Filter Results By:
Products
Applications
Manufacturers
Actuators
Converts a signal to an action.
-
product
General Purpose I/O Modules
HY-TTC 30XH
The HY-TTC 30XH is a CANopen based, user-friendly and smart Input/Output module that can be utilized as flexible control system extension in mobile applications. HY-TTC 30XH is used in combination with, and controlled by a master electronic control unit, communicating with the slave module via the standardized CANopen® protocol. By mounting the master control unit centrally on the machine and the I/O modules close to the sensors or actuators, a distributed electronic architecture can be implemented in order to reduce mounting time and cost for cabling.
-
product
Single Channel High Voltage Linear Amplifier
F10A
The F10A is a general purpose broadband linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
Linear Actuators
Electrak 1
The Electrak 1 actuator is completely self-contained and sealed for indoor and outdoor use. Functionally, these models are easily interchanged with comparably sized hydraulic or pneumatic cylinders. Used on intermittent duty applications Electrak 1 actuators provide consistent, repeatable performance in the most rigorous operating conditions including extreme temperatures and humidities.
-
product
NI-9482, 4-Channel, SPST Relay, 60 VDC (1 A)/250 VAC (1.5 A) C Series Relay Output Module
782999-01
The NI‑9482 directly connects to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to an electromechanical relay for switching signals up to 60 VDC (1 A) or 250 Vrms (1.5 A), features channel‑to‑channel isolation, and has a LED that indicates the status. The shock and vibration rating for the NI‑9482 is limited compared with other CompactDAQ and CompactRIO modules because of the mechanical relays on the module.
-
product
Electric Actuators
CK
Rotork has developed the CK actuator range to provide a state-of-the-art product to the valve industry. The CK product range includes standard multi-turn actuators through to intelligent Centronik equipped actuators.
-
product
Solenoid Valves
Omega's solenoid valves for fluid control are used for on/off flow control, directional control, and to pilot pneumatic spring return and double acting actuators. Available with AC or DC solenoids.
-
product
Business Machines
Innovation in 3D Printing, Automated Lighting, Mobile Communications, Commercial Printing and other industries is driving demand for linear actuators, lead screws and rails as well as DC motors. Haydon Kerk Pittman’s diverse product range and technology often makes it the preferred single source supplier of components or custom sub-systems. Whether you choose stepper, DC brushed or brushless technology as part of your rotary or linear mechanism, Haydon Kerk Pittman can provide the optimum solution.
-
product
Switches
Broad / flexible product line100% Quality TestedChoose from a variety of actuators, termination and mounting stylesRoHS CompliantPDF file Basic Switch Technical InformationBasic Switch Technical InformationPDF file Tactile Switch Technical InformationTactile Switch Technical InformationPDF file Switch Selection Guide - 2014Switch Selection Guide - 2014
-
product
Linear Positioning
ServoBelt Linear
ServoBelt Linear actuators redefine the classic belt drive, putting belts to work in an entirely new way that reduces the positioning errors and speed limitations of conventional belt drives.
-
product
PXIe-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module
787358-01
PXIe, 96-Channel, 5 V, TTL/CMOS, 24 mA PXI Digital I/O Module - The PXIe-6509 can directly drive external digital devices such as solid-state relays (SSRs). You can configure each line for input or output and you also can configure each line with a user-configurable pull-up or pull-down resistor. Using the PXIe-6509 programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. The PXIe-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. The PXIe-6509 provides programmable input filters for eliminating glitches or spikes and for debouncing digital switches or relays through a software-selectable digital filter.
-
product
Process Control Actuators
SM-6000
*Torque range up to 35,256 Nm (26,000 lbf.ft)*Up to 313° rotation*Double O-ring sealing*Continuous unrestricted modulating duty*Manual override standard*HART®, Profibus® & Foundation Fieldbus® available*Automatic torque limiting*Self-locking drive system to hold in last position and prevent backdriving up to 125% of torque rating*AC input power (1-phase and 3-phase)*Temperature range from -40° F to 185° F (-40° C to 85° C)*Manual override standard
-
product
PCI-6516, 32-Channel, ±30 V, Source Outputs, Bank-Isolated Digital I/O Device
779082-01
The PCI-6516 is an industrial digital output interface, with one bank of channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6516 module is an industrial digital I/O interface, with all channels on an isolated bank. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6516 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
product
Rotary Actuators
A line of of products that combine a high rigidity hollow rotary table with a closed loop stepper motor and driver package. It retains the ease of use of a stepper motor, while also allowing for highly accurate positioning of large inertia loads.
-
product
Digital Pressure Calibrator
DPC-30
The digital pressure calibrator is a highly accurate, digital calibrator for pneumatic field instrumentation, including valve actuators, P/I transmitters, controllers, gauges, switches, and recorders.
-
product
40mA Multi-Channel Amplifier
For the precise nanometer movement of actuators and other piezo products, an amplifier is required. Multi-channel amplifiers allow you to control multiple actuators or piezo products with a single amplifier. The NV40/3 piezo amplifier was designed for controlling low voltage piezo elements. It includes a voltage amplifier, a display and a PC-interface. The high-resolution display shows the voltage of the actuator, along with the mode of operation and the temperature inside the amplifier.
