PXI Interfaces
-
Product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
13 GHz Differential Probe with ProLink Interface
DH13-PL
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Interface Card
XMC-WMUX
-
Alta Data Technologies’ XMC-WMUX interface module (PCI Express Mezzanine Card for Carriers and Single Board Computers or Carriers) is a single or dual-channel (A-B Redundant = 4 Busses per Channel/Wings) WMUX card supported by the latest software technologies.
-
Product
Multiprotocol PCI/104-Express Interface Board
8000PCIe104
-
The EXC-8000PCIe104 is a multiprotocol PCI/104-Express interface board for embedded applications or avionics test and simulation applications. Each board holds up to four independent modules and 10 discrete channels.
-
Product
Interface Units
-
intelligent, microprocessor controlled, data acquisition and lambda measurement unit for up to 6 wide band UEGO sensors. It is based on the sensor node and can be used as part of the DATA
-
Product
Compact IEPE Sensor Interface
Plug.n.DAQ Lite
-
ROGA Instruments Plug.n.DAQ Lite is a compact IEPE sensor interface for linux or windows with 2 input channels. It offers the USB PC interface and requires no drivers for installation. The operating system such as LINUX or Windows recognizes the device as an external usb audio card.
-
Product
Professional Technician Interface
d-briDGe Pro
-
The d-briDGe PRO is DG Technologies’ newest product and is used in conjunction with software applications to provide reprogramming and diagnostics to essentially all J2534 compliant domestic, Asian and European vehicles.
-
Product
Interface Converters
-
Electro Standards Laboratories
Supporting a variety of medias, applications, and entities such as Casino/Lottery VLT Networks, Industrial Process Control, Government Laboratories, etc.
-
Product
68 Pin Breakout Interface
VSI-Breakout-68
-
The VSI-Breakout-68 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Single Port RS-232 Interface
PCI-COM232
-
Serial ports: 1Configured: Address and interrupt configured through PCI BIOS and supplied driversMax. baud rate: to 460.8 Kbps, software selectable per channel for 115.2, 230.4, or 460.8KbpsSerial modes: 5, 6, 7, or 8 data bits; odd, even or no parity; 0, 1 or 2 stop bitsUART: 16C550 standardInterrupt Status: Each UART interrupt status read from any UARTís Scratchpad RegisterConnector: 37 position D-type with cable to DB-9 (DB-25 optional)Power: +5V only
-
Product
Filtered DC Interface Module
-
DC modules for RF Test Enclosures eliminate conducted and radiated interference, while providing a source of DC power.
-
Product
Serial to Relay Interface Boards
Model 2364 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Serial interface header includes RS-232 and RS-485 signals. * GPIB interface header includes GPIB address switch input signals.* Includes 50-pin mating relay connector and serial header connector.* Optional 115750 Terminal Board for easy connections without soldering.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel.
-
-
Product
Aerospace Interfaces
-
Aerospace InterfacesDecode and visualize data from ARINC 429, MIL-STD-1553, IRIG CHAPTER 10, iNET and IRIG Chapter 4 PCM telemetry data interfaces.
-
Product
GSP-2B Test System Interface Probe
GSP-2B
-
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 125Full Travel (mm): 3.18Recommended Travel (mil): 125Recommended Travel (mm): 3.18Overall Length (mil): 845Overall Length (mm): 21.46
-
Product
PCIe-8431, PCI Express, 8-Port, RS485/RS422 Serial Interface Device
780592-01
-
The PCIe‑8431/8 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between … 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Hall Sensor Board with I2C Interface
050-279
-
Version: +5V/90A +3,3V/25A +12V/60A +12V/60A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Hall Sensor Board with I2C Interface
056-742
-
Version: +5V/60A +3,3V/60A +12V/90A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
-
Product
37 Pin Breakout Interface
VSI-Breakout-37
-
The VSI-Breakout-37 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
25 Pin Breakout Interface
VSI-Breakout-25
-
The VSI-Breakout-25 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
GPIB ANSI X3.28 Interface
Model 4894B-7
-
ICS's GPIB to ANSI X3.28 Interfaces adapt older devices that use the ANSI X3.28 devices to the GPIB Bus. All ICS GPIB Interfaces are IEEE-488.2 compliant and HP-IB compatible.
-
Product
PMC Compatible Bi-Directional Serial Data Interface
PMC-BiSerial III
-
The PMC BiSerial family has been updated to include a Spartan III [Xilinx] based card with expanded capabilities.. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-III. The BiSerial III features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
Product
Front Panel Interfacing Kit: M9018A And M9019A
Y1270A
-
The Y1270A Front Panel Interfacing Kit for M9018A and M9019A PXIe chassis provides a rugged interface to the front panel connectors of modules installed in the chassis. The frame is provided with a semi-transparent cover which provides additional protection for front panel cables and connectors.
-
Product
SIP-90-4 Test System Interface Probe
SIP-90-4
-
Overall Length (mil): 693Overall Length (mm): 17.60Rec. Mounting Hole Size (mil): 57Rec. Mounting Hole Size (mm): 1.45Recommended Drill Size: 1,45 mm
-
-
Product
PXI-8368, MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module
783934-01
-
MXI-Express Interface with Connector for Fiber Cable, PXI Remote Control Module—The PXI‑8368 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8366 through a copper, x1 MXI‑Express cable. The fiber-optic cabling of the PXI‑8368 provides electrical isolation between the PC and PXI chassis, as well as cabling up to 200 m per link.
-
Product
Ethernet Multi-Function Interface
2426
-
Controls/monitors real world signals over Ethernet 24 digital I/O, 6 analog in, analog out, serial comm, incremental encoder in PWM and debounce on digital I/Os Integral support for safety interlocks Embedded HTTP and Telnet servers Open source API Low cost, low power & compact size
-
Product
PXI Hardware
-
PXI is now the primary format for ATE Self Integrators. Terotest offer a complete range of PXI equipment that is designed to work together and has full software support for all its PXI modules and drivers.
-
Product
ARINC 429 Test & Simulation Interface for VME
VME-429
-
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
