JTAG Emulators
Exercise a processor's (DUT) on-chip debug services to perform JTAG emulation and debug.
See Also: JTAG, JTAG Controllers, JTAG Debuggers, iJTAG, P1687
-
-
Product
JTAG Emulators
XDS100v2 Series
-
The XDS100-class JTAG Emulator is an ultra-low-cost entry level JTAG debugger for TI devices. Blackhawk offers two models, each with two JTAG target connections. One model includes TI JTAG connections for 14-pin TI and 20-pin cTI JTAG headers. The other model provides ARM 10-pin and 20-pin JTAG connections. Both models are identical in software and device support except for the the target connections, so pick the one that matches your target board connection.
-
Product
Advanced JTAG Emulators
-
Blackhawk offers JTAG Emulators ranging from entry level to full-capability debug probe models supporting System Trace (STM), starting at $99. This includes XDS100v2, XDS200 and XDS560v2-class models that are compatible with Code Composer Studio.
-
Product
JTAG Emulator
Blackhawk USB560v2
-
The Blackhawk USB560v2 STM emulator has System Trace capability, along with a USB powered interface.
-
Product
JTAG Emulator
Spectum Digital XDS510-USBPlus
-
The Spectrum Digital XDS510-USBPlus enhanced JTAG emulator is low cost, along with a USB powered interface.
-
Product
JTAG Emulator
Blackhawk USB510L
-
The Blackhawk USB510L JTAG emulator is low cost, and has a USB powered interface.
-
Product
JTAG Emulator for BAE Systems RAD750 Microprocessors
CodeRunner JTAG Emulator
-
Designed for the most hazardous high radiation environments, the BAE Systems RAD750 radiation hardened PowerPC microprocessor is the most advanced processor offered to the space community. From the Mars Reconnaissance Orbiter to the Curiosity Rover, the RAD750 microprocessor has proven time and again to lead the industry in quality, performance, and cost.
-
Product
JTAG Emulator
Spectum Digital XDS560v2-STM
-
The Spectrum Digital XDS560v2-STM emulator has System Trace capability, along with a USB powered interface.
-
Product
JTAG Emulator
Blackhawk XDS560v2
-
The Blackhawk XDS560v2 STM emulator has System Trace capability, along with USB powered and LAN interfaces.
-
Product
JTAG Emulator
Spectum Digital XDS510-USB
-
The Spectrum Digital XDS510 JTAG emulator is low cost and has a USB powered interface.
-
Product
High-Performance JTAG Emulators
XDS560 Series
-
Blackhawk XDS560-class models are offered with PCI, USB, and Ethernet host interfaces. These XDS560 models support the first generation of TI XDS560-class high-speed JTAG connection between Code Composer Studio and the target device.
-
Product
Regenerative AC Emulator, 1200 VAC, 65 A, 90 KVA, 3‑Phase
SL1213A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Regenerative AC Emulator, 600 VAC, 63 A, 45 KVA, 3‑Phase
SL1202A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Regenerative AC Emulator, 600 VAC, 63 A, 30 KVA, 3‑Phase
SL1201A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Scienlab Dual-Range Regenerative AC / Grid Emulator, 600 / 1200 VAC, 63 / 32.5 A, 45 KW / 66 KVA
SL1214A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
Scienlab Dual-Range Regenerative AC / Grid Emulator, 600 / 1200 VAC, 63 / 32.5 A, 90 KW / 135 KVA
SL1215A
-
The SL1200A series was designed to handle all your 3-phase AC test needs up to 1200 VAC, from 30 kVA to 630 kVA without the need for a transformer. Two voltage ranges are available: 600 VAC and 1200 VAC. The 600 VAC models are ideal for low voltage inverter test as well as EV and EVSE charging test applications. The 1200 VAC models allow for (HVRT) testing at the IEC LV-AC limit without the need for a large, complex test setup.
-
Product
JTAG Software
-
Looking for flash programming or JTAG test utilities, we have them. Our software ranges from basic command line utilities to applications that extend the emulator's use in the field or the lab.
-
Product
JTAG Probe
MAJIC
-
MAJIC (Multi-Architecture JTAG Interface Controllers) JTAG Probes are small, stand-alone, processor-based systems that provide an intelligent connection between host-based development tools (the debugger) and an embedded processor via its standardized JTAG debug logic IP macrocell.
