RF Chambers
isolate and supress RF waves.
See Also: Chambers, TEM Cells, Acoustic Chambers, Altitude Chambers, Anechoic Chambers, Climate Chambers, Dust Chambers, Environmental Chambers, ESS Chambers, Humidity Chambers, Refrigerated Chambers, Reverberation Chambers, Salt Spray Chambers, Sound Chambers, Temperature Chambers, Temperature Humidity Chambers, Thermal Shock Chambers, Vacuum Chambers, RF Enclosures
-
-
Product
RF Hybrid Couplers
-
Pasternack RF hybrid coupler series is passive devices that couple part of the transmission power in a transmission line. Our RF hybrid coupler components provide the bandwidth, high directivity and high power that designers need for their most demanding applications. 90 degree hybrid couplers often use two transmission lines set close together so that energy passing through one is coupled to the other. Many Pasternack 90 degree hybrid coupler items are RoHS and REACH compliant. Our RF hybrid coupler series is available with SMA connectors and 3dB coupling values. Power ratings for the 90 degree hybrid coupler product line range from 20 Watts to 50 Watts. 90 degree hybrids have a frequency range that is from 1 GHz to 18 GHz. As with the other over 40,000 RF, microwave and millimeter wave components from Pasternack, this RF hybrid coupler series is in-stock. Not just in stock, but these RF couplers in a hybrid design will also ship the same day as they are purchased.
-
Product
Benchtop Chambers
-
A compact, portable environmental simulation unit designed to fit on laboratory benchtops for testing small products, components, or materials.
-
Product
TSE-12-A Thermal Shock Chamber
-
Did you think that getting a thermal shock chamber was too expensive, required special utilities, and half your lab-space? The TSE-12 thermal shock chamber is the solution. Only 26 inches wide, the TSE-12 transfers product loads between cold and hot zones with a temperature range of -65°C to 200°C.
-
Product
2 GHz Dual 1:4 RF Mux, 75 Ohm Module for 34970A/34972A
34906A
Multiplexer Module
The Keysight 34906A RF multiplexer module for the 34970A/34972A Data Acquisition/Switch Unit offers broadband switching capabilities for high-frequency and pulsed signals. Use it to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation. The RF multiplexers are arranged as two independent 1 x 4 multiplexers, each with a common shield and a switched center conductor. Connections can be made directly to SMB inputs with 2 GHz usable bandwidth, or to the BNC-to-SMB adapters provided with 1 bandwidth. Multiple banks may be cascaded together for applications requiring even larger topologies--create a stubless 16:1 multiplexer in a single frame.
-
Product
PXI-5670, 2.7 GHz RF Vector Signal Generators
PXI-5670 / 778768-03
Vector Signal Generator
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
Product
Dust Chamber Manufacturer
-
Wewon Environmental Chambers Co, Ltd.
Wewon Environmental Chambers Co., Ltd. is a good dust chamber manufacturer and made a 3380 liters blowing sand and dust test chamber for a Vietnam customer last week. The controller system of this 3380 liters dust test chamber can be connected to the computer.
-
Product
PXI Triple 4 To 1 RF Multiplexer, 8GHz 50 Ohm SMA, Terminated
40-882A-003
Multiplexer Module
The 40-881A-003 is a triple 50Ω 4 to 1 RF multiplexer with 8GHZ bandwidth.The 40-881A range of multiplexers have automatic termination of unused signals and are available as a single MUX in one PXI slot, a dual MUX in two PXI slots, or triple and quad MUXs in three slot PXI modules.
-
Product
PXI 16x2 RF Matrix 100MHz 75 SMB With Loop-Thru
40-728-101-L
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI/PXIe RF Matrix, 16x4, 300 MHz, 50 Ω SMB With Loop-thru
42-727A-001-L
Matrix Switch Module
The 40-727A-001-L (PXI) and 42-727A-001-L (PXIe) are 16x4 50 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
RF Wideband Downconverter Solution From 100 KHz To 8 GHz
DC8G100
-
GaGe wideband downconverters are wide frequency coverage receivers that feature a single RF input and 3 standard software selectable IF bandwidths, from 10 MHz to 100 MHz, or 3 optional software selectable IF bandwidths, from10 MHz to 160 MHz. The carrier center frequencies can be tuned from 50 MHz to 27 GHz, using direct digitization below 50 MHz.
-
Product
PXI/PXIe RF Matrix, 16x8, 300 MHz, 50 Ω, SMB
42-724-011
Matrix Switch Module
The 40-724-011 (PXI) and 42-724-011 (PXIe) are 16x8 RF matrix modules suitable for switching frequencies up to 300 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
Product
RF Signal Detector
H-055DRV / 01019
-
The RF Signal Detector / 2G Cellular Phone Detector / Wireless Camera Detector / Bug Detector applies with fuzzy scanning technology to detect peeping cameras, tapping, cellular phones and other radio frequency devices.
-
Product
Microwave Wideband Direct Modulated DFB Transmitters (without RF Amp)
MT50 (40KHz~20GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MT50 series microwave wideband direct modulated DFB transmitter, are able to transmit 20G microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc.
-
Product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 75Ω, SMB
40-837A-002
Matrix Switch Module
The 40-837A-002 (PXI) and 42-837A-002 are 75Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-837A modules.
-
Product
MS-M Style 26-Pin RF Cable Assembly, Female To Unterminated, 0.5m, RG316 Cable
40-979-526-3-0.5m-FU
RF Cable Assembly
This 0.5m long MS-M style RF 26-Pin cable assembly is constructed from RG316 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 68dB/100m at 500MHz. Screwlocks are provided to secure the MS-M style connector to the mating connector.
