System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
Product
Electrical Ground Support Equipment:
EGSE
-
Keysight provides a variety of configurable test systems for satellites and satellite flight hardware; including Solar Array Simulators, Battery Simulation and Conditioning, RF signal simulation and analysis as well as fully custom solutions.
-
Product
Data Block Mating Table
VG Series
-
*Aircraft, Consumer Electronics, Networking, Telecommunications and Test Systems*Custom Blocks can be designed for your specific applications please contact your local sales person to find out more
-
Product
Continuous Time Interval Analyzers
GT668PXI-15
-
GuideTech’s GT668PXI-15 PXI 3U form factor, meets industrial standard chassis with an expandable platform, achieving optimal test system at low cost. High accuracy 50MHz time base with NIST traceable calibration.
-
Product
Battery Checker
SK-8551
-
Total condition check for 12V (24V) batteries. (Truck, Marine, Industry etc.)Battery check, Engine start performance, Charging system tests.
-
Product
PXI Very High Density Versatile 2 Amp Multiplexer
40-612A-002
Multiplexer Module
The 40-612A Very High Density Versatile Multiplexer module features a wide range of software selectable switching configurations. It is especially useful where a number of high density multiplexers are required with the option of easily altering the channel count as a test system evolves. Typical applications include signal routing in ATE and data acquisition systems. The 40-612 module uses high quality electro-mechanical relays, connections are made via a front panel 160 pin DIN41612 connector. The module can be software configured into one of a large number of different multiplexer modes. Relays allow the multiplexer banks to be set in 1 or 2 pole mode and inter-bank switching enables the channel count to be increased up to a maximum of 128
-
Product
Measurement System For Testing & Binning Of Back-End LEDs
TP121-TH
-
The photometric specifications of LEDs must meet very high tolerance requirements regardless of whether they are to be used in general, automotive or other specialist lighting applications. This is often a problem since the manufacturing tolerances of LEDs can be higher than those permitted in the end-use applications. Also, LED binning by LED manufacturers in order to classify LEDs based on their tolerances is performed with flash mode testing using pulsed current flow. However, end-use applications of the LEDs often operate in constant current mode and with significant thermal effects. The sophisticated LED processing industry therefore requires measurement devices that can be used for both manufacturer-compliant pulsed mode, as well as constant current operation mode. When the LEDs are run in constant current mode, the junction temperature has significant influence on the performance and lifetime of the LED. Therefore, test systems should be able to test the LEDs at specific junction temperatures.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 3.55kΩ
50-298-123
Programmable Resistor Module
The 50-298-123 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 3.55kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Source Measure Unit
Source Measure Unit
PXI Source Measure Units (SMUs) combine high-precision source and measure capability with features designed to reduce test time and increase flexibility. These features include high channel density for building parallel SMU test systems, deterministic hardware sequencing for minimizing software overhead, and high-speed update and sample rates for quickly changing setpoints and acquiring data. Additionally, the flexible sampling rate and streaming capability of PXI SMUs allows you to use the instrument as a digitizer to capture transient behavior, and the digital control loop gives you the ability to adjust the transient response of the instrument. The ability to change the transient behavior of the SMU, called SourceAdapt, reduces SMU settling time and minimizes overshoot and oscillations, even with highly capacitive loads.
-
Product
Power Meter
P-Series
-
The N8262A is a compact and slim LXI-compliant P-Series modular power meter. The N8262A helps you to reduce your test system size and enables LAN-based automated power measurements. Owing to LXI test standardization and its interoperability with existing test assets, your system can be up and ready in no time.
-
Product
Modulation Distortion Up To 125 GHz
S930712B
-
S930712B enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 125 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S93072B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
20 Slot, 3U PXI Chassis
GX7300 Series
Chassis
The GX7300 Series mainframes are 20-slot PXI chassis that can accommodate up to 19 instruments as well as a PXI controller (an embedded CPU or a PXI bus expander interface such as a MX interface). The 3U form-factor provides a compact test system foot print and provides users with the flexibility to employ both PXI and Compact PCI 3U modules.
-
Product
Test System
UltraFLEX
Test System
The UltraFLEX test system delivers the power and precision you need for complex SoC devices built for mobile applications, networking, storage or high-end processing. Choose UltraFLEX when your device mix and throughput goals demand the highest speed, precision, coverage and site count.
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 3Ω To 52.4kΩ
50-298-033
Programmable Resistor Module
The 50-298-033 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Universal Frequency Counters
GT210PXI-2
-
GuideTech’s GT210PXI-2 3U form factor, meets industrial standard chassis with an expandable platform, achieving optimal test system with optimal cost. The ability to precisely resolve frequency and time yields both increased accuracy as well as reduced measurement time.
-
Product
Rotor Test Systems
-
Automation Technology's RTS-3800 Rotor Test Systems offer an unparalleled ability to test the quality of die cast or PM rotors. The RTS-3800 is packed with standard features and like all of ATI's 3800 Series Test Systems; the RTS-3800 is backed by ATI's industry leading two-year limited warranty.
