Wave
undulation up-down synced with to and fro. Scope of site
See Also: Long-Wave IR, Lightwave, Shear Wave, Sub-mm Wave, Microwave, Wavelet, Continuous Wave, Submillimeter Wave, Sine Wave, Millimeter Wave, Shock wave, Ocean, Quantum, Gravity, Particle, Seismic
-
product
RMS to DC Converters
RMS-to-DC converters manufactured by Analog Devices are used in a wide variety of applications where precision and low power measurement of ac signals is the prime objective. An ADI rms-to-dc converter offers real time measurements, meaning there are no latency issues such as those that limit the frequency response of other technologies—the dc output is simply the equivalent of the rms input, over a wide range of input frequencies, and for complex waveforms not limited to sine waves. ADI offers a wide range of rms-to-dc converters optimized for the most demanding performance, power, and cost applications satisfying true rms needs.
-
product
Closed Loop Hall Effect Current Sensors/Transducerswith Rectangle Windows
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used formeasurement of DC and AC current, pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
product
sbRIO-9222, Non-Enclosed, ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
785479-01
Non-Enclosed, ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The sbRIO‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the sbRIO‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
BNC Twinax Connectors
BNC Twinax connector category has several part numbers, the majority are RoHS and REACH compliant. BNC Twinax connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our BNC Twinax connectors are built to precise industry specifications. Pasternack BNC twinax connector items are available in jack or plug gender with 78 Ohm impedance. Connectors in twinaxial BNC are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These BNC Twinaxial connector designs include clamp/solder, crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this twinax BNC connector series is in-stock. In addition to being in stock, these twinaxial BNC connectors will ship the same day as they are purchased.
-
product
Gateway
CODA-4589
Hitron Americas Technologies Inc.
The CODA-4589 has the capability to receive 5Gbps based on 2 x OFDM + 32 QAM over its DOCSIS 3.1 interface.The integrated Wi-Fi 3×3 2.4 GHz 802.11n and 4×4 5 GHz 802.11ac Wave 2 dual band MU-MIMO Access Point significantly improves customer experience extending range and coverage with blazing speeds. For wired clients, the four Gigabit Ethernet ports offer ultra-fast connections. MoCA 2.0 bonding provides a near-Gigabit wired backbone in the customer’s home for Wi-Fi extension.
-
product
1.85mm Connectors
Pasternack 1.85mm connector (also known as a V connector) category contains many part numbers, the majority are RoHS and REACH compliant. 1.85mm connector series in this category will terminate to coax. Pasternack 1.85mm connectors are built to precise RF and microwave industry specifications. Pasternack 1.85mm connectors are built in male or female gender with 50 Ohm impedance. 1.85 mm connector series is available in threaded, 2 hole panel or mountless options. These connectors with 1.85mm designs include clamp/solder or field replaceable attachment methods. As with the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 1.85mm connector series is in-stock. In addition to being in stock, these 1.85 mm connectors ship the same day as they are purchased.
-
product
NI-9223, ±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781398-01
±10 V, 1 MS/s, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9223 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9223 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9223: either four, 2‑position screw terminal connectors or four BNC connectors.
-
product
WR5.1 Frequency Extension Solution, 140-220 GHz with VDI Extender Modules
CobaltFx 140 to 220 GHz
CobaltFx cost-effective millimeter wave frequency extension system allows you to build a scalable and affordable 5G testing solution.
-
product
Pressure Sensor Kit for Changing Ranges
DP15TL
The wide range of diaphragms furnished eliminates expensive stocking of several transducers and offers the versatility of the differential type bi-directional transducer at a very low cost. The broad line pressure capability of this unit makes it useful in almost every laboratory application from flow to level measurement, vacuum to 3000 PSIG. The high output, when used with a carrier system such as the Model CD15 Sine Wave Carrier Demodulator or the CD12 Transducer Indicator, provides resolution equal to many secondary standard units.
-
product
Millimeter-wave Operation With Frequency Extenders For M980xA PXI VNA
S95560B
banded vector network analyzer (VNA) using the M980xA PXI VNAs and N5252AW or N5262BW Frequency Extenders.
-
product
Fixed Wavelength CW Laser Source (DFB)
Laser 1200 Series
The Laser 1200 Series is a highly customizable fixed-wavelength Continuous Wave (CW) laser source available in a wide range of wavelengths and powers.With seamless PXI integration, it can be easily integrated into new or existing PXI test setups. Save space, lower your costs and improve testing efficiency while delivering reliable and repeatable results in production or research environments.
-
product
Quantum Gravimeter
The quantum gravimeter, the first commercial device of its kind in the UK, uses quantum interference of matter waves to measure the local value of gravitational acceleration, or ‘g’, with very high precision. Objects with different mass cause small fluctuations in the value of g measured on the surface of the Earth. The quantum gravimeter can be used to sense these objects hidden under the surface in a non-intrusive manner.
-
product
Analog Phase Shifter
Analog Devices analog phase shifters change the phase of RF, microwave, and millimeter wave signals. Our technology features consistent insertion loss vs. phase shift, monotonic phase shift, low insertion loss, and a compact size that makes it ideal for multiple applications, including:• Fiber optics• Military• Test equipment
-
product
Thickness Meter
Shenzhen Graigar Technology Co.,Ltd.
An ultrasonic thickness gauge is a measuring instrument for the non-destructive investigation of a material's thickness using ultrasonic waves.
-
product
Octal 4 to 1 50 600MHz PXI RF Multiplexer
40-760-008
This octal 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
product
Tunable CW Laser Source
IQTLS
The IQTLS is a continuous wave (CW) laser source combining high-power output, narrow 100kHz linewidth and 0.01pm resolution tunability. Available in single or dual laser configurations, this tunable laser source can be controlled locally via USB or Ethernet ports and is SCPI VXI-11 compliant.
