Screw
See Also: Thread, Linear Actuators
-
product
Wire Piercing Clips
619
This new clip makes wire piercing much easier. Just slide the wire into the cradle and screw the pin down into the wire. This method is clean and leaves minimal wire damage. If you have to proceed to pierce the wire, do it the right way with 619.
-
product
Ethernet Digital Interface OEM Board
8063
* Same Digital IO lines as standard 8063. * Same data transfer capabilities as standard 8063 * Digital I/O uses high-density DC-62 connector.* Power connections via 2 screw terminal strip or solder pads.* User configured IDN message and webserver pages makes board respond as part of your system.* Use an ICS Wiring Kit to extend the Ethernet signal to a rear panel RJ45 jack.* Runs on 9 to 32 Vdc power.
-
product
Polarization Controller and Scrambler - PXIe
Pol 1000 Series
The Pol 1000 Series PXIe module enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands. Pol 1000 Series can be used with our wide range of optical and electrical PXIe test modules, and can be used to build complete mixed-signal test platforms.
-
product
TB-2650, Screw Terminal, 8x64, 1-Wire PXI Module Matrix Terminal Block
781131-03
The TB-2650 provides the necessary routing to configure the PXI-2531 or PXIe-2531 PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2650 to the front panel I/O connectors of the PXI-2531 or PXIe-2531.
-
product
Twin columns automated force test stand 48" travel - 20,000 lb
720TN
The advanced 720TN Series Universal Test Systems are ball screw driven test stands, excellent for affordable, precision tensile and compression testing of a wide variety of materials, products or ASTM standards. These variable speed testers have increased speed ranges and include adjustable travel limit switches. With the unique dual testing area, users can setup for two tests, tensile and/or compression, without having to switch out fixtures.
-
product
AC/DC Power Supply 20 W
CFM21M120-S
AC/DC power supply with 20 W from Cincon | input ranges 90 - 264 VAC | output 12 V | operates in temperature from -25 to +70 °C | provides 2 MOOP safety and is class II | screw terminals
-
product
Fence Vibration Sensor
ENVIROMUX-FENCE1
Detects when individuals climb over or cut through chain link or wire mesh fences. Advanced built-in signal processor prevents false alarms. Four sensitivity settings to tune each sensor to a particular fence section and intrusion type. Two open-collector outputs – alarm and power failure. UV resistant case and epoxy sealed electronics provides maximum resistance to harsh environments. Rated NEMA 4X and UL94 5V. Use individually or chain units with each ranging from 40 to 60 feet away. Includes mounting brackets for installing the sensor to fence fabric. Screw terminals. Operating temperature: -4 to 131°F (-20 to 55°C). Operating voltage: 9-15V DC.
-
product
Signal, Module, ITA, QuadraPaddle, 90 Series, 480 Position, Unloaded
510151106
NOTE: Part # 510151106 Rev E and higher utilize captive screws that cannot be replaced with screws from currently VPC- offered screw kits.Primary mating module 510150116. (May mate with other Receiver modules, as well.)
-
product
Module Accessory Kit, Quantity 26, 4-40 x 1.250" Socket Head Cap Screws Stainless Steel
510109597
Used with modules: 510109315, 510150120, 510150125, 510150126, 510150127, 510150128, 510150141, 510150142, 510150143, 510150148, 510150152, 510150153, 510150154, 510150155, 510150210, 510150220, 510150227 and 510150238.
-
product
9-Pin D-Type Connector Block
40-965-009-M
Suitable for use on the front of modules this connector block provides a simple method of connecting to 9-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
product
Economical LED Display for Remote Annunciator Applications
AN-3100D-LC
LED Illumination for long life, low power Laser Printed window Legends Compact Size Barrier, screw terminal connection Panel or 19" Rack Mounting 4 Windows Sizes: 3x3, 1.5x3, 1x3, 1.5x1.5 Selectable Window Colors: White, Red, Blue, Green Amber Built-in Test Pushbutton option
-
product
Keying Pin Kit, Receiver/ITA
310118112
The Keying Pin kit is a way to avoid damaging the contacts within the ITAs and Receivers. Simply insert the longer keying pins into the receiver and the smaller set screws into the ITA to create the pattern needed to isolate your test fixtures so there is no operational mismatch.
-
product
Module Accessory Kit, Quantity 26 2-56 x .25" Flat Head Phillips Screws Stainless Steel
510109373
Used with modules: 510104249, 510104267 and 510104289.
-
product
Cable Assembly, 68 Pin Female SCSI (Thumb Screws), to 68 Pin Male SCSI (Spring Latch), 36"
515109120
Cable Assembly, 68 Pin Female SCSI (Thumb Screws), to 68 Pin Male SCSI (Spring Latch), 36"
-
product
Module Accessory Kit, Quantity 26 4-40 x .31" Flat Head Phillips Screws 100 Degree
510109371
Used with modules: 510104135.
-
product
Triaxial Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
Triaxial accelerometers are intended for simultaneous measurement of vibration in 3 perpendicular axis. All models have a central drilling for easy screw attachment and convenient axis alignment.
-
product
Module Accessory Kit, Quantity 26, 4-40 x .50" Socket Head Cap Screws Stainless Steel
510109495
Used with modules: 510108240.
