Data Acquisition
senses the physical, represented as an analog signal, that is then converted to digital data. Also known as: DAQ
See Also: Data Acquisition Systems, PCI Data Acquisition, DAQ, Digitizers
-
Product
CMOS/CCD Production Test System
System 1828
-
The basic system consists of a 225 MHz pattern generator, 10 clock drivers, 6 DC biases, 1-4 channels of 10 MHz 14 bit analog data acquisition and/or 1-4 channels of digital acquisition. Additional options can be added to customize the system to meet your requirements.
-
Product
PXI 2A Multiplexer, 4-Bank, 16-Channel 2-Pole
40-614-007
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
Benchtop X-ray Diffractometer
Aeris
-
Meet Aeris – our brand-new benchtop X-ray diffractometer. Aeris will impress you with data quality and speed of data acquisition so far only seen on full-power systems. The instrument is accessible for everyone with its built-in touch screen and intuitive software. Being a Malvern Panalytical product guarantees delivery of the best benchtop data and full automatability for industrial applications. Aeris is designed for low cost of ownership and is available in 4 editions tailored to the needs of specific markets: the Cement, Minerals, Metals and Research editions.
-
Product
PXI Multiplexer, Single 64-Channel, 1-Pole
40-630A-022-64/1
Multiplexer Module
The 40-630A-022-64/1 is a single 64-channel, 1-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI 2 Amp Multiplexer, Single 32-Channel, 1-Pole
40-635A-101
Multiplexer Module
The 40-635A-101 is a single 32-channel, 1-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI Very High Density Mux 49 Ch 4 Pole
40-670A-022-49/4
Multiplexer Module
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
High Range Chemiluminescence Oxides of Nitrogen Analyzer
Model T200H
-
The Model T200H combines the proven chemiluminescence principle with a number of innovative features to provide reliable and repeatable NO, NO2, and NOx measurements for extractive type CEM systems. A high-efficiency stainless steel thermal NO2 converter provides durable and consistent operation under the harshest conditions (other converter options also available).The T200H may be fitted with an optional, internal paramagnetic O2 sensor or an infrared absorption CO2 sensor, reducing integration and operating costs significantly. All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T200H comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
PXI High Density Multiplexer, 2-Bank, 32-Channel, 2-Pole
40-610A-007
Multiplexer Module
The 40-610A-007 is a 2-bank, 32-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PCI-6110, 4 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device Multifunction I/O Device
777475-01
Multifunction I/O
4 AI (12-Bit, 5 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6110 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6110 is ideal for a variety of applications, such as stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6110 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
Single 16x12 1-Pole High-Density PXI Matrix Module
40-520-101
Matrix Switch Module
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI Dual 12x8 Matrix, 2 Pole Switching
40-522-022
Matrix Switch Module
Medium density PXI dual 12x8, 2-pole matrix - it is also available in reed relay formats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
Product
High Power Narrow Linewidth Laser
AULLD series
-
Amonics' high power narrow linewidth laser (AULLD series) is integrated with Redfern Integrated Optics (RIO) PLANEXTM high performance external cavity laser. It features narrow linewidth, low phase noise, ultra low RIN, high output power with exceptionally reliable performance. The turnkey microprocessor controlled benchtop AULLD provides alarms and status indicators. An integrated RS232 or Ethernet computer interface provides easy control, diagnostic functions and data acquisition. It is particularly suitable for commercial fiber optic sensing applications, such as interferometric and Brillouin DTSS sensing systems for oil & gas, security, metrology and smart infrastructure.
-
Product
DAQ- Data Aquisition Boards
ETS Series
-
The ETS Series products are designed to create a simple "Go, NoGo" test platform that executes quickly and requires minimal Operator interaction. Low-cost alternative to traditional PC-based test equipment. Test Electronics sources and stocks a large variety of data acquisition and sensor boards to make your hardware build quick and easy. Develop your own embedded test system or use the embedded test systems we have developed.
-
-
Product
PXI High Density Multiplexer, 8-Bank, 8-Channel, 1-Pole
40-610A-009
Multiplexer Module
The 40-610A-009 is a 8-bank, 8-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
USB-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783201-01
Multifunction Reconfigurable I/O
Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7846 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
Product
Extensometers for Indirect Tensile Testing of Asphalt
Model 3911
-
Jinan Testing Equipment IE Corporation
For indirect tensile testing, such as for resilient modulus, these extensometers measure the lateral deformation of specimens. They are self-supporting on the sample and clip on in seconds. The traditional way this deformation has been measured was prone to errors caused by slight rocking of the sample as it is loaded. The self-supporting design of the Model 3911 eliminates this problem. This unit will handle the dynamic pulse requirements of resilient modulus testing.The speed of mounting makes test set-up much faster than with the older method. The pivot mounting used ensures that the specimen contact pads meet the often uneven asphalt surface as well as possible. The measuring range options available allow a wide range of testing, yet can easily measure the sometimes very small displacements required.The Model 3911 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
IRIG Time Code Receiver for Computers (PCI Express)
TCR180PEX-EL
-
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX-EL receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements).
