the aerospace, energy, automotive and transport sectors. PARELO load banks are a cost effective solution for companies requiring high wattage loads when testing their products.
-
product
MicroComU Board
The MicroComU board is designed to facilitate the adoption and use of the microDXP. To this end, the MicroComU includes various features to support and extend the functionality of the MicroDXP board. The MicroComU is designed to mate to a MicroDXP and be used as a set.
-
product
6U VPX Processor Board
VP62110
LinkedHope Intelligent Technologies Co.,Ltd.
VP62110 is a 6U VPX board based on Intel® Xeon® D-15xx processors, with more than 7-year life cycle. Supporting up to Intel® Xeon® D-1577 (16x 1.3GHz) processor, VP62110 is able to perform vector operation and floating point arithmetic that require high throughput. Besides, VP62110 supports Intel® Turbo Boost, with the processing speed of CPU up to 2.7GHz. The high-performance CPU and the Turbo Boost technology leave no worries for extra cost and complexity of system settings.
-
product
Triple-Axis Gyro Breakout Board
L3GD20H
A gyroscope is a type of sensor that can sense twisting and turning motions. Often paired with an accelerometer, you can use these to do 3D motion capture and inertial measurement (that is - you can tell how an object is moving!) As these sensors become more popular and easier to manufacture, the prices for them have dropped to the point where you can easily afford a triple-axis gyro! Only a decade ago, this space-tech sensor would have been hundreds of dollars.
-
product
PCIe Carrier Board for SOM3
Solar Express 215 (SE215)
Sundance Multiprocessor Technology Ltd.
SE215 is a development board for Sundance SOM3 . It is a PCIe X1 Gen2 carrier card with one site for an SOM3. It offers USB JTAG and UART, through a micro USB connector, Display port and comes with a version of Display port IP core for SOM3 from Bitec DSP. The card provides Power GOOD and user LEDs for rapid debugging.
-
product
Coaxial Loads
Loads are supplied standard with N connectors, which are recommended above 500 MHz.
-
product
1800 Watt DC Electronic Load Mainframe
N3300A
The Keysight N3300A is a full-rack width mainframe with 6-slots that accepts combinations of N330x user-installable load modules (150 W to 600 W) for easy system configuration and future reconfiguration. The N3300A holds up to six N3302A, N3303A, N3304A, N3307A load modules, or three N3305A, N3306A double-wide modules, allowing a total up to 1,800 watts of maximum power.
