E1
European digital transmission standard that carries signals at 2 Mbps (32 channels x 64 Kbps).
See Also: HDLC, T1, E3, E1 Testers
-
Product
Eurocard Plugbord
E160-6U-1
-
VECTOR Electronics and Technology, Inc.
6U x 160mm Eurocard size for 96-pin DIN connectors. Pad-Per-Hole both sides. Voltage and ground buses around board perimeter on both sides.Pad and bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods.Row and column legends provided.
-
Product
Remote High Performance Receiver
E1709A
Receiver
The measurement signal frequency changes as the stage velocity changes. The Keysight E1709A ensures minimal phase processing errors due to frequency changes. The receiver also provides immunity to errors induced by changes in measurement signal power that occur due to small pitch, roll and yaw movements during stage motion. These features help provide the most accurate measurements under system motion.
-
Product
Sensor Cable, 5 M
E1739A
Calibration Cable
The E1739A 5-meter (16 feet) Sensor Cable is used to connect the E1736A USB Sensor Hub to either the E1737A Material Temperature Sensor or the E1738A Air Sensor. The connectors at either end of a sensor cable are identical. It is part of the 5530 Laser Calibration System.
-
Product
USB Sensor Hub
E1736A
USB HUB
Small and light weight, the Keysight E1736A USB Sensor Hub gives users the ability to connect up to four sensors to a PC. Connection from the sensors to the sensor hub is made using interchangeable cables available in 5m, 10m, 15m, and 25m lengths. Connection is made via an easy to snap in connection.
-
Product
Beam Bender BK7, Fixed Horizontal-Bend Mount
E1834M
-
The E1834M is a beam bender that bends the incoming beam at a 90-degree angle and is designed for beam diameters of 9 mm or less. This referenced optics uses high performance horizontal mount to deliver laser beam throughout a measurement system. The 8 flexure feet are designed for stable beam pointing.
-
Product
33% Beam Splitter - BK7, fixed horizontal-bend mount
E1834E
-
The E1834E is a 33% beam splitter in a high performance horizontal mount that offer the high pointing stability for Keysight laser interferometer measurement system. The 8 flexure feet are designed for stable beam pointing.
-
Product
Eurocard Plugbord
E160-3U-1
-
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Pad-Per-Hole both sides. Voltage and ground buses around board perimeter on both sides. Pad and bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods.Row and column legends provided.
-
Product
PCI/104-Express Quad PCIe MiniCard Carrier
E104-MPE
-
The PCIe MiniCard carrier provides four PCIe MiniCard sockets on a PCI/104-Express form factor board. All four sockets have PCIe x 1 and USB interfaces and support full size and half size PCIe MiniCard modules.
-
Product
Beam Bender BK7, Fixed Vertical-Bend Mount
E1834Z
-
The E1834Z is a beam bender that bends the incoming beam at a 90-degree angle and is designed for beam diameters of 9 mm or less. This referenced optics uses high performance vertical mount to deliver laser beam throughout a measurement system. The 8 flexure feet are designed for stable beam pointing.
-
Product
Eurocard Plugbord
E160-3U-2
-
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Voltage and ground buses around board perimeter on both sides. Bus surfaces solder coated for user convenience.For solder, Wire-Wrap or mixed wiring methods. Row and column legends provided.
-
Product
GaN Amplifiers
SBP-3233831838-KFKF-E1-HR
-
Model SBP-3233831838-KFKF-E1-HR is a power amplifier with a typical small signal gain of 18 dB and a nominal Psat of +38 dBm across the frequency range of 32 to 38 GHz. The DC power requirement for the amplifier is +30 VDC/2 A. The mechanical configuration is an inline structure with K(F) connector as its input port and output port. Other port configurations, such as K connectors and WR-28 waveguides for either the input or output, are also available under different model numbers.
-
Product
Eurocard Plugbord
E160-3U-3
-
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Overall ground plane both sides with 0.085" diameter clearance around each hole.. Solder coated for user convenience. Use T123 eyelets to simulate plated-thru holes committedto voltage or ground planes. Row and column legends provided.
-
Product
Eurocard Plugbord
E160-6U-2
-
VECTOR Electronics and Technology, Inc.
6U x 160mm Eurocard size for 96-pin DIN connectors.Voltage and ground bus around board perimeter on both sides. Bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods.Row and column legends provided.
-
Product
Laser and Optics Case
E1734A
-
The E1734A is a heavy duty transport and storage case which houses a basic 5530 Laser Calibration System plus additional space for other components (except tripod and rotary measurement kit). The case has integrated wheels and handle for ease of moving around. Provision for padlocks for added security is available.
-
Product
50% Beam Splitter BK7, Fixed Horizontal-Bend Mount
E1834G
-
The E1834G is a 50% beam splitter in a high performance horizontal mount that offer the high pointing stability for Keysight laser interferometer measurement system. The 8 flexure feet are designed for stable beam pointing.
