Interface Devices
soft and hard handshake between devices.
-
product
Electricity Metering Device- Residential
Mk32H
Designed for residential use, Mk32H is a DIN Rail single phase meter with integrated 100A UC3 compliant relay. It is able to operate in either STS compliant prepaid mode or post-paid mode.Mk32H can operate with the EDMI CIU (Customer Interface Unit) – HD18 wirelessly as a split meter as well as operate with EDMI gateway – GW30 and the EDMI Head End System – MultiDrive as a complete AMI system.
-
product
Timing Devices (Crystal Unit / Ceramic Resonator)
Timing devices are passive component which creates clock signal by the piezoelectric effect. This device is used for various applications, including for mobile phones, wearable devices and AV/PC.
-
product
Ethernet Digital Interface
Model 8063
* Provides 48 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes or data strings.* Transparent data transfer mode.* Fully VXI-11 Compliant plus Raw Socket for easy programming with Visual Basic or C, Agilent VEE and LabVIEW.* 1 U high rack mount kit mounts one or two 8063s.* Includes 100-230 VAC Power Adapter with universal plugs.
-
product
RS-232 to RS-485 Optically Isolated Interface Converter
Model 8322
FEATURES: 4 Wire-Master/Slave Operation; Active Mode Control Via RTS or Data; Opto Isolation; Built-in Power Supply; Internal Microcontroller; 38.4 KBPS Data Rate; DIN Rail Mountable; Programmable Terminations. The Model 8322 RS-232 to RS-485 Interface Converter allows information exchange in half duplex mode over two twisted pairs.
-
product
Automated Hipot Accessory Device
CX-K12
Shenzhen Chuangxin Instruments Co., Ltd.
Purpose, To test thin insulating materials for dielectric voltage withstand strength when connected to a hipot tester.
-
product
Digital Backplane Interface Board
MSXB 033
The Microstar Laboratories Digital Backplane Interface Board, part number MSXB 033, interfaces the Digital Backplane with a Data Acquisition Processor. The Digital Backplane Interface Board must be installed in the Digital Backplane to connect the backplane to a Data Acquisition Processor.
-
product
Power Interface Board 3U, 1PSU connector
106PIBM301-0000R
The PIB 3U 1 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
Partial Discharge Simulation Devices
Hangzhou Xihu Electronic Institute
Simulation device of cable PD faults, simulation device of switchgear PD faults, simulation device of GIS PD faults, simulation device of transformer PD faults.
-
product
Electricity Metering Device
Mk7C
Built on the advanced Atlas metering platform, the Mk7C is a single meter with an integrated 100A UC3 compliant relay which allows disconnection and reconnection of electrical services remotely.
-
product
Digital Reconfigurable I/O Device
The Digital Reconfigurable I/O (RIO) Device features user-programmable FPGA for onboard processing and flexible I/O operation. You have complete control over the synchronization and timing of all signals and operations along with custom onboard decision-making that executes with hardware-timed speed and reliability. You can configure user-defined hardware for a wide variety of applications, such as custom digital DAQ, high-speed waveform generation, sensor simulation, hardware-in-the-loop (HIL) test, custom digital communications protocols, bit error rate testing, and other applications that require precise timing and control.
-
product
Automated Wafer Prober for Magnetic Devices and Sensors
Hprobe design and fabricate turnkey automated testing equipment (ATE) for electrical characterization and testing of integrated circuits under magnetic field such as MRAM (Magnetic Random Access Memory) and sensors. In each phase of the technology and product development as well as during mass manufacturing, a dedicated magnetic tester is available.
-
product
Measuring Device Equipment
Energie Check profi
Diverse building diagnostics and interior climate control options are possible with the measuring device case. The ideal measuring device equipment for building diagnostics and checking the indoor temperature: for energy advisers, caretakers, engineering companies and environmental officers. Tests can also be made regarding water consumption, illumination and energy consumption of electrical devices.
-
product
PXIe-6593, 16 Gbps, 8-Channel PXI High-Speed Serial Instrument
785976-01
PXIe, 16 Gbps, 8-Channel PXI High-Speed Serial Instrument - The PXIe‑6593 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex Ultrascale FPGA to implement various high-speed serial protocols, and it is … programmable in LabVIEW FPGA for maximum application-specific customization and reuse. The PXIe‑6593 takes advantage of FPGA multigigabit transceivers for up to eight TX and RX lanes.
