-
Product
PXIe-4145, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit
782435-01
Source Measure Unit
PXIe, 4-Channel, ±6 V, 500 mA Precision PXI Source Measure Unit - The PXIe-4145 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote (4 wire) sensing for accurate measurements. The fast sample rate of the PXIe-4145 can reduce measurement times, capture transient device characteristics, and allow quick I V characterization of devices under test (DUTs). With a high-speed sequencing engine, you can synchronize all these SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4145 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
PXIe 5-channel Source/Measure Unit, 500 kSa/s, 100 pA, 30 V, 500 mA
M9614A
Source Measure Unit
The Keysight M9614A is a PXIe five-channel source / measure unit (SMU). It supports accurate measurement up to 30 V / 500 mA with resolution down to 6 μV / 100 pA.
-
Product
Light Source
UVF-352S
-
This is the ultra high power unit fully utilizing the high stability and long life 350watt ultra high pressure mercury lamp. The unit is made to compact size.
-
Product
sbRIO-9215, Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781029-01
Voltage Input Module
Non-Enclosed, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The sbRIO‑9215 performs differential analog input. The sbRIO‑9215 contains NIST‑traceable calibration, a channel‑to‑earth ground double isolation barrier for safety and noise immunity, and high common-mode voltage range. Non-enclosed modules are designed for OEM applications.
-
Product
Noise Sources
-
The Keysight 346, 347 and SNS Series of noise sources work in conjunction with the NFA Series noise-figure analyzers to make noise-figure measurements from 10 MHz to 50 GHz.
-
Product
Light Sources
LS 150 Xenon Arc Lamp Source
-
Model LS-150 is a Patented US Pat. No. 8116017 low cost, high output 150 watt Xe arc lamp based light source. The entire source, power supply, lamp, and optical compartment are housed in an extremely compact enclosure, 9 x 6 x 11 inches. The unit's base allows mounting on inch or metric spaced optical tables with the optics centered over the hole pattern to allow for easy integration with the rest of your setup.
-
Product
Laser Source
TW3110
-
Techwin(China) Industry Co., Ltd
Laser Source TW3110 is the most rugged small size instrument in the industry. It integrates super small size and strong function in one unit. With 3 pieces of 1.5V alkaline batteries, it can work continuously for more than 40 hours. The total weight is only 110g. Together with the TW3205 Mini optical power meter, it provides an excellent solution for fiber optic network and for field work.
-
Product
Point Source
KF Series
-
All loudspeaker systems in the KF Series feature three-way design. Each sub-series applies three-way design to meet a particular set of requirements.
-
Product
Power Sources
-
EPOS 340 is the multi-functional three-phase generator which comes into its own whenever maximum power and high signal accuracy are required.Intelligent amplifier technology and fully synthetic signal generation make it possible to issue any signal shape across a wide frequency range or even to play back complex transient signal characteristics. EPOS 340 is designed for use as a stand-alone device or for operation with an external PC.
-
Product
sbRIO-9201, Non-Enclosed, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
781114-01
Voltage Input Module
Non-Enclosed, ±10 V, 500 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The sbRIO‑9201 is an effective combination of channel count and speed at a low price for an economical multifunction system. In addition to the absolute protection from the isolation, the module features up to 100 V of overvoltage protection for errant signal connection or unexpected outputs to the individual channels. Non-enclosed modules are designed for OEM applications.
-
Product
Light Source
UVF-502S
-
In combination use with the uniform exposure unit, selection of uniform irradiation area in the range of 80mm200mm is possible.
-
Product
Light Source
LS-HA
-
provides the stable and smooth wide-band spectral output. It’s proper for most visible to near infrared range measurement. This light source is also designed to be used in the standard measurement package. It ‘s a simple and quick measurement platform.
-
Product
Source Phase Control
S95088B
-
The S95088B allows users to set calibrated, arbitrary phase differences between two signal sources on the M980xA PXI VNAs.
-
Product
Short Light Source
LM-AS
-
The short light source is compatible with the LM-101 or the LMC-20. The light is supplied with a 50 watt tungsten halogen convection cooled light source which provides suffcient energy for use with narrow band pass filters or monochronomators in the wave length range of .35 to 2.5 microns. The light beam is chopped at 200 hz by a quiet, vibration free, synchronous motor. The housing also contains a secondary LED light source and detector for synchronization of the amplifier, plus an electro-mechanical shutter to block the light output when the instrument is zeroed. An internal collimating lens produces a narrow beam (<1") so the LM-AS can be used in bell-jar and large coating systems.
-
Product
Calibration Light Source
CAL2
-
Image Engineering GmbH & Co. KG
The CAL2, based on our 22 channel spectrally tunable iQ-LED source, can be adapted for use in many different areas.
-
Product
AC Power Sources
-
Test basic AC power with confidence using the most stable, reliable AC power sources More effectively simulate and analyze high-performance AC environments with built-in measurement capabilities Lower your cost of ownership with global support and the longest standard warranty in the industry
-
Product
Programmable AC Source
6500
-
Chroma Systems Solutions, Inc.
1200VA ~ 9KVADirect Digital Synthesis (DDS) waveform generationProgrammable voltage, current limit, frequency, phase, and distortion
-
Product
Reference Sources
-
A physical or digital document that you would refer to for more information about a topic.
