-
product
Digital Telemetry Solutions
For measurements on rotating components and moving machinery, imc offers modern telemetry systems for a wide variety of tasks: whether single-channel torque monitoring of a rotating shaft, multi-channel strain gauge and temperature measurements on a train wheel-set or non-contact power measurement on a vehicle drivetrain in harsh environments. There are transmission electronics available for a large variety of sensors, such as strain gauge (quarter-, half- and full-bridge), thermocouples, PT100/1000, as well as IEPE sensors and voltage signals.
-
product
Magnet Wheels Pulse Generators
199SM / 198EM Magnet Wheels
Magnet wheels work with Electro-Sensors Hall Effect shaft speed sensors providing 120 alternating magnetic poles around the circumference of the 3.75" diameter. The 199SM models mount around shafts up to 3" in diameter and are secured with set screws (provided). The 198EM mounts on the end of a shaft with a 10-32 UNF screw (provided - requires center drilling and tapping the shaft).• Use with 906, 906B, 1101 and other Hall Effect, non-metallic-end-capped shaft speed sensors (consult factory)
-
product
Hysteresis Dynamometers
HD Series
16 Standard Models with Maximum Torque from 2.5 ozin to 500 lbin (18 mNm to 56.5 Nm)Hysteresis Braking System: Provides precise torque loading independent of shaft speedMotor Testing from No Load to Locked RotorAccuracy: 0.25% to 0.5% (Full Scale)Air Flow Sensor: For protection against overheating and operator errorStandard Torque Units: English, Metric and SIBase Plate: Available in long or short versionsCustom Dynamometers: for special torque and speed requirementsEasy Calibration
-
product
Gearbox Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
product
Rotary Motion Logger Sensor
NUL-226
This sensor measures angles, rotations, rotation speeds or rotationacceleration. The sensor has a pulley connected to its shaft and the pulley rotation is measured. This sensor has four modes of operation: degrees, rev/s, rad/s, rad/s2.
-
product
Signal Conditioners & Interface
Modbus RTU Remote Connectivity and Control. Minimize Long Cable Runs with Modbus Network. Pulse to Frequency Conversion. Shaft Speed Pulse to DeviceNet. Shaft Speed Pulse to 4-20 mA Conversion.Sensor Compatibility
-
product
Torque Metering System
Measure and record torque for rotating machinery, test stands and ship board applications. Riverhawk Torque Meter Systems are capable of retrofitting to existing couplings and shafts with minimal modification.
-
product
Absolute Encoders
US Digital designs and manufactures absolute encoders in both optical configurations, for the highest possible resolution and accuracy, and magnetic versions for demanding environments. In either case, absolute encoders report a shaft angle within a single 360-degree shaft rotation without stops or gaps. Unlike incremental (sometimes called "relative") encoders, absolute encoders provide true (absolute) shaft position, eliminating the need for a "home" or "zero" cycle after a supply-voltage power cycle.
-
product
Electrostatic Capacitance-Type Gap Detectors
VE series
VE series are non-contact type of vibration/small displacement detector with high accuracy which can measure the distance between conductor such as metal and sensor’s surface in micron/submicron resolution. It demonstrates its best performance when used for the measurement and control of the axial and surface vibration of rotational shafts such as main shaft of turbines, electric motors, compressors, and of the thickness and width of moving objects. In addition to the measurement of the amount of displacement, a gap detector can also be used for a wide range of other measurement and control applications such as the measurement of the amount of slack or warping. The non-contact measurement process enables to apply no load to rotational or vibration body, and does not affect the material under measurement.
-
-
product
Level Float Switch
2285
The 2285 Level Float Switch is suitable for level switching of various liquids, sewage in shafts, tanks, basins or cisterns. The double-chambered float is made of injection molded tough polypropylene that ensures good waterproof protection.
-
product
Air And Gas Probe
GT-1
GT-1 Air and Gas Probe - 24'' #304 stainless steel shaft. Wooden Handle. For instant readings of temperature gradients in environmental chambers, freezer boxes, etc. Diameter is .3/16'' diameter. Immersible. Maximum temperature 200°C, Time constant Seconds. 5 foot lead. Not isolated.
-
product
General Purpose Probe
HT-1
HT-1 ''Workhorse'' General Purpose Probe - designed for temperature measurement of liquids, gases and semi-solids. Plastic handle with straight 3'' stainless shaft. Not good for surface temperatures. Maximum temperature 400°C, Time constant 0.5 Seconds. 5 foot lead. Not isolated.
-
product
Load Measuring Pins
Magtrol Load Measuring Pins are temperature-compensated transducers used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load.
-
product
Wind Speed Sensor/Anemometer
ENVIROMUX-WSS
Rugged anemometer. 3-cup rotor pressed on a stainless steel shaft. Reed switch and magnet providing one pulse per rotation. Rotor diameter: 5 inches. Speed range: ~ 3 mph to 125+ mph (~5 kph to over 200 kph). Rugged Delrin body with bronze and Rulon bushings. Flat aluminum mounting bracket with 2 holes. esigned to be mounted on top of a pole or bracket. 100 feet of exterior grade wire. Maximum cable length: 1000 ft (305m).
-
product
Brushless Resolver Transducer
HRB
Computer Conversions Corporation
Computer Conversions HRB90 has a shaft that meets CAM switch standards with a high shaft load capacity. They provide direct use on overhung loads and are ideal for use with sprockets. They withstand step stool abuse, they're small in size, easy to mount, waterproof & mill duty.
-
product
Contactless Torque Transducers
RS425
These contactless Torque Transducers are not limited by operational speeds, can fit any shaft and capable of measuring torque from 1nm and up to 500knm, providing highly accurate and reliable torque measurement in many applications.