-
product
RF Proximity Detector
Type RPD-2 AND Type RPD-2A
The Type RPD-2 Radio Frequency (RF) Proximity Detector is designed to detect and locate devices that radiate radio waves in the high frequency to low microwave frequency range. Such devices often include surveillance and “spy” equipment. The Type RPD-2, when used with the different sensors, will detect the emanation of the radio wave within a confined area, and then isolate its location to within approximately a square foot. The type RPD-2A may be used as an RF field strength indicator for antenna field strength measurements. The RPD-2A is identical in function except that the meter scale is calibrated in relative dB units.
-
product
Millimeter Wave Antenna Testing
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
product
Level Sensors
*High reliability due to the elimination of mechanical components*Different function principles: Guided wave radar, capacitive and hydrostatic*Devices for limit level detection or continuous level measurement*Clearly visible LED display*Suitable for all common industrial and process fluids
-
product
NI-9222 , ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
783283-01
±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
Carriers For Various Machining Processes
MG Products has multiple types of solder carriers. Two major types are those for selective soldering and those for wave soldering. Our wave soldering carriers are tailor-made and designed by our experienced engineers. These carriers make it possible to solder THT components on complex arrangements, even with bottom-mounted components.
-
product
Electrodynamic Vibration Generator System
LVD-100KG
• Vibration table size: 500*500mm (Other size can be designed) • Vibration: 0~5mm (Adjustable range P-P). Vibration waveform: sine wave (half wave and full wave). Acceleration speed: 0~20g (Adjustable) • Maximum test load Capacity: 100kg • Accuracy: Frequency can be displayed to 0.01 Hz. Precision 0.1 Hz. • Sweep Frequency function (1~600Hz): (Upper frequency, Lower frequency, Time range) It can set real standard arbitrarily to sweep frequency back and forth • Programmable Function (1~600Hz): It can set each segment in 15 segments arbitrarily (frequency/amplitude/time/acceleration), and it can be recycled • Frequency doubling function (1~600Hz): 15 segments multiplied-increase: 1)Low to high frequency 2)High to low frequency 3)Low to high and then to low frequency, it can be recycled • Logarithmic function (1~600Hz), 3 modes of logarithm/can be recycled: 1)Lower to upper frequency 2)Upper to lower frequency 3)Lower to upper and then to lower frequency • Measuring instrument: To display amplitude, acceleration speed and the maximum acceleration speed.
-
product
Integrated Modular Electromagnetic Modeling Suite
EM.Cube
EM.Cube® is an industry-recognized simulation suite for electromagnetic modeling of RF system engineering problems. It features several distinct simulation engines that can solve a wide range of modeling problems such as electromagnetic radiation, scattering, wave propagation in various media, coupling, interference, signal integrity, field interactions with biological systems, etc. Using EM.Cube, you can solve problems of different sizes and length scales, varying from a few microns in MEMS devices to several miles in large urban propagation scenes.
-
product
75 Ohm 1.6/5.6 Connectors
Pasternack 75 Ohm 1.6/5.6 connector category includes many part numbers, the majority are RoHS and REACH compliant. 75 Ohm 1.6/5.6 connector series in this category will terminate to coax or PCB (printed circuit board). Our 75 Ohm 1.6-5.6 connectors are built to precise industry specifications. 75 Ohm 1.6-5.6 connectors are constructed in jack or plug gender with 75 Ohm impedance. 75 Ohm 1.6/5.6 connectors are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm 1.6-5.6 connector designs include clamp/solder, crimp/solder or solder attachment methods. Like the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 75 Ohm 1.6/5.6 connector series is in-stock. Not only are these 1.6 / 5.6 connectors in stock, but they also will ship the same day as they are purchased.
-
product
Portable Reference Generator - 5VA
RG-5
Programmable Frequency & Voltage Portable Sine Wave Generator Sunlight Readlable Display Transformer Isolated Output 360 - 11000 Hz with 1Hz Resolution 1.9V to 125V Output with AGC
-
product
QMA Connectors
Pasternack QMA connector category contains dozens of part numbers, most of which are RoHS and REACH compliant. QMA connector series in this category will terminate to coax or PCB (printed circuit board). Our QMA connectors are built to precise microwave and RF industry specifications. QMA connector products are manufactured in male or female gender with 50 Ohm impedance. Connectors in the QMA category are available in straight or right angle versions, as well as, bulkhead or mountless options. These QMA connector designs include crimp/solder, solder or solder/solder attachment methods. As with our other over 40,000 RF, microwave and millimeter wave products from Pasternack, this QMA connector series is in-stock. Not only in stock, but these connectors will ship the same day as they are purchased.
-
product
Single 32 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-767-001
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
product
Single Photon Detector System For Near-Infrared (1.3-1.6 Um Wavelength) Waves With Closed-Cyle Cooling
Insight Product Company is proud to offer Single Photon Detector System for Near-Infrared (1.3-1.6 um wavelength) waves with Closed-Cylce (cryogen-free)cooling .
-
product
Shortwave Power Amplifier
OM4001A
The OM Power model OM4001A is designed for all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands) and all modes. It is equipped with a two ceramic tetrodes FU-728F.
-
product
Highpass Filters
Frequency range of this band pass filter is 1,000 MHz to 2.5 GHz and the passband is 1.5 GHz. PE8715 highpass filter is one of over 40,000 RF microwave and millimeter wave components supplied by Pasternack. Our 5 section highpass filter can be bought and shipped worldwide the same-day as with our other in-stock RF parts.
