Differential Amplifiers
Increase the voltage of multiple input signals to proportionate outputs.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
CAN Interface
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
25 GHz differential probe with ProAxial interface
DH25-PX
Differential Probe
25 GHz differential probe with ProAxial interface.
-
Product
Low Noise Amplifiers
-
LNA amplifier PE15A1000 is rated at 13 Volts DC maximum and 200 mA. Our low noise radio frequency LNA amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial millimeter wave low noise amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
-
Product
Low Noise, High Performance, FTTP High Power Multi-port Optical Amplifier with a Gain Spectrum Band
MX5800 Series
-
Each output port for the optical amplifier has built-in high performance CWDM. Every external up-link optical port of the optical amplifier can conveniently connect with an OLT. Each of the 1550nm (CATV)’s output optical ports will multiplex 1310/1490n’s data stream from an external OLT, reducing the quantity of the components and improving the performance and reliability of the system.
-
Product
PXI Differential Fault Insertion Switch Modules
-
Pickering's PXI Differential Fault Insertion Switch Modules support multiple channels of two-wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to externally applied fault conditions. *Two module types are available: Two wire fault insertion module suitable for CAN Bus and FlexRay.*High bandwidth two wire fault insertion module suitable for Gigabit Ethernet, AFDX and BroadR-Reach.
-
Product
Low Noise Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM low noise amplifier MMICs cover a frequencies from DC to 86 GHz operation for a wide range of applications, including network infrastructure, radar and communication systems. MACOMs portfolio of low noise amplifiers offer a broad array of noise figures, input IP3, and input power in bare die and a variety of package types. Offerings include wideband distributed topologies and self or actively biased configurations tailored to system design needs.
-
Product
Erbium Doped Fiber Amplifier
S-102
-
The EDFA slot module of FOTS system with built-in power booster EDFA module offers a special function that is able to change the optical signal amplification feature variously, which is followed by user’s driving embedded pump LD freely. The output power of eash pump LD can be controlled separately by the program that is set up by user. When an optimum optical signal amplification particularity is needed, it is made up so that it can be materialized by choosing the Default mode provided along with User mode. More stable application of EDFA is possible through the monitoring of the factors such as in/out signal power, gain, alarm status and pump LD enabled by the application of FPGA processor which makes high speed driving possible. It is also set up that user’s present-time monitoring and control through LCD monitor of system main frame or GUI display for remote control can be possible. Through optimization of amplifier gain, noise figure, and saturated output power, this EDFA module will expand test capabilities in systems, components or sub-assembly manufacturing.
-
Product
Fiber Optic Amplifier
-
Shanghai Pubang Sensor Co.,Ltd.
1. High response frequency, detect with super high speed2. Suitable for detecting small objects3. Non-contact, non-destructive detection,can be used in harsh conditions4. Simple mounting by DIN connection
-
Product
RF Tower Top Amplifiers and Receiver Multicouplers
-
Tower-Top Amplifiers (TTA) are high performance, quadrature-coupled low noise amplifiers (LNA) designed to increase the performance of a Base Transceiver Station (BTS) while ensuring reliable communications for critical Public Safety applications.
-
Product
Differential and Compensation Interferometers
-
One- and two-axis differential interferometers measure relative displacement between two objects. The wavelength tracker automatically compensates for environmental changes.
-
Product
Saluki S3871X Series Solid State Power Amplifier (max. 500W output power)
-
S3871X series is a broadband benchtop solid state power amplifier and incorporates the patended spatial power combination technology. It is designed to have features of broad bandwidth, high gain, high power, wide dynamic range, low spurious signals and extremely load tolerant. These features enable the amplifier to be used as a cable test instrument covering multiple frequency bands.*Wide frequency range, 9kHz to 110GHz, max. 500W output power*
-
Product
200 MHz, 3.5 pF, 1 M Active Differential Probe, ±20 V
T3LVD20-200
Differential Probe
200 MHz, 3.5 pF, 1 M Active Differential Probe, ±20 V.
-
Product
Low Differential Pressure Switch -
1800
-
Essential for industrial environments, the Series 1800 combines small size and low price with 2% repeatability for enough accuracy for all but the most demanding applications. Set point adjustment inside the mounting stud permits mounting switch on one side of a wall or panel with adjustment easily accessible on the opposite side. UL and CSA listed, and FM approved.
