PXI Carriers
-
Product
PXI 4x4 10GHz Matrix with Termination
40-787-518-4X4-T
Matrix Switch Module
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module
-
Product
PXI Resistor Module 24-Channel (no resistors fitted)
40-280-021
Programmable Resistor Module
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
Product
PXI 5A Power Multiplexer, 2-Bank, 24-Channel
40-651A-002
Multiplexer Module
The 40-651A-002 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
Product
PCI to PXI Remote Control Kit
41-921A-001-KIT
Remote Control Interface
This kit provides a seamless connection between a control PC’s PCI interface and a PXI chassis. The PCI to StarFabric module (51-921A) resides in one of the controllers PCI slots and provides two independent StarFabric serial interfaces, each capable of driving a separate PXI chassis.
-
Product
PXI 64-Channel Digital Output Module
40-412A-021
Digital Output Module
The 40-412A-021 (PXI) and 42-412A-021 (PXIe) are 64-Channel Digital Output modules with high output voltage and current capability. The outputs can be used for high or low drive and each channel is capable of sourcing 0.5A from the high side or 0.5A sink on the low side. Accidental operation of both high and low side driver on the same channel is prevented by the supplied driver. Outputs are fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side driving, the voltage source is supplied externally, allowing the module to drive high capacity loads separate from the chassis power supply. For low side driving, the external source is not used and the module’s output operates an open collector or open drain driver.
-
Product
PXI High Density MUX BRIC, 32-Chan, 20-Pole
40-570-314
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI BRIC8 1Resource Distributor, 4Bus Matrix
40-569-114
Matrix Switch Module
The 40-569 PXI Matrix BRIC provides a range of high-density bus matrix inputs and resource distributor bussed configurations capable of switching up to 2A and up to 100VDC/70VAC. These large PXI matrix modules are available in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781339-04
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
PXI Express Board Virtex-5 ADC Module
SMT790
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
PXIe-5622 , 150 MS/s, 16-Bit PXI IF Digitizer
780412-02
IF Digitizer
150 MS/s, 16-Bit PXI IF Digitizer—The PXIe‑5622 includes onboard signal processing (OSP), which enables features such as quadrature digital downconversion (DDC), real DDC, and anti-alias filtering. The PXIe‑5622 is ideal for communications applications because of its high dynamic range front end and a high-throughput PXI Express interface that allows it to stream IF data to disk for hours at the full sample rate.
-
Product
PXI Arbitrary Waveform Generators
-
Keysight's PXI arbitrary waveform generator (AWG) deliver unprecedented performance for creation of complex wideband waveforms. High sampling rate and high bit resolution provided in a single instrument enable designers to create ideal waveforms for accurate test of radar, satellite and frequency agile systems. Providing up to 500 MHz of modulation bandwidths and over 65 dBc of spurious free dynamic range, PXI arbitrary waveform generators can be combined with a wideband I/Q upconverter to achieve modulation bandwidth of 1 GHz at microwave frequencies for realistic signal simulations for IF and RF subsystem test.
-
Product
PXI 16 Channel Switch Simulation Module
40-480-121
Switch Simulation Module
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
PXI 2 Amp MUX, Single 16-Channel 2-Pole
40-635-102
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXIe8862, 2.6 GHz 8-Core PXI Controller
788167-33
Embedded Controller
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
Product
PXI 3A Power MUX BRIC, 24-Channel, 12-Pole
40-571-306
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXIe-5624, 2 GS/s, 12-Bit PXI IF Digitizer
783132-01
IF Digitizer
The PXIe‑5624 is optimized for superheterodyne receiver architectures. It features an onboard digital downconverter, which converts IF signals to I/Q data. As a result, you can use the PXIe‑5624 either as part of a PXI Vector Signal Analyzer or as a stand-alone IF digitizer.
-
Product
224 Channel Digital I/O Modular PXI Card
GX5731
Digital I/O Module
The GX5731 is a 6U modular digital I/O card with 224 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5731 offers the highest density in the industry for a single PXI plug-in board. Of the 224 channels, 128 support TTL levels with the direction of each group of eight channels programmable as input or output. The other 96 channels can be used for customized I/O using MTS' GX57xx series I/O modules.
-
Product
PXIe-5667, 3.6 GHz PXI Vector Signal Analyzer
782366-03
Signal Module
PXIe, 3.6 GHz PXI Vector Signal Analyzer - The PXIe‑5667 is optimized for spectrum monitoring applications such as radio monitoring, interference detection, spectrum regulation, and related applications in line with ITU recommendations. It features real-time signal analysis and advanced signal processing using the capabilities of the built-in FPGA. Additionally, the PXIe‑5667 includes options for various frequency ranges and instantaneous bandwidth.
-
Product
PXI 3A Power MUX BRIC, 4-Channel, 12-Pole
40-571-301
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for six M.2 or NGSFF (NF1) PCIe SSD Modules
SKU-086-36
-
This Squid PCIe Carrier board can support up to six M.2 or NGSFF (NF1) PCIe SSD (solid state drive) modules, with M-key. Supported module dimensions are 2280 or 22110 in length, and a width of up to 32 mm. SSD modules of any capacity may be used, from any vendor, and in any combination.
-
Product
PXI 2A Multiplexer, 2-Bank, 16-Channel 4-Pole
40-614-012
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
PXI Stimuli
-
We offer a broad range of PXI Instruments and Cards including PXI chassis, counters, switching, user power supplies, digitizers, arbitrary waveform generators, a precision standards module and digital I/O instrumentation.
-
Product
PXI Dual 2 Channel Optic Mux FC/PC
40-855-022
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 16 Channel
41-761-003
Simulator
The 41-761-003 is a low voltage 16-channel output module ideal for simulating theoperation of a thermocouple, also available with 32, 24 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
Product
Carrier Card
SPR518
-
The SPR518 provides a smart upgrade path to affordably replace the existing SPR418A PCI Express (PCIe®) carrier for XMC modules. The new card provides for unimpeded data transfers within traditional PCs, at the full rate supported by the mezzanine card.
-
Product
PXI Switches
-
The PXI general purpose switch modules deliver fast, reliable switching in a variety of configurations. Cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids with independent, single-pole, double-throw (Form C) or single-pole, single-throw (Form A) switches in a single PXI module. Choose between the high-speed, long-life reed relays capable of switching up to 100Vrms with up to 1A and 25W of power, or the higher power armature relays capable of switching up to 250Vrms, with up to 2A and 60W of power. The general purpose line also includes a module that offers the performance you need to switch heavy loads with up to 300W (DC resistive load)/1250W (AC resistive load).
-
Product
PXI 10A Fault Insertion Switch 10-Chan 1-Bus
40-199-001
Fault Insertion Unit
The 40-199 is a 10 Channel Fault Insertion switch designed for the simulation of fault conditions in automotive/avionics applications, involving the reliability testing of safety critical controllers.
-
Product
PXI Very High Density Multiplexer, 10-Channel 8-pole
40-670C-021-10/8
Multiplexer Module
The 40-670C-021-10/8 is a 10-channel, 8-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
PXI Amplifier And Attenuator Modules
-
Pickering's PXI Amplifier and Attenuator Modules include our accurate DC to 3GHz programmable attenuator has a 1dB step resolution, allowing it to adjust signal amplitudes for optimum measurement by other devices. The other programmable attenuator available has a bandwidth between 10MHz and 6GHz available in triple or hex formats.
-
Product
PXI 8 Channel Switch Simulation Module
40-480-021
Switch Simulation Module
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions.
