-
product
Bending Drain
With the Bending Drain you measure the shrinkage and bending of building materials. Also you may simulate with a built in electrical heating a real world floor heating.
-
product
Pure Bending Fatigue Teesting System
PQ-6
Jinan Testing Equipment IE Corporation
PQ-6 Pure Bending Fatigue Testing Machine is suitable for testing the fatigue strength of metals and other materials under bending & rotating.
-
product
Power Cord Bending Tester
SW-6
SW-6 Power cord bending tester is fully designed according to the IEC standard, and can also be costumer-sized depends on the samples’ type and the costumer’s requirement. Specifications: • Power supply：AC220V 50/60HZ 12KVA • Control mode: PLC with touch screen and Servo motor. • Test Speed: 10~60times/min (Adjustable) • Test Degree: 0~540° (Adjustable) • Counter: 0~999999 (Can be pre-set) • Weight: 5N,10N,20N. 2Sets. (6Position type will have 6 Sets) • Position: 2/6 • Load Current: 0~20A (Adjustable) • Angle plate: Can check the test situation • Sample fixture: Can be costumer-sized. • Can do power line bending test (The User need prepare sample and power supply ), Can record the number of the sample’s work with load.
-
product
Motorized Bending Testing Machine
GW-A Series
Jinan Testing Equipment IE Corporation
GW-A series motorized bending testing machines are special equipment for bending test on reinforce bar, steel bar, and pipe etc. The motorized bending testing machine can do bending test in both directions according to the standard requirement. The motorized bending tester conforms to standards including ASTM A615, ASTM A615M, ISO 7438, and ISO8491 (E) etc.
-
product
Bending Test Machines
Infinity Machine International Inc.
Bending Test Machines by Infinity Machine International Inc. - for applications such as bending cycle test machine wire wing left and right tester, 90° 180° bending wire swing test left and right optical cable repeated bend testing machine, cable bending durability tester, cable flex bending test machine, high precision bending test machines, and more.
-
product
Printed Circuit Board Bending Test Jig
Evaluation of Bending Strength of Electronic Components and Substrates
-
-
product
Economical Single Point Bending Beam Load Cells
ESP SERIES
The ESP Series is a economical, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point bending beam design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The ESP Series features a moisture proof sealant.
-
product
IEC60884 Plug Power Cord Bending Test Machine
CX-YB06
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 plug power cord bending test machineThe power cord bending tester is used to bend (bend) the power cords of non-reconnectable plugs and household appliances and similar appliances.It complies with UL817, VDE0620, IEC60884-2006 Figure 21, and other standard requirements.The device can preset the number of tests (up to 999999 times), the test is automatically carried out, and when the te
-
product
Computer Controlled Electro-hydraulic Servo Bending Testing Machine
SBT Series
Jinan Testing Equipment IE Corporation
SBT series computerized bending testing machines are mainly used for bending and pressing tests for metallic sheet & round bars as per standards of GB/T232-2010 & ISO 7438-2005 Metallic Materials-Bend Test. An axial oil cylinder for bending test is installed on the top cross-head. Two pressing oil cylinders are installed at both sides of the frame, which adopts the synchronous control, to realize the pushing and pressing force on the bending support to adjust the distance between pivots. The pressure meter indicates the pressure in bending or pressing. Various load display can be selected, such as display through the pressure meter, digital display, and computer screen display etc. The computer control type SBT bending testing machine can do the bending test automatically or manually. TThe applies bending force can be adjusted or controlling the oil feed valve.
-
product
Economical Bending Beam Load Cells
EBB SERIES
The EBB Series is a economical low capacity bending beam load cell suitable for use in a variety of industrial and OEM force measurement and weighing applications. It is made of an aluminum alloy and comes in 1, 2, 5 and 10 kilogram ranges.
-
product
Fully Automatic Plastic Tensile/Bending Testing Machine
This is a fully automatic tensile and bending tester for plastics. It is capable of continuous operation from measurement of specimen dimensions, supply, and data processing.
-
product
Bending Beam Load Cell
Futek Advanced Sensor Technology, Inc.
Are the best fit for many measuring tasks. Here, the signal, on principle, depends on the bending moment.
-
product
Load Cells
For use in harsh environments, our Models T66 (bending beam),T85 and T85-T(shear beams)are manufactured fromstainless steel, fully welded and hermetically sealed to provide total environmental protection (IP68 and IP69K). The T85-Tmodel has a blind loading hole, ideal for use in platform scales.
-
product
Bending Deflectometers For ISO 178, JIS K 7171, And ASTM D790 Compliant Testing
After tensile testing, flexural tests are the most common strength tests for plastics and other resins. The main standards for plastic flexural (bend) tests are ISO 178, JIS K 7171, and ASTM D790, which require very accurate test systems. These standards include flexural strain measurements using a deflectometer, ranging from micro-strain measurements in the elastic region, the reversible elongation at the beginning of tests, to larger strain measurements in the plastic region. Shimadzu's deflectometers integrate easily into AG-X plus series, AGS-X series, and EZ-X test frames and Trapezium X testing software. Since these deflectometers push up against the specimen from below, the specimen color is not a limiting factor, as can be for laser type non-contact deflectometers. Furthermore, these deflectometers can partially absorb the shock during specimen failure, preventing specimen fragments from scattering.
