Chassis
Infrastructure housing for instrument cards typically containing a power supply, cooling fans and emi shielding.
See Also: PXI Chassis, Modular Instruments
-
Product
4U Compact 42HP CompactPCI Serial Chassis Platform
CPCIS4VC800
-
The CPCIS4VC800 is a 4U vertical-mount chassis that holdsup to eight 3U slots at a 0.8” pitch. The modular card guidescan be adjusted to allow 1.0” pitch or other spacing in .2”increments. The standard PSU is a fixed 350W ATX, but other options are available. Conduction-cooled card guides arealso available for testing and development.
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-02
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
PXI 8 Slot BRIC Solid State 288x8 1-Pole (9 sub-cards)
40-563A-121-288X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
cDAQ-9185, 4-Slot, TSN-Enabled Ethernet CompactDAQ Chassis
785064-01
Chassis
4-Slot, TSN-Enabled Ethernet CompactDAQ Chassis - The cDAQ-9185 is a CompactDAQ Ethernet chassis designed for distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. With this chassis, you can combine C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis provides precise, synchronized timing over the network using TSN, ideal for highly distributed measurements over long distances. The chassis has an integrated network switch for simple daisy-chaining. The chassis also has four 32-bit general-purpose counters/timers, accessible through a hardware-timed digital C Series module for applications that involve quadrature encoders, PWM, pulse train generation, and more.
-
Product
Type 12R2, 9U, 19" Rackmount, COTS MIL-Rugged
12R2-9U-PC
-
The 9U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock-isolated versions attenuate 25G shock to the chassis to less than 10Gs at the card cage.
-
Product
RTM ThermalBlade
-
This ATCA compatible design offers the flexibity to verify the thermal characteristics of your Advanced TCA chassis, logic cards and backplane designs. Used in conjunction with the ThermalBlade the RTM emulates a typical rear mounted logic card. Application component heights and features, airflow resistance and enclosure power dissipation can be evaluated and analyzed.Maximum sustainable watts are 113 with two switches turned on. Watts are dissipated throughout the entire RTM ThermalBlade equally.
-
Product
Full Extension Quick Disconnect Slides for 30"D Cabinets
IMS-85-C-19
-
Special order only. Friction slide yellow zinc steel slides. Ideal for mounting chassis into cabinets.
-
Product
9GS/s 16Bit 8GS Mem 4CH 8 Markers RF AWG Desktop
P9484D
Waveform Generator
The desktop version of the Proteus arbitrary waveform generator series offers up to 12 channels in a 4U, half 19” dedicated chassis. The compact form size and small footprint save valuable bench space. So for synchronized, phase coherent, multi-channel applications such as quantum physics and radar applications the Proteus arbitrary waveform transceiver is an ideal, space efficient and cost effective solution.
-
Product
PXI 4 Slot BRIC 176x4 1-Pole (4 sub-cards)
40-562A-021-176X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
High Speed Data Acquisition
-
All systems can be set up in two types of aluminum chassis. These are the conduction cooled rugged 3U VPX chassis “Crosswind 600” and “Desert Gecko” . Ruggedized and sealed to IP65. These units can use void fillers and GORE brand vents depending on the deployment environment.
-
Product
Passive Optical TAPs
SplitLight
-
Designed for networks with high fiber counts, SplitLight is a patented and customizable 1RU solution offering the industry's highest density of Passive Optical Network TAPs, WDMs, and wavelength filters in a 1RU chassis. Using this platform, service providers, data centers, large enterprises, and government agencies can now monitor more fibers, or filter and route more wavelengths, than ever before while saving valuable rack space.
-
Product
Charge-Discharge, Li-ion Cell Formation, and Test Solution
BT2200
-
The BT2200 charge-discharge platform is cost-effective and easily configurable for Li-Ion cell formation and lifetime cell cycling. A modular design supports cells requiring maximum currents ranging from ± 6 A to ± 800 A, with up to 256 cells or channels per chassis. You can quickly deploy different channel configurations as your cell requirements change and capacities grow.
-
Product
1400 Watt AC/DC Power Supply, 6U VPX
VPX56H2-6
Programmable Power Supply
The VPX56H2-6 is NAI's latest high power, High Efficiency 1,400 Watt, High Efficiency AC/DC Converter which accepts either a 3Ø 115 VAC L-N inputs or a +270 VDC input. It plugs directly into a standard 6U VPX chassis with a (VITA 62) 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
Chassis - Control Relays Greater than 8x1 or Control Multiple Relays in Series Forming Larger Switches than Normally Possible Such as 16x1 to 32x1 Sections.