-
Product
4-Quadrant Power Amplifier PHIL
PAV15000
-
PAV Series phil 4-quadrant power amplifier is based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
PCIe 16 Bit Multi-Purpose Digitizer - up to 80 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5943-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Hydrophone Booster Amplifier
-
Optional enhancement to the basic hydrophone measurement system to provide further amplification of the hydrophone signal.
-
Product
Low Voltage Differential Signaling (LVDS)
-
Available in QML-Q and QML-V processing flows, CAES LVDS solutions meet all of the stringent mechanical qualification requirements defined in MIL-PRF-38535.
-
-
Product
RF Amplifier Modules
-
Analog Devices RF amplifier modules offer high linearity, low noise figures, and low phase noise, as well as low power consumption. These devices are all fully specified over frequency and temperature for use in a variety of applications.
-
Product
HandyScope HS6-DIFF With SafeGround: 500 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-500XMG-W5
-
The only oscilloscope in the world that has:- SafeGround, differential input channels that can be switched to single ended.- CMI interface.- USB 3.0 interface, 5Gb/s data transfer- Lowest noise
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 125 MS/s on 20 Channels, 80 MS/s on 40 Channels, 40 Single-Ended Inputs, 20 True Differential Inputs
DN6.596-40
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Minihelic II Differential Pressure Gages
2-5000
-
Combining clean design, small size and low cost with enough accuracy for all but the most demanding applications our Minihelic II gage offers the latest in design features for a dial type differential pressure gage. It is our most compact gage but is easy to read and can safely operate at total pressures up to 30 psig.
-
Product
Erbium Doped Fiber Amplifier
EDFA
-
EDFAs are based on the light amplification in erbium-doped fiber, which are optically pumped by means of 980 nm or 1480 nm light sources. In this way, the light of a larger wavelength within the C or L band applied to the input of the amplifier is amplified, thus widening the range of optical communication links. EDFAs typically operate in saturation and the average signal power determines the average gain. The dynamics of EDFA are unaffected by the sequence and dynamics of a digital signal or channel interaction in DWDM systems. As a result, multiple channels can be bundled within the total erbium spectral amplification bandwidth. However, the total average output power in both cases is determined by the saturation power of the specific EDFA.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 40 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5933-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Composite 1×6 Video Distribution Amplifier
VDA106
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Transimpedance Amplifiers
-
Advanced Science and Novel Technology, Co., Inc.
Broadband transimpedance amplifier for low noise receiver side applicationsFeatures automatic input offset control and a peak detector8GHz of analog bandwidth for limiting of input data60dB of transimpedance differential gain15pA/sqrtHz of input referred noise density (0.1 to 10GHz)CML output interface with 50 termination and 225mVp-p single-ended swingSingle +3.3V power supplyPower consumption: 250mWExhibits low jitter and limited temperature variation over industrial temperature rangeUnpackaged bare die
-
Product
General Purpose Op Amplifiers
-
When your design requires general purpose op amps, Analog Devices broad portfolio of high speed op amps, precision op amps, and instrumentation amplifiers deliver the unmatched performance and exceptional value that you’re looking for. Explore our selection of op amps by your necessary parameters and find expert, system-level advice to address your design issues by consulting with ADI resources such as EngineerZone.
-
Product
Two Axis Differential Interferometer
10721A
-
The Keysight 10721A Two Axis Differential Interferometer, when used in multiple axis applications, simultaneously makes two differential measurements linear and angular (yaw) displacement. Both measurements reference external mirror mounted to an object such as a column or inspection tool. The 10721A provides high immunity to unwanted interferometer displacement, such as thermal expansion. It is a modular, compact design with monolithic optics for maximized mechanical stability. Use of a small 3 mm beam helps decrease Abb offset error. The 10721A is similar to the 10719A Single Axis Differential Interferometer, except that it provides an additional measurement axis.
-
Product
1.5µm PM Ev-Yb Fiber Amplifier ( PM EYDFA )
HAPM5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM5000 is a C-Band Polarization Maintaining Optical Amplifier which worked in 1540~1570nm operating wavelength. Adopt Polarization Maintaining (PM) Multiclad Ev-Yb fiber, output optical power range 27~37dBm(0.5W~5W) ， extinction ratio >20dB.
-
Product
1U, Rack Mount, Pulse Distribution amplifier
A5000P
-
The Quartzlock A5000P is a 1U, rack mount, pulse distribution amplifier
