ISA Backplanes
-
Product
3 PICMG® CPU, 4 PCI™, 7 ISA Slots Backplane
HPCI-13S4LU
Backplane
- Segment: 1- Slots: 3 PICMG® CPU, 4 PCI™, 7 ISA- Supports AT, ATX power supplies- Dimensions: 314.7 mm x 259 mm
-
Product
Backplanes
-
As a preferred vendor to the world''''s largest defense and industrial companies, Atrenne's high-speed backplanes are the go-to choice for organizations delivering high performance and reliability in the harshest defense and industrial computing environments. Available in all of the latest form factors, our backplanes are fully customizable to address the requirements of your specific application. Atrenne offers the industry's largest selection of 10 Gbaud Gen-3 VPX backplanes.
-
Product
Backplane Profiling & Inspection System
603d
-
A major problem in the backplane industry is detecting bent connector pin defects. The most difficult being when the pin bends underneath the shroud rather than going into the hole. Many times this defect cannot be detected electrically as the connector pin is touching the conductive annular ring of the hole, allowing electrical test to pass. Unfortunately, it is an intermittent connection and will fail later on as there is not an actual mechanical connection.
-
Product
7-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB111
-
The FAB111 has a PICMG 1.3 CPU card slot for the SHB (system host board) and offers one PCIe x16 slot, one PCIe x4 slots and four 32bit/33MHz PCI slots. Two high-speed USB 2.0 ports, a 24-pin ATX power connector and an 8-pin connector for thermal detected board are featured. The FAB110 is designed for the 8-slot industrial chassis, such as Axiomtek�s AX60551and AX60552.
-
Product
Backplane Twinax Connectors
-
We have taken the standard housing configuration of the P1 & P3 mounting dimensions while incorporating true differential pair contacts within the P1 & P3 dimensional constraints. P1 connector housing contains 21 position true differential pair blind mate contacts allowing board designers to carry high density differential pair signals from the LRU via motherboard to daughter-card plug in modules with a single connector P1 type housing.
-
Product
PICMG 1.3 Half-Size SBC Backplane
Backplane
PICMG1.3 SHB backplanes, which are compatible with half-size PICMG1.3 slot SBC. Our PCI/ISA SBC Backplane product line offers levels of mainstream and server-grade choices, supporting your rugged needs in various industrial applications.
-
Product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB119
-
*Designed for PICMG 1.3 SBC*Compatible with AX6145, AX61400, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, one PCIe x4 slots, one PCIe x16 slot, and ten 32bit/33MHz PCI slots
-
Product
3U 4-Slot OpenVPX Backplane Aligned To SOSA With 2 VITA 67.3 Aperture Slots
1SVX304AxP-xxxx
-
Designed in alignment with the SOSA, Elma's 3U 4-Slot backplanes offer 4 Plug in Card (PIC) slots to support MOSA, CMOSS and HOST initiatives. It support high-speed signals on all data paths and VITA 67.3 connectors and VITA 66.5 optical connectors.
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB109
-
The FAB109 features a PICMG 1.3 CPU card slot, one PCIe x16 slot and three PCIe x1 slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Two high speed USB 2.0 ports are featured. The FAB109 is compatible with Axiomtek's AX60501 and AX6052 chassis.
-
Product
3U 5-slots 25Gb Backplane Aligned To SOSA. AFT And VITA 48.8 Ready
1SVX306APP-1X31
-
Designed in alignment SOSA, this 3U backplane offers 5 PIC (Plug in Card) slots supporting high-speed signals on all data paths and VITA 67.3 connectors and VITA 66.5 optical connectors.
-
Product
VME Backplanes
-
VME enjoys a strong, stable ecosystem, particularly in many of the areas involving x86 compute blades, I/O, digital signal processing, and areas requiring custom design. It also enjoys some cost-effectiveness due to its wide adoption in over 400 defense programs as well as in industrial automation.
-
Product
Backplanes
-
Beijing Rdekono Electronic Equipment Co.,Ltd.
We specialize in providing durable, customizable subrack kits that ensure seamless integration with backplanes. With our commitment to quality and innovation, we deliver solutions that meet the highest industry standards for performance and reliability.
-
Product
1-Slot Power & Ground only 7U VPX backplane with aperture for VITA 67 in J3
1900002558-9001R
-
Power for 3.3V, 5V and 12V, rear connectors fully loaded. Use with Elma’s slot-to-slot or slot-to-I/O bulkhead cable products for system development.
-
Product
PXI / PXIe Backplanes
-
PXI (PCI eXtensions for Instrumentation) is a PC-based bus platform for measurement and automation systems. PXI uses commercial PC-based PCI bus technology while combining rugged CompactPCI modular packaging, as well as key timing and synchronization features. While derived from cPCI, PXI adds the timing and synchronization features, among other things, that were not present in cPCI.