-
product
Resolver Systems and Resolver Sub Systems
TDSM
Computer Conversions Corporation
The TDSM Series are low cost absolute encoders consisting of a size 11 electromagnetic transducer and a 2.6 x 3.1 x .6 conversion module. The outputs available are 12 to 16 bit binary format representing 0 to 359.99 degrees of absolute shaft angle input. The transducer reference supply is also included in the module which is designed for printed circuit mounting. A data transfer and data hold line are provided for simple computer or microprocessor interfacing. These features in addition to the latest digital circuitry techniques, make these encoders the best selection in today's applications where resolutions greater than 10 bits are required with ultra high reliability assured.
-
-
product
Analytical Gear Inspection Machine
KNM 2X / 5X series
Analytical gear inspection machine for workpieces up to Ø 650 mm. Measuring machines for spur and helical gears, rotors, bevel gears, gear tools, shafts etc. Ultimate highly precise measurement of smaller size gears in the lab or on the shop floor - no foundation required.
-
product
Custom Design/OEM Solutions
Datum Electronics can offer custom solutions to solve your torque and shaft power measurement problems.
-
product
Rotary Position Sensors
Using the same technology as our linear range but with a printed rotary coil opposed to the wound linear coil our rotary sensors offer the same high performance as the linear sensor range but with shaft driven rotary or gravity driven tilt measurement. The standard P500/P502 rotary sensors can be manufactured with a measurement range anywhere between 5 and 160. We also manufacture miniature rotary sensors such as the P501 and P505 and the P503 flat PCB style version for customer application fitment. Like our linear sensor range our rotary sensors are also customisable should the standard range not accomodate your application.
-
product
Shaft Alignment
NXA Ultimate
The combination of alignment and geometric routines allows the user to address many of the root causes of outages as part of a complete preventive maintenance program. With a wide range of applications, a screen interface featuring animated 3-D images and a large color touch screen (6.5″) the NXA Ultimate is remarkably user friendly.
-
product
Transmissive Rotary Codewheel
HUBDISK-1
US Digital offers a wide variety of standard hub / disk assemblies (optical encoder disks attached to an aluminum hub) to aid with mounting on a shaft. Encoder disks may also be ordered as a stand alone item (see the Disks page). These rotary encoder disks are made from mylar polyester film. This material allows for a wide temperature range and is virtually unbreakable.
-
product
Wireless Hazard Monitoring
When it comes to hazard monitoring, we know it simply has to work. HazardPRO was designed from the ground up to provide turnkey, reliable, and consistent protection for your most valuable assets—products, facilities, and most importantly, people. Consistent operation is ensured with built-in tools such as self-diagnostics, transmission logging, and redundant radios providing you confidence that your critical processes are being monitored and logged at all times. Wireless nodes utilize temperature (bearing, ambient, and stud), RPM shaft speed, alignment, and vibration sensors. Ambient Sensors ensure bearing and alignment measurements are relative to the surrounding environment.
-
product
Instrumentation Tutor
Unitech Scales And Measurements Pvt. Ltd
This comprises of temperature and speed using different methods. RTD, thermistor and thermocouple are used as sensors with digital temperature indicator to measure temperature. A small water kettle is supplied as a temperature source upto 100°C. Glass bead thermometer is used as standard temperature measurement source to conduct the experiment. Magnetic and photo reflective sensors are used to measure speed. A FHP motor with speed regulator is used as speed source. To the shaft 60 teeth tone wheels are fixed to generate pulses.
-
product
Torque Sensors
In universities and industry, for basic research or quality assurance: Kistler torque sensors guarantee precise definition of the power and friction values of drives, transmissions and pumps. Strain gage technology (DMS) is a powerful solution for measurements on rotating shafts, and also for long-term dynamic and static measurements. Maximum precision, the most rigid structure possible and high temperature stability: thanks to these assets, DMS sensors can accomplish the most demanding tasks. Piezoelectric reaction torque sensors offer convincing features such as exceptional overload protection, high signal resolution and a wide frequency range. They are ideal for measurement tasks when conditions are difficult due to geometry, temperature range or dynamics.
-
product
High Temperature Magnetic Speed Sensors
SPECTEC Innovative Sensor Solutions
High temperature speed sensors (up to 454° C) are sensitive, shock resistant & reliable for high temp applications in harsh environments, such as race car engines and transmissions. SPECTEC's high temperature magnetic speed pickups are used as transmission sensors, engine governors, output shaft sensors and flow meter sensors. SPECTEC's high temperature magnetic pick-ups are standard in 5/8-18, 11/16-24 and 3/4-20, and M18 shell sizes.
-
product
Shaft Speed Sensors
Electro-Sensors offers many shaft speed sensors for virtually any environment. Our Hall-Effect and Magnetoresistive Sensors sense magnetic targets and work with our magnetic pulsers (Discs, Wraps, and Wheels). Our proximity sensors sense ferrous metal targets, including bolt-heads, screws, gearteeth and keyslots. Our speed sensors monitor shaft speed of equipment and output data as PNP, NPN, or 4-20 mA signals. The sensor data can be used by facilities to monitor machinery and safeguard equipment. Monitoring shaft speed is a fundamental aspect of hazard monitoring and should be utilized by any facility with rotating shafts.
-
product
Hour Meters
Global Digital Instruments, LLC
GDI manufactures hour meters with multiple inputs and mounting styles making them suitable for a broad range of applications. Hour meter options include: Inductive input, AC/DC input, Vibration Activated and Rotating Shaft Tachometer and hour meter.Hour meters are used within a variety of industries where equipment is regularly used. They are useful for determining when regular maintenance is needed to help extend the life of the machine.