-
Product
Ruggedized PC104+ & PCIe/104 System
Dragon
-
Excalibur’s Dragon is an advanced, ruggedized PC104 and PC104+ system in an enclosed, modular casing. The system is appropriate for use in data acquisition, recording nd control for any combination of ARINC-429, MIL-STD-1553, Serial, Discrete or similar types of communication. The modular, stack through design of the PC104/PC104+ platform allows you to build a tailor-made configuration based on Excalibur’s extensive range of boards plus any 3rd party cards of the customer’s choosing. Our engineers will integrate and test all 3rd party cards to the customer’s specification.
-
Product
Ultra-Thin Telemetry Collar
-
Advanced Telemetrics International
The Ultra-Thin Telemetry Collar houses all of the electronics needed to provide a precision radio frequency link from sensors mounted on rotating shafts to stationary data acquisition and display instruments.
-
Product
Tunable, Pulsed IR SW & LW OPO IR Source
Firefly-IR
-
Firefly IR is available in short-wave and long-wave models, providing broad wavelength coverage from 1.4-8.5 µm. The compact and sealed design requires no manual alignment, and can be used in a variety of applications in the lab and in the field. Wavelength selection and scanning is automated and performed via web browser or using a TCP/IP command set. Pulsed operation and high repetition rate provide high peak power and rapid data acquisition.
-
Product
MIL-STD-1553 A / B Test And Simulation PMC Module
PMC-1553
PMC Module
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems*Heat sink and / or protective coating available*Optional input / output for front panel
-
Product
Data Acquisition Software
TranAX 4
-
TranAX 4 is the universal data acquisition software from Elsys designed for the TPCX/TPCE data acquisition cards and the turnkey TraNET data acquisition instruments.- Measurement Configuration- Data Visualisation- Post Processing- Math. Calculation- Report Generation- Excel Export- Measurement Automation
-
Product
Powered VME64x Crates
6U VME64x 6021
-
The WIENER VME64x 6021 crate series represents a new generation integrated packaging system for 6U x 160mm VME64x/VIPA bus cards. Designed primarily for applications in data acquisition, as well as test instrumentation it combines superior mechanical quality with lowest noise power supply technology.
-
Product
Test Benches
-
Atec has made test equipment throughout all of its 65-year history. Test benches for aerospace and energy uses represent a significant segment of our experience. Atec has produced test benches involving hydraulics, mechanicals, electromechanicals, electronics, pneumatics, motors, and digital automation. Atec test benches have performed for challenging measurements, factory production, problem analysis and component overhaul scenarios. Today, complex test benches have capable data acquisition, control and communication systems integral in their electronics. Atec’s ADAQ™ system, based on COTS components and software, is proven and popular in test bench applications. DCUs, ECUs, FADECs and earlier analog or mechanical control units are easily interfaced.
-
Product
WiFiScope WS6+SureConnect: 500 MS/s 250MHz BW, 4 Channel, Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
WS6-500XMS-W5
-
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.
-
Product
Battery Testing Chambers
-
We supply a variety of test chambers for testing small battery cells to large lithium ion battery packs. Battery test chambers are supplied to a variety of industries including telecommunications, computer and automotive. With the goal of reducing automobile emissions and the development of electric vehicles, the need for lithium ion battery testing is even more critical. Our proven experience provides the most cost-effective solutions. Each test chamber is built according to specific test requirements and may be interfaced with battery cyclers, control & monitoring data acquisitions systems and other test equipment for a complete integrated test solution. All environmental chambers are designed with safety in mind. A variety of safety features are provided for reliability and abuse testing of batteries. These features may be incorporated into CSZ test chambers and tailored to the various hazard levels of EUCAR (European Council for Automotive R&D), a consortium of European car manufacturers. To better assess the hazard potential of tests, EUCAR has investigated hazardous situations and divided them into eight risk classes. The development of the safety equipment of our battery test systems is also based on this classification. For each hazard level, we recommend specific safety options that can be included with your chamber to meet your specifications to safety test your product. Together with our customers, we assess which safety devices are necessary for the respective test chambers.
-
Product
PID Testing Equipment
-
The potential induced degradation (PID) is addressed with the standard IEC TS 62804-1. The standard defines two methods that enable analyzing occurring PID effects in a specific PV module type. PSE AG offers the necessary equipment for the test in a climate chamber. The test equipment can work with any climate chamber on the market and is delivered turnkey. It comes with all necessary equipment, high voltage power sources, sensors, data acquisition and software.
-
Product
Transimpedance Amplifiers
-
Current-to-Voltage Amplifier for use with Photodiode-Based Detectors. Transimpedance Amplifiers, Standalone Devices with Data Acquisition as well as Display Function (Optometer). Log/Lin Switching Amplifiers, etc.
-
Product
PXI Very High Density Multiplexer, 99-Channel 1pole
40-670C-021-99/1
Multiplexer Module
The 40-670C-021-99/1 is a 99-channel, 1-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
