Simulators
create what could be.
See Also: Simulation, Simulation Software, Simulation Testing, Emulators
-
Product
Engine Torque Pulse Simulation
ETPS
-
HORIBA has revolutionized the way vehicle manufacturers test their Powertrains and Front End Accessory Devices. The ETPS dynamometer system accurately produces torsional pulse characteristics of an engine. This new technology employs a sophisticated mathematical model to calculate the resulting torque at the output of the engine based on engine and combustion process parameters.
-
Product
PXI Precision Resistor Module 9-Channel, 2 to 13.6k
40-297-031
Programmable Resistor Module
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Power Temperature Cycling
-
Typically, this test would be selected when during its normal operating activity, the device is subjected to high temperature excursions and is required to power on and off at all temperatures. The power and temperature cycling test will determine the ability of a device to withstand exposure to such temperature extremes with operating biases periodically applied and removed. The worst case conditions expected in a typical; application will be simulated.
-
Product
PCI High Density Potentiometer Card 2-Channel, 16-Bit, 0 To 65k Ohm
50-296A-021-2/16
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 10A Fault Insertion Switch 10-Chan 2-Bus
40-199-002
Fault Insertion Unit
The 40-199 is a 10 Channel Fault Insertion switch designed for the simulation of fault conditions in automotive/avionics applications, involving the reliability testing of safety critical controllers.
-
Product
8-Channel VME Isolated Resistance Simulator
V420
-
The V420 is an 8-channel, isolated, programmable resistance simulator. It uses entirely solid-state simulation to eliminate transient errors associated with relay switching, and provide for monotonic resistance changes. Channels are individually programmable in four resistance ranges, from 5 ohms to 65.5K. Channels can operate from microvolts up to 35V / 50mA. Overload protection and channel error detection are included.
-
Product
Developer's Studio for ATLAS
PAWS
-
PAWS Developer's Studio gives you the power to compile, modify, debug, document, and simulate the operation of ATLAS test programs in a Windows environment.
-
Product
UV Accelerated Weathering Testers
-
Weice Testing Instrument Co.,Ltd.
UV accelerated weathering testers utilize fluorescent lamp to simulate the UV spectrum of sun shine, combined with temperature control, humidity system.
-
Product
Solar Simulator
-
It is an LED light source for evaluating the performance of organic solar cells in indoor light applications.A neutral white LED light source equivalent to a color temperature of 5000 K, achieving an effective irradiation area of 50 × 50 mm.The illuminance can be changed without changing the height of the light emitting surface with low illuminance (200 lx) and high illuminance (1000 lx).
-
Product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 395kΩ
50-297-142
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI-7851, Virtex-5 LX30 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module
780339-01
Multifunction Reconfigurable I/O
Virtex-5 LX30 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7851 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7851 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
Product
Digital I/O Board
P104-DIO-96
-
Each I/O line of this card is buffered and capable of sourcing 32mA, or sinking 64mA. The board simulates Programmable Peripheral Interface chips (PPI) to provide a computer interface to digital I/O lines. Each PPI supports two 8-bit ports (A, B) and two 4-bit ports (Chi, Clow). Each port can be configured to function as either input or output latches. The I/O line buffers (types 74ABT240 and 74ABT245) are configured automatically by hardware logic for input or output according to the PPI Control Register direction software assignment.
-
Product
Electronic System Design
ESD
-
Smart connected devices are everywhere, in homes, in transportation, and at work. This means electronic system design (ESD) is having a greater influence on almost every type of product requiring new simulation tools to help achieve electronic, electrical, mechanical, thermal, and connectivity goals. Altair’s simulation-driven design tools enable your team of specialized engineers to collaborate across all aspects of printed circuit board development from concept to manufacturing. Our products streamline your process, eliminate design iterations, and reduce time-to-market.