-
product
TB-2634, Screw Terminal, Ribbon, 4x64, 1-Wire PXI Module Matrix Terminal Block
778840-01
Screw Terminal, Ribbon, 4x64, 1-Wire PXI Module Matrix Terminal Block - The TB-2634 provides the necessary routing to configure the PXI-2529 PXI Matrix Switch Module as a 1-wire 4×64 matrix. You can directly connect the TB-2634 to the front panel I/O connectors of the PXI-2529. The … TB-2634 includes ribbon cable headers that provide access to the rows and columns of the matrix.
-
product
68-Pin SCSI Micro-D Connector Block
44-965-068-F
Suitable for use on the front of PXI BRIC modules this connector block provides a simple method of connecting to high density 68-Pin SCSI Style Micro-D connectors. The screw terminals accept wires up to 20 AWG and use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
96-Pin Female DIN to 88-Pin Female Screw Terminal, 10 V, PXI Module Mount Terminal Block
781347-01
NI TB-4330 Terminal Block for PXIe-4330
-
product
37-Pin D-Type Male Connector Block
40-965-037-M
Suitable for use on the front of modules this connector block provides a simple method of connecting to 37-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
product
Automated Tuners / Impedance Tuners / Load Pull Tuners
MT97x, MT98x and XT98x series automated tuners (also known as automated impedance tuners and automated load pull tuners) are precision instruments that are optimized for a broad class of in-fixture and on-wafer applications, and may be used in any automated or manual application requiring the ability to match the impedance of a microwave circuit element or to establish specific impedances at a terminal interface. The tuner design is based on the slide screw concept using the inherently broadband slab-line transmission structure. Each unit has two non-contacting probes deliver high VSWR with superb accuracy and reliability over a wide frequency range. These probes can be fully retracted leaving a low-loss, well-matched transmission line, which is a significant benefit in power related applications where two-port tuners capable of handling large amounts of power are required. As integral components of Maury Device Characterization Solutions, these PC-based tuners are controlled using Maury's family of Device Characterization Software tools, including MT930 IVCAD, MT993 ATS and the DLL-based measurement automation environment. Maury Microwave automed impedance tuners are ideal for load pull, harmonic load pull, active load pull, hybrid active load pull, noise figure, noise parameters and all automated tuner applications.
-
product
Non-Driven Linear Actuators
Electrak PPA-M
Electrak PPA-M actuators are designed for robust and versatile multi-purpose functionality. With dual input shaft capability, these actuators are easily adaptable to customer-supplied motors and/or synchronous operation with multiple PPA-M units. Able to withstand harsh environments, these highly efficient ball screw units can be operated manually and are essentially maintenance free.
-
product
Module Accessory Kit, Quantity 26 2-56 x .187" Socket Head Cap Screws
510109305
Used with modules: 510104128, 510104133, 510104134, 510104135, 510104136, 510104139 and 510104261.
-
product
- RS-232 High Speed Line Driver with LCD Display
Model 227
FEATURES: DataSpy Status Display; Full Duplex to 5 Miles; Async, DC to 115.2 KBPS; Powered by TD; RJ-11 and Screw Terminals for the Line Interface; Built-in Surge Protection; Fully Compatible with Model 201 up to 19.2 K. The Model 227 RS-232 High Speed Line Driver with LCD Display provides full-duplex transmission from DC to 115.2 KBPS over two twisted pairs.
-
product
sbRIO-9223, Non-Enclosed, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
785480-01
Non-Enclosed, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO-9223 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The sbRIO-92233 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the sbRIO-9223: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
RS-232 Auto Powered Line Driver
Model 201
FEATURES: Operates with only Pins 2(TD), 3(RD), & 7(GND); Screw Terminals and RJ-11; DTE/DCE Switch; Built in Surge Protection; Male or Female RS-232; 19.2 KBPS, Full Duplex, 2.1 Miles. The Model 201 RS-232 Auto Powered Line Driver requires only TD, RD, and signal ground for power and full duplex operation up to 19.2 K BPS.
-
product
Posi Drives® (Lead Screw Driven)
Del-Tron's Posi-Drive™ lead screw actuators are compact and economical, taking the work out of designing linear motion systems. Available in 3 size profiles, our lead screw actuators require no alignment of components and install with standard fasteners. They are fitted with anti-backlash lead screws and multi-beam couplings with high speed misalignment capability and standard NEMA motor mounts. Available in one, two or three axis configurations these stages travel up to 12”.
-
product
Digital Tank Test Kit
4109
The voltmeter included in the kit, the “Model DPM” voltmeter, is designed for ease of use by meter readers and corrosion technicians alike and the voltmeter comes with an integrated RE-5 reference electrode attached for “metallic structure-to-soil” potential difference readings. The kit also includes a special test lead that has a brass thumb screw on one end which allows the test lead to substitute for the RE-5 reference electrode. This substitution allows the voltmeter to take “structure-to-structure” potential difference readings. The voltmeter offers two ranges, ±2VDC and ±20VDC with a 20MΩ input impedance. Since the voltmeter is digital [in contrast to the meter in our analog tank test kit (Cat. # 4108)], both negative and positive voltages are displayed. `
-
product
Vibration Sensor
ENVIROMUX-VSS
For registering movement and shocks. Adjustable sensitivity. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Regulatory approvals: RoHS.
