Waterproof Test Chambers
-
Product
HALT/HASS Testing
HALT HASS Chamber
-
AST applies stresses (such as temperature and vibration) to products well beyond its normal use environment. This type of testing is done to determine product operating and destruct limits. These stresses are applied as the product is functionally tested and continuously monitored for failures.Highly Accelerated Stress Testing (HALT) and Highly Accelerated Stress Screening (HASS) are two types of accelerated stress testing. These types of tests are commonly used to eliminate design problems, helping to develop a robust, mature product prior to market introduction. It can also be used to screen out infant mortality issues prior to shipment.
-
Product
Encoder Testing
-
HEIDENHAIN offers testing and inspection devices for the adjustment and fault diagnosis of its encoders. The highly accurate inspection devices are universally deployable, capable of being calibrated and interposed within the closed control loop. The testing devices are primarily used for the functional testing and adjustment of encoders. HEIDENHAIN encoders deliver all of the setup, monitoring, and diagnostic data needed.
-
Product
Display Test System
-
PIMACS provides the broadest range of display optical performance measurement system for optical testing of various samples including flat panel displays. We are specialized in testing all sizes of display modules and panels ranging from various field.
-
-
Product
Test Contactor
MiCon
-
The MiCon™ Test Contactor is spring pin footprint compatible supporting advanced temperature requirements as well as advanced power/current requirements. The footprint compatibility allows for easy and cost-efficient conversion from spring pin setups. The fully decoupled load board side of the spring ensure no degradation of the load board pad.MiCon features a single piece design, which ensures a long lifespan, low and stable contact resistance, high current carrying capability and an extended temperature range. The MiCon allows for testing at full specification values. The extended operating range accommodates device lead trim and form variability such as device alignment accuracy and device lead coplanarity.
-
Product
Testing Solutions
-
Within the test strategy the final functional test complements the quality strategy. Therefore meaningful results of functional tests shouldn't be focused only on good/bad selection. Goal is to get correct data for statitistics and trend analysis.Under economical point of view you should consider following points as very important in test conceptions:Stability of measurementsAccuracyand the throughput
-
Product
Magnetic-Inductive Testing
MAGNATEST® Product Family
-
Foerster Instruments, Incorporated
The MAGNATEST product family is used for the non-destructive testing of metallic materials for magnetic and/or electrical properties. The test instruments are used in the automotive and aviation sectors as well as in the production of semi-finished products. The focus is on testing components relevant to safety such as brake discs, or ball pins and functional components such as camshafts and drive shafts, pivots and piston pins. Typical test tasks include hardness checks, material differentiation and sorting. MAGNATEST can also be used for the automatic testing for the geometric properties of all metallic series components. The high-performance amplifier installed in MAGNATEST test instruments makes it possible to analyze harmonics, which guarantees an extremely reliable and precise repetition, even when impacted by perturbations.
-
Product
Protection Device Testing
-
The Motwane Manufacturing Company
Power system protection is a branch of electrical power engineering that focuses on protecting electrical power systems to detect and isolate faulty parts. The objective is to keep the power system stable by separating only the defective components while keeping the rest of the network in operation. The device protects the transmission lines, generator transformer, and other electrical apparatus from multiple faults.
-
Product
HARDNESS TESTING
-
Hardness testing is a basic test used to verify raw materials or as a quick check for materials that fail or aren't performing as expected. Hardness tests quantify the resistance of a material to plastic deformation and is available as microindentation or macroindentation.
-
Product
Torque Testing
-
Torque testers measure properties such as torsional strength and stiffness and are used in quality control of various fields including medical devices, metals, and aerospace
-
Product
Signaling Test Solution
IQcell-5G
-
Purpose built to validate RF parametric measurements, end-to-end throughput, MIMO, mobility, and user experience testing across cellular and cellular capable connectivity devices such as smartphones, CPE’s, laptops, tablets, hotspots & much more.
-
-
Product
Automated Test Equipment
-
Viewpoint Systems offers design verification and manufacturing quality inspection systems to help customers reduce human error in repetitive tests, increase testing speeds, and ultimately get products to market faster at a lower cost. Viewpoint Transforms Test from Design to End-of-Line. Our R&D test systems are designed with the flexibility to validate ever-changing prototypes while accelerating your development schedule.
-
Product
Phase Noise Testing
-
The systems are based in the UK although testing for any company world wide will be undertaken.
-
Product
Automated Aerospace and Defense Test
test
Obsolescence management, evolving RF requirements, and design for test (DFT) challenges every test organization in the aerospace and defense industry. Organizations are transitioning from rack-and-stack box instruments and closed-architecture automated test equipment (ATE) systems to smarter test systems built on a modular platform that scales to meet current and future needs.
-
Product
Linemen's Test Set
TeleTalker 330
-
Triplett Test Equipment & Tools
The Triplett TeleTalker™ 330 is a high performance lineman's test set with a weather resistant seal. This butt set offers many standard features not found on more expensive models like dedicated store / redial buttons, adjustable volume, Pulse and Tone dialing, and more. The high impact and weather resistant case allows for this product to be used in all demanding industry settings and features a full 3 year warranty. The user-friendly layout helps installers get the job done effectively with ease. The TeleTalker™ 330 requires no battery for main use and can store up to 10 frequently dialed numbers. Complete with angled bed of nails (JS Popper) test clips.