-
Product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - XMC
Model 71690
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal - levels with up to 60 dB gain- Programmable analog downconverter to I + Q baseband signals - 4 to 40 MHz bandwidth- Two 200 MHz 16-bit A/Ds digitize the I + Q signals synchronously- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1 & 2) interface, up to x8- Clock/sync bus for multimodule synchronization- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Composite Salt Spray Test Chamber
YWX/Q-010X
-
Composite Salt Spray Test Chamber stimulate the actual natural conditions to do accelerated corrosion test, all the testing are based on common states on the natural environmental: such as combine with salt spray, hot air drying, humidity, low temperature and so on. The test samples are widely used on the intense changes in the environment, like automobile parts, aviation equipment, building materials, coating, electric and electrical machinery so on. YWX/Q-150X series is full compliance with ASTM D4728I, EC 60068-2-1, IEC 60068-2-14 and EIA/JEDEC JESD22-110-B standard requirements etc.
-
Product
RF Front-End ICs
-
Analog Devices offers RF Front-End ICs for phased array antenna solutions. These RF Front-End ICsare placed right at the antenna element and can quickly switch between transmit and receive functions in radar applications. The power amplifier on the transmit side is highly efficient operating in short pulse durations. The low noise amplifier on the receive side has a low noise figure with high linearity so that it won’t distort the incoming return signal. The RF Front-End IC also incorporates a high performance switch to toggle between the transmit and receive paths. Highly integrated planar phased array antennae need small form factor solutions, and Analog Devices has integrated the switch, low noise amplifier, and power amplifier into a small surface mount package as well as the decoupling capacitors, providing an optimal solution.
-
Product
Sand and Dust Chamber
-
Designed to test a product’s resistance to extremely dusty, desert-like environments, Thermotron’s D-27 Sand and Dust Chamber provides the capability of meeting specific automotive test standards. Powerful blowers intermittently blow compressed air up through finely powdered dust and then allow the dust to settle back down covering the product.
-
Product
RF Switch Modules
-
Analog Devices RF switch modules include the highest bandwidth switch modules. SPST, SPDT, SP4T, SP6T, and SP8T versions (reflective and absorptive) are available for a wide range of power (up to 27 dBm) applications, including antenna switching, filter switching, and tuner applications.
-
Product
RF Generators
-
RF signal generators are equipment’s used to generate high frequency signals at a particular frequency for testing systems in the lab. RF Signal Generators from the leading manufacturers are listed here. Find signal generators based on the required frequency range, power level, modulation and other parameters. View product specifications, download datasheets and get quotes on parts that meet your requirement.
-
Product
RF Semi-Rigid Cable Assemblies
-
The Semi-Rigid cables are available with a copper or aluminum jacket and available with a selection of different platings and 4 different diameters (.047", .085", .141" & .250"). The Conformable®, or Hand-Formable (BJ - Braided Jacket), has a tin filled braid with a metal foil underlay and is also available in the same diameters as the Semi-Rigid type . The Flexible version, our Mini-Flex, has an FEP jacket, round braid and inner spiral shields and is available in 2 diameters, .105" &.165". All 3 types (Semi-Rigid, Conformable & Mini-Flex) are manufactured using the same type dielectric core and have virtually the same electrical performance. The decision of which cable to use should be primarily based upon your application.
-
Product
75 Ohm Mini SMB to SMZ/Type 43 Adaptor Assembly
40-978-711-0.1m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
PXI/PXIe RF Matrix, 8x4, 300 MHz, 50 Ω SMB With Loop-thru
42-729A-001-L
Matrix Switch Module
The 40-729A-001-L (PXI) and 42-729A-001-L (PXIe) are 8x4 50 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, Terminated, 8GHz, 50Ω, SMA
40-883B-002
Multiplexer Module
The 40-883B-002 (PXI) and 42-883B-002 (PXIe) are single 16 to 1 50Ω RF multiplexers with 8GHz bandwidth and automatic termination of unused signal channels. They are available in 8 to 1 and 16 to 1 configurations in two and three slots respectively.
-
Product
Compact Temperature Test Chambers
TJR
-
Specifically designed these benchtop and floor chambers to have a compact exterior yet an ample interior workspace to maximize valuable floor space. Temperature Range: -73C - 200 °C. Internal Dimensions: WxDxH (inches) 16 x 11 x 11.75.
-
Product
PXI Dual 4 to 1 RF Multiplexer 2GHz 50 Ohm SMB
40-746-511
Multiplexer Module
40-740, 40-745 and 40-746 RF Multiplexers are a range of Bi-Directional Multiplexers with bandwidth up to 2000MHz.They are arranged as Single 8 to 1, Dual 4 to 1 or Single 4 to 1 configurations, all with excellent Insertion Loss, VSWR and Isolation, in 50 Ohm or 75 Ohm versions with a wide choice of connectors.Applications include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching (from 2MBit/s to 155MBit/s), video/audio switching and switching high frequency logic signals.
-
Product
RF Connectors
HD-EFI Connectors
-
The HD-EFI product series is a micro-miniature interface designed to allow large board tolerance stack ups, blind mating, and multiple RF lines. It is available in common PCB jack and cable plug configurations, with an assortment of bullet adapters to accommodate many board to board spacing options.
-
Product
Walk-In Altitude Test Chamber
-
Guangdong Test EQ Equipment co., Ltd.
Designed to simulate and evaluate the reliability of electrical/electronic products, instruments, and industrial equipment under combined environmental stressors, this Altitude Test Chamber serves critical roles in aerospace & aviation, automotive & transportation, defense & military, energy & industrial, and electronics & telecommunication.