-
product
Nanopositioner
P-616 NanoCube
Physik Instrumente GmbH & Co. KG
Compact Parallel-Kinematic Piezo System for Nanopositioning and Fiber Alignment. In a parallel-kinematic multi-axis system, all actuators act directly on a single motion platform. This means that all axes can be designed with identical dynamic properties, which reduces the moved mass considerably. Further advantages: It is possible to make the parallel-kinematic system more compact than serial stacked or nested systems. The errors and masses of each individual axis do not accumulate.
-
product
Motion And Position
Omega has all your motion control products in one place. We have motors, actuators, motor controls, pneumatic components, proximity sensors, rotary displacement encoders and more.
-
product
Radiation Survey Device
DRG-T
The DRG-T radiation survey device is designed for use in special-purpose vehicles for continuous control and measurement of exposure dose rate (EDR) of gamma and X-ray radiation, as well as for providing audio and visual alarm of its dangerous levels and for issuing commands to start the actuators of protection equipment.
-
product
PCI-6519, 32-Channel, ±30 V, 16 Sink/Source Inputs, 16 Sink Outputs, Bank-Isolated Digital I/O Device
779085-01
The PCI-6519 is an industrial digital I/O interface, with two banks optically isolated channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6519 module is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6519 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
product
Fluid Power Actuators
Skilmatic
The Skilmatic range of actuators offer a unique and reliable solution for electric failsafe and modulating control for both quarter-turn and linear valves and dampers. They combine the simplicity of electrical operation with the precision of hydraulic control and the reliability of mechanical spring return or accumulator fail-safe action.
-
product
Simulation Systems
Bloomy offers Simulation Systems for Hardware in-the-Loop (HIL) and open loop test of electronic controls and mechanical actuators for all types of transportation and defense systems including aircraft, rail, automobiles and ships. These systems, now deployed at major aerospace, locomotive and military manufacturers and research facilities worldwide, provide world-class, high-fidelity simulated environments for use in both closed-loop and open-loop testing. Because Bloomy’s Simulation Systems are largely constructed from COTS components, time to first test can be reduced significantly, and their highly-customizable nature allows your test system experts to provide your unique IP to differentiate your product from your competitors.
-
product
PCI-6518, 32-Channel, ±30 V, 16 Sink/Source Inputs, 16 Source Outputs, Bank-Isolated Digital I/O Device
779084-01
The PCI-6518 is an industrial digital I/O interface, with two banks optically isolated channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6518 module is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6518 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
product
Probing, Monitoring & Setting
Marposs offers solutions and equipment that make your machine tool an instrument of unprecedented precision, productivity and reliability. Touch probes and laser-based tool setters hold the cutting process accuracy in check. Our balancing actuators and many dedicated sensors guarantee that your machine tool's functional processes never deviate from their specified set points.
-
product
PCI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, Digital I/O Device
778833-01
The PCI-6528 is an industrial, parallel digital I/O interface.With programmable power-up states, you can configure the initial output states in software, to ensure safe … operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
product
Fanless Robotic Controller with Intel® Xeon®/Core™ Processor
ROScube-I
ADLINK ROScube-I is a real-time ROS 2 enabled robotic controller based on Intel® Xeon® 9th Gen Intel® Core™ i7/i3 and 8th Gen Intel® Core™ i5 processors featuring exceptional I/O connectivity supporting a wide variety of sensors and actuators for unlimited robotic applications. Also supported are Intel® VPU and NVIDIA GPU cards for computation of AI algorithms and inference. The extension box allows for convenient functional and performance expansion. ROScube-I supports the full complement of resources developed with ADLINK Neuron SDK, a perfect platform for development of industrial use service robotic applications such as autonomous mobile robots (AMR) and autonomous mobile industrial robots (AMIR).
-
product
Chassis and Safety ICs
ST is a world-class supplier of IC smart power solutions for all the Chassis and Safety applications, ranging from passive safety, braking, vehicle dynamics and steering systems. Type of devices in ST portfolio are analog and mixed-signal ICs, integrating different functions such as supply modules, drivers for loads and actuators, diagnostic functions, system monitoring and communication interfaces.
-
product
Limit Switches
With its choice of casings, wide range of actuators, variety of connections and high degree of resistance to impact and splashes, Crouzet Switches offers limit switches available in the following ranges: Metal body, Plastic body, Special products and Products for severe environments. Their main characteristics are: IP6x seal, a wide range of actuators (plungers and rollers), rotary heads with momentary action, positive break contacts, compact size, etc. They also offer the option of having special levers, prewiring, connection via ISO cable glands, etc.
-
product
Fiber Switches
Piezo-electric driven switches are especially designed for fast switching – measured in milliseconds. Piezo actuators enable the optical switch to couple optical fibers with an accuracy of a few microns. The piezo driven optical switches are available fiber core diameters of 50 µm up to 600 µm.
-
product
PXI-6512, 64-Channel, ±30 VDC, Source Outputs, Bank-Isolated PXI Digital I/O Module
778969-01
64-Channel, ±30 VDC, Source Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6512 is an industrial digital output interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6512 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
product
Simulation Table
KRD61 6-DOF
KRD61 series 6-DOF simulation table is a closed-loop servo simulation platform consisting of six servo actuators and six sets of dedicated hinges connected at the top and bottom platforms respectively. By virtue of the telescopic movement of the six actuators, the upper platform moves in six degrees of freedom (X, Y, Z, α, β, γ), so various space motion attitudes can be simulated.