-
product
GPIB-RS232, Instrument Control Device
779732-10
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Device Measurement EXpert (DMX)
S94601B
Device Measurement eXpert (DMX) is a measurement configuration assistant that aides users in setting up and optimizing complex measurements for various types of devices. The customizable wizard guides users through DUT connection, measurement setup, and display. DMX provides repeatability across the workflow by automatically setting up measurements in a consistent and optimal manner.
-
product
Fibre Channel XMC Interface Module
XMC-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Supports DMA for high speed streaming of data to/from the board - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
VXI Register Interface Board
VXI-5524A-3
* 3.3V power out instead of 5 V on Digital IO bus connector* All othe specifications same as listed above for the VXI-5524A board.
-
product
Pressure Transducers with Serial(485) Interface
P855
The Validyne model P855 is a digitally compensated differential pressure transmitter designed for industrial pressure measurement applications. The on-board microprocessor provides high accuracy and improved stability in changing thermal environments.
-
product
Portable Radioisotope Identification Devices (RIIDs)
ORTEC Detective Family Hand-Held Radioisotope Identifiers (HHRIIDS or RIIDS) have been in the front line of operations to interdict the illicit trafficking of nuclear materials worldwide, ORTEC RIIDS are used every day.
-
product
Power Interface Board 3 HE, 2PSU-Steckverbinder
106PIBM302-0000R
The PIB 3U 2 slot has two power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
Electrical Interface
QSFP-DD 200G
Eoptolink Technology Inc., Ltd.
QSFP-DD 200G Eoptolink’s EOLD-162HG-E-10-1 QSFP-DD CWDM4, 8x25G Optical transceiver module are designed for use in 200 Gigabit links over 10km singlemode fiber. They are compliant with the QSFP-DD MSA. Digital diagnostics functions are available via the I2C interface, as specified by the QSFP-DD MSA.
-
product
Professional Technician Interface
d-briDGe Pro
The d-briDGe PRO is DG Technologies’ newest product and is used in conjunction with software applications to provide reprogramming and diagnostics to essentially all J2534 compliant domestic, Asian and European vehicles.
-
product
Mobile Drone-detection Device
RadarZero
Compact drone detection radar product. At roughly the size of a paperback book, the product can detect drones up to 750m away and sells for a fraction of the cost of the larger longer-range more conventional radars.
-
product
PCI-5421, 100 MS/s, 16-Bit Waveform Generator Device
778692-03
The PCI‑5421 can generate user-defined, arbitrary waveforms and standard functions, including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -6 V to +6 V and uses direct digital synthesis (DDS) to precisely generate waveforms. The PCI‑5421 also features advanced synchronization and data streaming capabilities.
-
product
CAMAC Controller With USB Interface
CC-USB
The CCUSB is a full-featured CAMAC Crate controller with integrated high speed USB-2 interface and full CAMAC dataway display. It supports Master and Slave operations with complete CAMAC arbitration as well as auxiliary CAMAC controller operation.
-
product
PCI-5421, 100 MS/s, 16-Bit Waveform Generator Device
778692-01
The PCI‑5421 can generate user-defined, arbitrary waveforms and standard functions, including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -6 V to +6 V and uses direct digital synthesis (DDS) to precisely generate waveforms. The PCI‑5421 also features advanced synchronization and data streaming capabilities.
-
product
Tactile Measuring Devices
You want precise results easily, quickly and flexibly? We have the right tool for you with our tactile measuring devices. Benefit from the broadest probe portfolio on the market and get efficient software solutions for data transmission, data evaluation and data export with the Tactile Suite® and the Fischer DataCenter. Whether coating thickness measurement or materials testing: Discover the right solution for your application and your industry.
-
product
Interfaces
A broad product portfolio of interface technologies that offer lower power consumption, reduced size and ensure the highest performance signal transfer.
-
product
GPIB to LAN Printer Interface
Model 4872
* Adds a GPIB Interface to Ethernet Printers. * Replaces obsolete printers and plotters with a current HPGL/PCL5 printer.* Secondary output copies instrument print file to a PC for later printing with our Data Logger program.* Automatically finds and links to most printers.* Built-in test page confirms 4872 to printer operation.* No program changes required.* Rack mountable in 1 U high rack mount kit.* Includes universal VAC Power Adapter and LAN crossover cable.
-
product
Measuring Devices For Drawing Rings And Dies For 2-piece Can Production
OEM GmbH supplies Ringmaster No. 100 to Wallram Group
Optik Elektronik Gerätetechnik GmbH
In 2021, OEG GmbH celebrates its 30th anniversary and the delivery of the 100th Ringmaster to the Wallram Group. Read an interesting report about this.