-
Product
Micro Ohm Meter 200A
Micro Centurion II
-
Raytech Digital Micro ohm meter, Micro-Centurion II, was designed for high degree of accuracy to measure very low resistances. This technology was then packed into a portable test system to be used by apparatus manufacturers, rebuild shops, and electrical maintenance crews. This intelligent system has an easy to use operation screen, which allows quick selection of the current level and resistance level to be measured.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 2.04k Ohm
50-293-022
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
G12x Tabletop
-
The G12x Receiver has four removable rubber feet below the platform and also allows for permanent tabletop mounting. Available with 15" or 20" platforms. The G12x accepts ITAs designed for both the G12 and G12x allowing versatility with your test system.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm
50-294-032
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Multiport JTAG Tester
XJQuad
-
XJQuad is a 4-port version of the XJLink2 USB-to-JTAG controller targeted at PCB manufacturers. It is supplied with XJRunner software for running XJDeveloper test systems. With a range of special features it is particularly suitable for concurrent/parallel testing on the production line. Each of the four ports has a high-speed interface which can be connected to up to four JTAG chains on each Unit Under Test (UUT).
-
Product
Noise and Vibration Testing
-
Electronic Systems of Wisconsin, Inc.
ESW's unique Noise & Vibration Test Systems come fully equipped with the latest industry features. The on-screen operator display in our testers make it easy to set-up, read, track and record your noise or vibration information. We work directly with you to determine the best solution that will work for your application. Our data logging make sure that important data is stored and available for download for future reference. ESW's design engineers work to make sure the testing interface is easy for your operators to use. We work closely with our customers to make sure that your unique testing needs are met. Please see the slideshow below to see some of our Noise & Vibration Testers.
-
Product
PXIe-5451, 145 MHz, 16-Bit, 512 MB, PXI Waveform Generator
781204-02
Waveform Generator
PXIe, 145 MHz, 16-Bit, 512 MB, PXI Waveform Generator—The PXIe‑5451 is a 145 MHz, dual‐channel arbitrary waveform generator capable of generating user-definied waveforms, standard functions, and I/Q communications signals. It is an ideal instrument for including in systems for testing devices with I/Q inputs, or as the baseband component of an RF vector signal generator as wells as time-domain signals like envelope tracking. The PXIe‑5451 also features onboard signal processing (OSP) functions that include pulse shaping and interpolation filters, gain and offset control, and a numerically controlled oscillator (NCO) for frequency shifting. The PXIe‑5451 also features advanced synchronization and data streaming capabilities.
-
Product
Environmental Control System Test Platform
Test Platform
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
Product
PXI High Density Precision Resistor Module, 4-Channel, 2.5Ω to 472Ω
40-298-120
Programmable Resistor Module
The 40-298-120 is a high density programmable resistor module with 4 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Midirack - 120 x 60 x 80 cm
OTP2-Modul-Nr002
-
The rack serves as the basic framework for your individually designed test system. Various OTP² modules can be installed in the 120 x 60 x 80 cm rack in order to meet the most varied of test requirements.The modular architecture of the OTP (Open Test Platform) is based on a flexible instrumentation matrix, LXI-based sources and measuring devices, combined with a high-quality transfer interface for connecting the test adapters. The systems can easily be expanded with customer- and application-specific functions. We use standardization to build cost-effective systems that still fit your requirements exactly.
-
Product
Lamp Cap Temperature Rise Test System
CX-T1
-
Shenzhen Chuangxin Instruments Co., Ltd.
Lamp Cap Temperature Rise Test System is according to IEC60360-1998 and GB2512-2001(Standard method of measurement of lampcap temperature rise). It is used to test the working and environmental temperature as well as temperature-rise of the burner and lamp. It meets the requirement of IEC and GB Standards
-
Product
PXI 16 Bank 5 Channel 1 Pole Multiplexer
40-616-021-16/5/1
Multiplexer Module
The 40-616 16-Bank, 5-Channel, 1-Pole Multiplexer Module forms part of the System 40 PXI Programmable Switching system. The Module consists of 16 electrically isolated banks of multiplexers controlled by a PXI/ PCI interface. Each bank is a 1 to 5 multiplexer and operates with break-before-make action when a new channel is selected. Any Individual multiplexer bank can have a channel set by itself, alternatively, multiple banks can have channels selected simultaneously. The module is suitable for cascading in applications that require large multiplexer systems, it is also suitable for test systems that require the switching of a large number of signals in parallel.
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 1.5Ω to 1.81kΩ
40-253-022
Programmable Resistor Module
The 40-253-022 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Services
-
Being a system developer as well as a system integrator we offer an entire service portfolio. Wherever you have a problem - we have the specialist in our team. We gladly make a feasibility study for a new product, write test specifications or later test applications.Our colleagues are happy to check or calibrate your test system, expand or optimize your test specification, manage the move to another site or train new personnel. In case you plan to build a new factory, our experience might be helpful tp plan of the new test field.
-
Product
JTAG Debugger Software
JSCAN
-
JSCAN lets you view and control JTAG pins in real-time without having to touch your board! With a simple click of your mouse, you can set pins HIGH or LOW and observe the results right on your PC.J-SCAN works independently of any logic inside the JTAG device, you do not need any special firmware, code or logic installed. View and control pins in real-time, program FLASH memories, create test macros, for system test, easy to use graphical interface and affordable.