-
product
Cold Bend Testing Machine
QualiBend Series
The Cold Bend Testing Machine - QualiBend series are used for bending of metallic materials such as metal rods, planks and steel screw threads. The machines operate with a hydraulic loading system to adjust the distance of the cold-bending press roll to drive the rod in both directions making the cold bending press roll forward and back.
-
product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131G
The Keysight 85131G is a 53 cm (21 in) long1 semi-rigid cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss of 16 dB or better. Insertion loss is 0.3 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 4 inch radius. Stability1 of the Keysight 85131G is 0.06 dB and phase is 0.16o * f + 0.5o (where f is frequency in GHz).
-
product
Fiber Stiffness Tester
DRK023B
Shandong Drick Instruments Co., Ltd.
Used to determine the bending properties of various fibers.
-
product
Optical Fiber Identifier
AFI-500
Shanghai Fibretool Technology Co.,Ltd.
AFI-500 Optical Fiber Identifier can quickly identify the direction of transmitted fiber and display the relative core power without any damages to the bended fiber. When the traffice is present,the intermittently audible tone is activated.
-
product
Flexible AC/DC Current Tester
FCM-400
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Bending free flexible clamp sensor*Measuring ranges AC/DC 0.100A～300A(Min. resolution 0.001A)*Big CT window (φ450mm)*Easy accessibility to the hard to clamp object
-
product
H Bend Waveguides
H-plane waveguide bends are sections of high-precision crafted waveguides and shaped to either 30º, 45º ,60º, or 90º angles. It directs the radio frequency beam and "bends" the signal to go the direction you want.View more H-Bend Waveguide
-
product
R&D Clamshell Bed of Nails Testers
Rand Press Rods Family
Designed for Research & Development and Pre-Production environments to support often reoccurring product design changes. The primary design focus for this fixture is ease in applying engineering changes and resilience to the abuse of applying multiple engineering changes without damage. In R&D and Preproduction, design changes and updates can occur every week. This Rand fixture, unlike normal test fixtures was designed to be easily taken apart and updated. Constantly disassembling modifying and reassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for multiple updates requiring machining, drilling and wiring changes.
-
product
Resonant Testing System
Originally designed to precrack specimens for fracture mechanics, the current versions offer much more possibilities due to a modular concept:*Bending up to 160 Nm*Tension/Compression up to 8 kN*Torsion
-
product
Bi-Directional-Coaxial LD/PD Module
BiDi-F1000 (FTTx)
Hangzhou Huatai Optic Tech. Co., Ltd.
Laser optical: DFB or FP. DFB laser optical: with isolation or without isolation. Low threshold current and operating current. High output power. Built-in InGaAsP monitor PD. High responsivity, InGaAs planar PIN detector. Wide temperature range operation(Tc=-40℃to+85℃). Fiber ITU-T G.657 Bending low loss, fiber optic cable features
-
product
2.5mm Visual Fault Locator
3105
Anfkom International Co.,Limited
The 3105 Pen type VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network. It includes:Finding the breakpoint, poor connections, bending or cracking in fiber optic cables.Finding the faults of OTDR dead zoneEnd-to-end visual fiber identification
-
product
Flexible Cable Set, 3.5 Mm (Test Port) To 7 Mm
85132F
The Keysight 85132F is a 62.9 cm (24.75 in) long¹ flexible cable set composed of two 3.5 mm female² to 7 mm connectors. Cable frequency range is dc to 18 GHz with a return loss greater than or equal to 17 dB. Insertion loss is 0.25 * sqrt(f) + 0.2, where f is frequency in GHz, for the test port connector and device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability¹ of the Keysight 85132F is less than 0.12 dB and phase is 0.13 * f + 0.5, where f is frequency in GHz.
-
product
3x3 and 2x2 High NA Couplers
Feasa produces a range of Couplers Manufactured from high Numerical Aperture (NA) 80 micron fiber. High NA fiber has low bend attenuation compared to standard singlemode fiber.
-
product
Waveguide Directional Couplers
WR-42 to WR-10 waveguide sizes. Split block waveguide versions available. Available in 7 bands including K, Ka, Q, U, V, E, W from 18 GHz to 110 GHz. 30 dB typical directivity. E Bend and H Bend configurations available. 10 dB and 20 dB coupling values are offered.
-
product
ITA, I2 MX, EMI, XL Backshell (XL Bend Radius and Cable Exit)
410130126
This model i2 MX includes the backshell only and does not include module inserts or front protective cover. The XL-size backshell allows for a greater cable bend radius and large cable exit. The max cable bundle eff diameter= 1.67".
-
product
Telescopic AC Voltage Detector
*Non-contact AC voltage detection*Telescopic length 1.3M*Check AC voltage :** Behind the wardrobe** Inside false ceiling**Under ceiling** Low location or ground floor*No need to bend down while checking*Battery powered : 2 x 1.5V (L736 / LR41 / AG3)*Worldwide patent pending*Originated, designed and developed by MEET