-
Product
AC Power Sources
CSW Series
-
AMETEK Programmable Power, Inc.
The CSW Series represents a new generation of AC/DC power sources that address the increasing demands on test equipment to perform additional functions at a lower cost. By combining a flexible AC/DC power source with a high performance power analyzer, the Compact CSW Series is capable of handling complex applications that have traditionally required multiple systems. The sleek integrated approach of the CSW avoids cable clutter that is commonly found in test systems. All connections are made internally and the need for digital multimeters, power harmonics analyzers, and current shunts or clamps is eliminated.
-
Product
Clean Power Source
AC1000A
-
The AC1000 achieves its unique price/performance ratio by actively adjusting the incoming mains waveform to produce a clean output. Other suppliers use convertor techniques to completely recreate the output from scratch. Our solution delivers an output which achieves the required THD with the minimum of hardware and expense. It includes the ability to switch the correction in or out so that the original waveform can be observed and measured if required. Overload and thermal protection systems are built-in and produce an audible warning if activated.
-
Product
Voltage Meter
МН32С
-
The mezzanine module (mezzanine) МН32С is designed to measure instantaneous voltage values over thirty-two differential channels.
-
Product
AC Power Source
6500 series
-
The global AC power testing requirements demand more sophisticated AC Power Source that is capable of simulating a wide variety of AC line conditions, harmonic waveforms, accurate power measurement and analysis. The Chroma 6500 series Programmable AC Power Source delivers the right solution to simulate all kinds of normal/abnormal input conditions and measure the critical characteristics of the product under test. It can be used for R&D design characterization, production testing, and QA verification of commercial, industrial, and aerospace electronic products. The Chroma 6500 series delivers maximum rated power for any output voltage up to 300 Vac, and at any frequency between 15Hz to 2000Hz. It is suitable for commercial applications (47-63Hz); for avionics,marine, military applications at 400Hz or higher frequency; or for electrical motor, air-conditioner test applications at 20Hz. All models generate very clean sine or square waveforms output with typical distortion less than 0.5%. The Chroma 6500 series has built-in Direct Digital Synthesis (DDS) Waveform Generator to provide user programmable high precision waveform. For testing products under AC line distortion conditions, clipped sinewave can be generated with 0% to 43% distortion and amplitude from 0% to 100%. It also can simulate all kinds of power line disturbances such as cycle dropout, transient spike, brown out, phase angle, voltage and frequency ramp up (ramp down), etc.. Up to 30 harmonic waveforms are factory installed, and testing for compliance to AC line harmonic immunity standards can be easily achieved in the field.
-
Product
High Voltage
-
Accurate measurement of high voltages acc. to VDE 0432 und IEC 60060 in conjunction with a high voltage divider.For the measurement, the principle of capacitive or resistive divider is used, which can be selected in the peak voltage meter.
-
Product
UV Exposure Sources
-
Standard maintenance, lamp, or filter replacement, does not require any tools. Locking indicator dials on all the system controls, located together for ease of alignment, provide for a reproducible setup. A beam imaging accessory makes alignment even faster.
-
Product
4- Channel PXI Source Measure Unit (SMU)
GX3104
Source Measure Unit
The GX3104 is a precision 3U PXI module that forces and senses both voltage and current over a range of ±20 V and up to ± 1 A ( channel 1) with channels 2- 4 capable of supplying up to 500 mA. Total available output current from the module is 1A. The four channels are electrically isolated from the PXI power supply and share a common, isolated ground.
-
Product
Voltage Testers
-
Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece
-
Product
Long Light Source
LM-A
-
The long light source is compatible with the LM-101 or the LMC-20. The light is supplied with a 50 watt tungsten halogen convection cooled light source which provides suffcient energy for use with narrow band pass filters or monochronomators in the wave length range of .35 to 2.5 microns. The light beam is chopped at 200 hz by a quiet, vibration free, synchronous motor. The housing also contains a secondary LED light source and detector for synchronization of the amplifier, plus an electro-mechanical shutter to block the light output when the instrument is zeroed. An internal collimating lens produces a narrow beam (<1") so the LM-A can be used in bell-jar and large coating systems.
-
Product
Surface-Mount Noise Sources
-
Mercury’s family of surface-mount noise sources provides exceptional performance in a compact and easy to integrate package. These products are ideal for applications such built-in test and dithering circuits where the system requirements drive a need for compact, surface mount technology.
-
Product
Laser Source
-
Is an Amplified Spontaneous Emission (ASE) based broadband light source, designed for general laboratory applications. It is a reliable and cost-effective unit that can be ordered with multi channel options. The LD operating temperature and drive current are precisely monitored by a micro-controller to ensure constant output power and emission wavelength stability. With compact size configuration, it’s also suitable for OEM integration, User can control the ASE source output power level by adjusting the drive current along with remote status monitoring, contact Optilab for more information.
-
Product
Multi-Cluster Sources
-
Our complete line of sources can be configured in a Tri-Source configuration. Clustered sources are a vital part of effective seismic exploration. The destructive effects of the air blast associated with a discharging air source are made worse by clustering. In order to maintain the separation between air sources within a cluster, it is necessary to mechanically constrain the sources with rigid bars.