-
-
Product
Digital Backplanes
MSXB 034
-
Digital Backplanes provide expansion slots to accommodate compatible digital external boards. Digital Backplanes are passive, and connect all signals in each of the expansion slots in parallel. All expansion slots are identical.
-
Product
VME / VME64x Backplanes
-
All Elma Electronic VME backplanes are designed to maximize performance, minimize noise, and to give the customer the most reliable, cost-effective product possible. The Elma Electronic VME64x backplane series is designed to fully comply with the ANSI/VITA VME extension standard.
-
Product
VME64x VITA 1.7 Backplanes
-
Atrenne VME64x VITA 1.7 backplanes comply with ANSI/VITA 5.1, include a 12-layer low noise striplinedesign with outside layers, which incorporates a chassis ground EMI shield and are available in customer configurations.
-
Product
20-slot ATX-supported Bridged PICMG Bus Active Backplane
ATX6022/20GP18
-
*1 PICMG, 18 PCI and 1 ISA*Compatible with AX61492 chassis*Supports both AT and ATX power supply
-
Product
ISA POST Code Display
post2b
-
Post2b = ISA POST code display, not RoHS compliant (can be considered test equipment, not subject to RoHS). Spec? During power on self-test (POST), most PC BIOSes will write diagnostic codes to port 80h. Use post2b to display these codes on a dual digit LED display. Additional LEDs indicate the status of the power supply rails. Convenient business card size?
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB110
-
The FAB110 offers one PCIe x16 slot, one PCIe x4 slots and two 32bit/33MHz PCI slots as well as the PICMG 1.3 slot for the SHB (system host board). The onboard 24-pi ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB110 is designed for the 6-slot industrial chassis, such as Axiomtek's AX60501 and AX6052.
-
Product
PCI Express Gen 3 Test Backplane
SKU-015-01-PCIe
-
PCI Express Backplane was designed to support a variety of modern PCI Express board’s production testing and debugging. The backplane expands the Host computer into four x16 PCI Express slots via 10 ft. CAT7 data and 10-pin flat Power control cables. PCI Express Backplane and UUTs (unit under test – add-in PCI Express board) are powered by a standard ATX power supply connected to the backplane via 24 and 8 pin power connectors located on the backplane.
-
Product
AdvancedTCA Backplanes
-
Mesh, Dual Star (5U), and 7U Pluggable Dual Star. Versions for both 19" rackmount and 23" ETSI racks are available. All Elma Electronic AdvancedTCA backplanes are compliant to the PICMG 3.0 Rev. 1.0 specifications.
-
Product
6-slot ATX-supported PICMG Bus Passive Backplane
ATX6022/6
-
*1 PICMG, 4 PCI and 2 ISA*Compatible with AX60501 and AX60530*Supports both AT and ATX power supply
-
Product
Analog Backplane Interface Board
MSXB 029
-
The Microstar Laboratories Analog Backplane Interface Board, part number MSXB 029, interfaces the Analog Backplane with a Data Acquisition Processor. The Analog Backplane Interface Board must be installed in the Analog Backplane to connect the backplane to a Data Acquisition Processor.
-
Product
5-slot ATX-supported 2U Butterfly PICMG 1.3 Bus Passive Backplane
FAB205
-
The FAB205 features a PICMG 1.3 CPU card slot, five 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. The FAB205 is optimized to support AXIOMTEK's PICMG 1.3 system host boards, the SHB100 and SHB110, which are built around the PICMG 1.3 form factor. The FAB205 is compatible with the AX61220/AX61222 chassis.
-
Product
FlexVPX Backplane
-
FlexVPX provides system designers with the flexibility and performance required for the most demanding applications. The ability to interconnect 2 and 3-slot 3U VPX compliant backplanes allows for custom system configurations using COTS hardware. Backplanes are equipped with PCI Express bridges that ensure fast and high-throughput for point-to-point communication between different elements in the system.
-
Product
3U 6-slots 25Gb Backplane Aligned To SOSA, Apertures For VITA 66/67 Modules
1SVX306AxP-xxxx
-
Designed in alignment SOSA, this 3U backplane offers 6 PIC (Plug in Card) slots supporting high-speed signals on all data paths and VITA 67.3 connectors and VITA 66.5 optical connectors.
-
Product
13-slot ATX-supported PICMG1.3 Bus Passive Backplane
FAB114
-
The FAB114 has a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three PCI Express x1 slots and a total of eight 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Through one PCIe x16 link, this PICMG 1.3 backplane maximize the performance of high-end PCI Express graphics and video cards. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB114 is perfect fit for AXIOMTEK's SHB100 and SHB110. AXIOMTEK also offers versatile 4U industrial chassis specially design for the FAB114, such as the AX61400, AX6156 series and AX61491.
-
Product
3U VPX 1 Slot P&G backplane with aperture for VITA 66.4
101V301P06-9X13
-
Power for 3.3V, 5V and 12V per VITA 46, with all rear connectors fully loaded. Use with Elma’s slot-to-slot or slot-to-I/O bulkhead cable products for system development.