-
-
Product
Network Emulator
Netropy® 100G
-
Developed for the pre-deployment testing and validation of high-speed 100GbE networks, the 100G is capable of precisely emulating 25, 40, 50 and 100Gbps WAN links. It allows service providers and storage system manufacturers to validate how WAN impairments--such as latency, packet loss or congestion--will affect performance over all data center links prior to going to market. Available 1/18
-
Product
Network Emulator
KMAX
-
The KMAX network emulator helps network engineers test and measure performance in order to identify and remove defects. Network emulators turn well behaved development and test networks into the kind of slow, congested, and less-than-reliable services encountered on the internet. In addition, unlike the real internet, network emulators allow the operator to control these conditions so that products and apps can be subjected to controlled and repeatable tests, by routing selected packets through a series of impairment nodes.
-
Product
JTAG / BDM Instrumentation
-
High-speed and static 3U and 6U PXI and PCI digital I/O instrumentation. Offering test rates to 200 MHz and programmable logic levels of -10 V to +15 V, our digital products feature the highest performance and most cost effective digital test solutions in the industry.
-
Product
JTAG Functional Test
JFT
-
JFT comprises a series of software modules that support boundary-scan test and programming activities under Python, National Instruments LabVIEW and Microsoft .NET framework. Using JFT users can create JTAG/boundary-scan test application scripts, VIs or programs for PCB assemblies and systems that control individual driver/sensor pins, groups of pins declared as variables or register bits. These applications are typically used to test logic devices or mixed signal clusters and can also be transformed into re-usable test 'modules'. Pairing JFT with JTAG CoreCommander emulative test modules gives an effective, low-cost system for performing tests through embedded device peripherals (ADCs, Memory Controllers etc..)
-
Product
high-speed JTAG debugger
Bus Blaster v4
-
Bus Blaster is an experimental, high-speed JTAG debugger for ARM processors, FPGAs, CPLDs, flash, and more. Thanks to a reprogrammable buffer, a simple USB update makes Bus Blaster v2 compatible with many different JTAG debugger types in the most popular open source software.
-
Product
WAN Emulation
-
Net.Storm is able to simulate any network condition to check how tolerant your services, protocols and devices are when quality / capacity degradations occur. It replicates accurately combined effects such as packet delay, errors, loss, bandwidth variations, traffic shaping and traffic policing.VoIP.Master is an advanced turn-up solution for VoIP allowing technicians to deploy VoIP thanks to its emulation capabilities that permit users to connect VoIP.Master to SIP trunks and networks emulating an IPBX, making multiple VoIP calls ensuring the trunk is operational and performing to pre-agreed SLAs.
-
Product
JTAG Live Controller
-
The JTAG Live Controller is USB connected and powered and features a single test access port in JTAG Technologies standard 10-way IDC pin-out. The JTAG Live controller is a smart, low-cost and easy-to-use USB JTAG/Boundary-scan interface.
-
Product
Emulation Adapters
-
With some of the more advanced 32-bit microcontrollers and SoCs, the full program and data trace capabilities of the device are not made available on production silicon. Instead, semiconductor vendors provide special 'emulation devices'. These typically feature more pins than the production device, thereby providing the interface to the trace interface.
-
Product
Emulator
GCI E84
-
The GCI E84 Emulator is the world's leading tester for development, implementation and qualification of products that must comply with the SEMI E84 Standard. It provides the industry-standard automated test plans that are utilized by virtually every 300mm FAB and equipment manufacturer worldwide. GCI testers are the only solutions that guarantee 300mm factory automation interoperability.
-
Product
Network Emulation System
Mini Maxwell
-
Mini Maxwell -- Easy to use, portable, network emulator. Mini Maxwell''''s low cost of $1995 can fit into any testing budget. The Mini Maxwell is great if you have low power requirements, or need ultra quiet operation. Mini Maxwell supports packet drop/loss, duplication, delay (latency)/jitter, reorder, and burst. Includes: processor, memory, and three Ethernet interfaces in one enclosure with separate power supply, Linux OS, Mini Maxwell network emulator engine, graphical user interface, and 90 Day Warranty.
-
Product
Base Station Emulator
SUTP 5018
-
Designed to create a custom cellular environment to serve testing and characterization needs. The combination of high power, real-time computing and the software defined radio platform enables this instrument to create your own cells for testing in a compact size and cost-efficient way.