-
Product
EMI/EMC Testing
-
EMI/EMC testing can reliably predict product performance in any electromagnetic environment. Testing can also determine the possibility of interference with other equipment, possibly degrading performance. Testing may be required in order to comply with regulations or for informational and product improvement purposes.
-
Product
RADAR Stability Testing
PN9002
-
Radar component and system testing usually evokes images of complex, expensive measurement systems occupying multiple equipment racks. In some cases, radar equipment designers have even used entire radar systems as a proving ground for their new components and modules. With the introduction of the PN9002 pulse-to-pulse radar stability test set from Noise eXtended Technologies , radar testing has become significantly less complex and costly. The modular PN9002 system provides outstanding dynamic range at frequencies from 2 to 18 GHz and optionally from 0.4 to 18 GHz.
-
Product
Vibration Test Technology
-
These vibration exciters (also called shakers) use permanent magnets and are available as portable and stationary systems for simulating ambient vibration conditions. Robust design ensures a long service life, and typical applications include structure analysis and testing smaller subassemblies. These shakers are characterized by high lateral and axial stiffness and come in lightweight construction as specified by industrial users.
-
Product
Test Set
TS® 19
-
The Fluke Networks TS19 Test Set combines all the essential test set features at an affordable price. This test set was specifically designed for in-house telecom technicians. Its high impedance monitor prevents accidental disruption of service from clipping onto a data line while in monitor mode, thus ensuring the integrity of critical data lines.
-
Product
Waterproof Infra-Red Turbidimeter (NTU) with calibration kit
TN 100
-
The microprocessor-based waterproof TN100 meter is an easy-to-use turbidimeter that meets the rigor of rugged field applications. It is a "must -have" for anyone monitoring turbidity on the go. Using an Infrared light source, it delivers laboratory accuracy with a resolution of 0.01 NTU across an extended range of up to 20 NTU (Nephelometric Turbidity Units).
-
Product
Yellowing Resistance Chamber
-
Sataton Instruments Technology CO., Ltd
Yellowing resistance chamber also called as discoloration meter is the professional testing instrument for measurement of yellow resistance performance by simulating sunlight. It is a useful tool for testing the yellowing resistance property of light color materials or products such as white thermoplastic polyurethane elastomer shoe sole or light synthetic materials. The chamber can also be used for printing and packaging industry for deploying chemical dyes.
-
Product
Impact Testing
-
When you need to evaluate how your product & materials react to shock loading, Trialon is here to help. By utilizing our laser-aiming test stand to create consistent positioning and ball impact, you can trust that Trialon has the equipment and personnel to conduct your test accurately and timely.
-
Product
Simulation and Testing Solutions
LMS
-
Siemens Digital Industries Software
LMS simulation and testing solutions help manufacturing companies manage the complexities of tomorrow’s product development by incorporating model-based mechatronic simulation and advanced testing solutions in the product development process. Our products and services tune into mission-critical engineering attributes – ranging from system dynamics, structural integrity and sound quality to durability, safety and power consumption.
-
Product
Meter Testing
METES
-
Meter test systems with high accuracies of up to 0.02% and a wide measuring range for precise measurements in single- and three-phase applications. The meter test systems of the METES series are used to test the accuracy of Ferraris meters and electronic electricity meters under any operating conditions. The impact of system perturbations such as harmonics or flicker on the meter can be taken into consideration during tests.
-
Product
Ion Chambers
-
0.2 to 5000 mR/hr, 5 Ranges• Temperature Compensated• Retractable 1000 mg/cm² Beta Shield• High Background Zero Capability• Proportional Audio Output
-
Product
Hydrogen Testing Solutions
-
The widespread introduction of hydrogen is a necessary and essential part of the path to a climate-neutral future. AVL is ideally equipped to support and help shape this transfer. In terms of content, we provide extraordinary expertise in the fields of engineering, simulation and testing and act as a reliable innovation and development partner. With our test solutions, we support you specifically with your challenges, from development, through industrialization, to further operation. Depending on the technological maturity of your product, the test solutions offer you full flexibility within the planned development tasks or a customized proportion of supporting and automated functions, if quality assurance in the production environment is involved. The guarantee of safe operation is obligatory and is of course also mapped.
-
Product
Tensile Test Chamber
-
CSZ's Tensile Test Chamber is an environmental chamber that interfaces with a customer tensile tester load frame. This chamber is required to expose various materials and components to temperature conditions while undergoing tensile test. Tensile testing stresses materials by pushing, pulling, twisting, or bending intended for static and fatigue testing.
-
Product
Burn-In Test Fixtures
-
Burn-in generally involves the extended operation of a product in a temperature-controlled environment. With possible humidity and supply voltage margining - the burn-in process can then be extended to include power stress (levels and on/off cycles) tests, high humidity environmental simulation as well as the classic "four corner test" of high voltage + high temperature, high voltage + low temperature, low voltage + high temperature and low voltage + low temperature.
-
Product
Optics Test Systems
Electronic And Visual Autocollimators
-
Optik Elektronik Gerätetechnik GmbH
OEG GmbH specializes in the use of autocollimators, collimators and telescopes for special applications in optical measurement technology in the wavelength range from 380nm to 1550nm (SWIR).