CXM/256-MF
Chassis
These Chassis are typically used to control relays greater than 8x1 or control multiple relays in series forming larger switches than normally possible such as 16x1 to 32x1 sections. Or control mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 256 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional.
-
Product
Integrated 5G mmWave Test System
IQgig-5G
-
The IQgig-5G is a fully-integrated, non-signaling solution for testing 5G mmWave products at both the 28 GHz and 39 GHz frequency bands. All signal generation, analysis, and RF front-end routing hardware are self-contained inside a single chassis. The IQgig-5G is license-upgradeable to support the pre-5G and 3GPP standards evolution with up to 1 GHz of tester bandwidth. The IQgig-5G solution has three bi-directional source and measurement ports each with 2.92mm connector coaxial interface.
-
Product
PXI 8 Slot BRIC 40x32 1-Pole (8 sub-cards)
40-562A-121-40X32
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
24" Rackmount Drawer with Keylock, Unshielded, 3.5"H x 20"D
DR-032420-K
-
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
24" Rackmount Drawer, Unshielded, 3.5"H x 20"D
DR-032420-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Optical Fiber Test Platform
Fiber Lab 3200
-
Fiber Lab 3200 from M2 Optics Inc. is a must-have solution for anyone developing or testing fiber optic products and systems. Available in two types of rack-mount chassis with up to 300km per unit, it offers the most professional approach for using fiber in the laboratory or network. In addition, it provides maximum protection against potential fiber and connector damage.
-
Product
Eagle
-
Eagle is a data acquisition system designed to provide a world-class rack-mounted solution for medium channel-count dynamic data recording, and real-time monitoring requirements. Eagle is particularly suited to applications close to the test article with a rugged 19" rack-mount chassis.
-
Product
PXI Breadboard Module, 1-Slot, 37-Pin D-Type
40-220A-201
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
QorIQ P2020 Processor AMC
AMC717
-
The AMC717 is a Processor AMC (PrAMC) in a single module, mid size AdvancedMC™ (AMC) form factor based on the Freescale P2020. The module follows the AMC.1, AMC.2 and the AMC.4 specifications. The module is ideal for data flow management within a chassis. The PCIe/SRIO interface is configurable as Host or Agent mode. The PCIe option runs as x4 while the SRIO can run as x4 or dual x1. The module has option for up to 4GBytes of DDR3 memory with ECC. It provides Dual GbE to the rear per AMC.2 specification and a single GbE to the front.
-
Product
PXI 8 Slot BRIC 180x16 1-Pole (12 sub-card)
40-561A-121-180X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
+5 VDC to +3.3 VDC 75-Watt Converter 6U VME
44KS2
DC Converter
NAI’s 44KS2 is a 75-Watt DC/DC Converter that plugs directly into a standard 6U VME chassis with an 0.8” slot. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts a +5 VDC input and converts it to a single +3.3 VDC output at 75 Watts. The 44KS2 is ideal for powering single board computers or any other devices that require +3.3 VDC.
-
Product
24" Rackmount Drawer with Keylock, Unshielded, 5.25"H x 24"D
DR-052424-K
-
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
VPX Chassis 4U/42HP 5 Slots Desktop
-
This 5 slot Hartmann VPX 4U desktop system chassis provides a portable packaging solution for high-performance processors on a full mesh backplane topology. The 42HP wide desktop enclosure for vertical mounting of boards is outfitted with a 300W ATX power supply and a 1U fix bottom mounted fan tray.
-
Product
Passive Backplanes
-
Passive Backplanes series are easily customized which include PCI boards, ISA boards, PICMG 1.3 full-sized, PICMG 1.0 full-sized and half-sized single board computers. All backplane products provide with matching chassis and outstanding expansion flexibility.
-
Product
PCI Express Expansion Backplane
SKU-076-0X
-
PCI Express Expansion backplane was designed as a universal solution for Desktop or Laptop host computer expansion. It allows adding up to four additional PCI Express boards to the host computer. Expansion backplane can be placed inside any general-purpose computer chassis, and connects to the host computer via 5ft (or 10ft) CAT6 cable.
-
Product
TeraBox FPGA Servers
-
At the extreme of FPGA server density, the TeraBox 1401B/1402B give the highest level of compute and network capability in a 1U chassis. These servers provides twice the density of the typical 4U server. These innovative products support PCIe Gen4 and feature an AMD EPYC or Intel Xeon processor in a standard rack depth chassis.
-
Product
AdvancedTCA 14-Slot, 16U Chassis 40GE And 500W/slot Cooling
11A14FGBF8Y4VNXX
-
Elma’s latest ATCA chassis platform handles even the toughest cooling challenges by providing up to 500 watts per slot cooling (see simulation report). Riveted construction. Designed to meet NEBS and EMC compliance requirements.