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD | VP 230036
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
Product
Solar Array Simulator DC Module, 65V, 8.5A, 510W
E4361A
Simulator
The Keysight E4361A is a 510W solar array simulator DC power module that simulates the output characteristics of a solar array. The E4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin etc.). The E4360 gives you the flexibility to operate it in two ways:
-
Product
Compressive Strength
-
Compressive Strength testers are used to determine the compressive strength development, gel strength development and elastic moduli of oil well cement under simulated downhole conditions.
-
Product
Bending Drain
-
With the Bending Drain you measure the shrinkage and bending of building materials. Also you may simulate with a built in electrical heating a real world floor heating.
-
Product
Electrician & Technician Testers
-
EVSE's Electrician and Technician testers are created for installation professionals, and are small and durableenough to be carried in a toolbox. These weatherproof handheld units allow new chargers to be checked after installation, verifying a number of vital power and safety requirements, as they simulate the connection a charger makes with an electric vehicle. Simply plug the charger's J1772 connector into the tester's receptacle and you are ready to evaluate operation.
-
Product
PXI High Density Precision Resistor Module, 6-Channel, 4Ω to 1.51MΩ
40-298-050
Programmable Resistor Module
The 40-298-150 is a high density programmable resistor module with 3 channels which can be set between 4Ω and 1.51MΩ with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Transducer Simulator
Model 7V
-
Impedance: 350 ohms nominal. Output Ranges:Fixed rotary switch: 0 to 3 mv/v in 6 steps of .5 mv/v .
-
Product
Four Quadrant Power Amplifier
PAV3000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
PXI Precision Resistor Module 9-Channel, 1 to 239
40-297-113
Programmable Resistor Module
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Programmable Resistor Module
Module
PXI Programmable Resistor Modules are wellsuited for simulating environmental conditions in hardwareintheloop(HIL) validation. The software included provides a simple user interface that accepts inputs in units of temperature or resistance, and configures the resistance across each channel. Each module uses a 37pin DSUB connector on the front panel, as well as a 2x2 MicroFit connector for easy connection to a PXI Digital Multimeter(DMM).
-
Product
Advanced Network Emulators
Netropy
-
Netropy advanced network emulators simulate up to 15 separate WAN links, each with their own bandwidth, delay, and loss characteristics, through each pair of physical ports. Packets can be assigned to individual links by IP address range, VLAN, or any other packet specifier.
-
Product
STANAG3910 Electrica lTest And Simulation Modulefor Standard Ethernet
ANET3910-EN
-
STANAG3910 Electrical Test and Simulation module for Standard Ethernet. The ANET embedded Linux operating system gives the unique capability to run the optional PBA.pro Engine right in the box.Another option is the ANET-ADK onboard software development kit where users create run-time applications to execute right in the box. For wireless applications, an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, 1 KV Isolation
41-752A-101
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture. The 750 V or 1 kV isolation barrier (version dependent) allows the module to be used as a lower power version of a battery stack, representative of those used for vehicle propulsion.
-
Product
FIber Based Solar Simulator
-
Provides up to 12 suns class B non-uniformity over a 12.5 mm diameter with the A4 Light Line and class C uniformity can be achieved over 18mm diameter both with a working distance of 25 cm. Provides up to 4 suns class B non-uniformity over a 12.5 mm diameter with the A1 Light Line with a working distance of 25 cm.
-
Product
Bulk Call Generator and network simulator
Emutel Harmony
-
The Emutel Harmony Bulk Call Generator and network simulator is a highly efficient, cost-effective and flexible tool, invaluable for use in the development, performance verification and pre-deployment testing of many types of VoIP, ISDN and analog equipment.
-
Product
Automation Tool for Mobile App Testing
-
TestingWhiz offers mobile app test automation solutions to help you verify and validate the functioning of mobile apps in a continuous integration workflow. With TestingWhiz, you can automate tests of any native and mobile web apps from the UI level down to the complete back end, as well as perform functional-level testing on real devices and simulators.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
-
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
