Contactors
Electro mechano connection between the DUT and ATE interface board.
-
Product
Capacitor Duty Contactor
-
ENTES Capacitor Duty Contactors are specially designed for the control of capacitors in compensation panels.
-
Product
PXI General Purpose 2A Relay Module 26xSPDT
40-131-201
Relay
These are low cost, general purpose electromechanical relay cards capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
Product
PXI 16xSPST 16A Power EMR Module
40-161-001
Relay
These Power Relay Modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. The 40-161 is ideal for switching up to 16A in both AC and DC applications.
-
Product
PXI Single 8x2 1-Pole 10A Power Matrix
40-551-002
Matrix Switch Module
Used for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. X and Y connections are made via a 20-way GMCT plug, the 8x4 module with loop-thru has an additional 20-way GMCT plug for module-to-module connection. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. Suitable for applications requiring switching of either mains voltage or direct current.
-
Product
Kelvin Test Contactor
cCruiser
-
cCruiser™ Kelvin contactor was designed with cost of test optimization in mind, boasting a cantilever design that allows the testing of challenging discrete ICs and small logic package types. Providing a best-in-class proven lifespan of up to 5 million touchdowns increasing handler uptime. cCruiser reduces the cost of test for customers significantly, lasting longer and testing longer than previous contact solutions.
-
Product
Full Wafer Contact Test System
Fox 1
-
Unique cartridge technology uses full-wafer contactors combined with parallel test electronics to achieve single touch, full-wafer test
-
Product
PXI 5A Power MUX, 1-Bank, 48-Channel
40-651-001
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel 4-bank. 11-channel 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
Single 4x4 1-Pole 16 Amp PXI Power Matrix
40-552-001
Matrix Switch Module
The 40-552 range of 16 Amp PXI power matrix modules is available in four configurations with matrix sizes of 8x2 and 4x4 and the ability to expand the matrix size with the Y-Axis loop-thru connections: e.g. 8x4, 12x4, 16x4, etc. (with 4x4 matrices) or 16x2, 24x2, 32x2, etc. (with 8x2 matrices). This range is capable of switching up to 16 Amps and up to 300VDC/250VAC hot switching and 400VDC/250VAC cold switching. These PXI power matrix modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors, and solenoids.
-
Product
Custom Test Fixtures
-
For popular high speed components like semiconductor packages, and test contactors, we have developed a custom test fixture which allows the use of high bandwidth microprobes to measure virtually any I/O pin, according to GigaTest's methodology and requirements.
-
Product
PXI 40Amp 14Volt 4xSPST Automotive Relay
40-180-101
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC. The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
Switched Power Distributed Module, CAN Control
H730008xS
Power Module
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions: Distributing the power to each device in a system Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.
-
Product
8x4 Power Matrix, 2-Pole, 2xGMCT
40-550-902
Matrix Switch Module
This version of the 8x4 power matrix is for heavy current/low duty cycle power switching. Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current.
-
Product
Test Contactor
RF Scrub
-
RF Scrub™ Test Contactor’s innovative design combines an extremely short signal path (0.90mm test height) with high wear resistance pins that can operate in a wide temperature range.The RF Scrub Test Contactor’s long-life, elastomer free design and easy field maintainability makes it an optimal solution for testing of high-performance devices.The RF Scrub design minimizes load board wear and with the unique pin base material and plating, the cleaning intervals can last up to 100,000 cycles.
-
Product
PXI General Purpose 2A Relay Module 16xSPDT, 78 D-sub
40-131-101
Relay
Low cost, general purpose electromechanical relay cards suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include switching of medium power AC and DC loads or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 50 or 78 pin D-Type connector plug.
-
Product
Capacitor Contactor
KML
-
Lifasa - International Capacitors, SA
The new KML contactors are designed in accordance with IEC 60947-1 and are suitable for the connection of three-phase power capacitors. Thanks to its pre-load block mounted on the same contactor, the strong current tips produced at the moment of capacitor connection are reduced and the contactor itself is protected at the same time.
-
Product
PXI Single 16x4 1-Pole 5A Power Matrix
40-549-001
Matrix Switch Module
The 40-549 is a single pole power matrix module, suitable for switching inductive/capacitive loads up to 5A with 110VDC/250VAC hot switching and 400VDC/250VAC cold switching. It is available in single 16x4, single 8x8, dual 8x4 or single 8x4 configurations. Connections are made via a front panel 25 way D-type male connector. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. The module is suitable for applications requiring switching of either mains voltage or DC current.
-
Product
Process Ozone Monitor
Model 465M
-
Teledyne Advanced Pollution Instrumentation
The Model 465M is a microprocessor based medium range ozone monitor for measuring process ozone concentrations in water treatment, food processing, and research applications. The design has been specifically optimized for applications requiring the measurement of ozone at near-ambient pressure such as water treatment contactor off-gas measurement. The Model 465M has been designed to give accurate and stable readings over long time periods with little or no maintenance or calibration. The Model 465M is available in a NEMA 4X wall mount enclosure.
-
Product
PFR96
2WE06
-
The digital controller PFR96 can manage up to 12 independent batteries, a communications port, and two current inputs in size from 96×96 framework. Particularly easy to program thanks to a basic configuration with two parameters and advanced that allows the advanced user the most complete of the power factor correction control.The onboard logic allows corregegre setup via an erroneous wiring of the picture as to or stage of TA.10ms sampling of the voltage allows the calculation of the RMS voltage continuously, identifying network holes and temporary interruptions and detach the active steps immediately to the protection of the contactors and benches.The PFR96 can handle numerous alarms associated to available relays.The means of intervention in the PFR96 adjustment are all customizable for a better quality of the intervention as well as the use of different banks can be equalized for less wear of the contactors.Sampling at variable frequency and RS485 communication for remote control (PFR96 Plus) complete a range of services offering maximum control and quality of the measurement
-
Product
Test Contactor
cGator
-
cGator™ singulated power contactor is a top and bottom contacting solution for power Known Good Dies (KGD).Cohu´s patent pending Volta-Flux™ MEMS probe architecture technology provides stable and low CRES for very challenging high-voltage and high-current requirements.The gentle-touch feature reduces surface impacts to a minimum while providing a reliable contact force.
-
Product
PXI 8x4 1-Pole 10A Matrix With Loop-Thru
40-551-101
Matrix Switch Module
Used for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. X and Y connections are made via a 20-way GMCT plug, this module with loop-thru has an additional 20-way GMCT plug for module-to-module connection. This version of the 40-551 may be expanded to larger matrix sizes using cabling to daisy-chain the X and Y signals Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. Suitable for applications requiring switching of either mains voltage or direct current.
-
Product
Single 16-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-003
Multiplexer Module
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
High Performance Chipscale Test Sockets
SC
-
Ardent Concepts Test Sockets for ATE test deploy patented SC Contact Sets. This technology is capable of over 2 Million mechanical insertions in production environments and uses easy to replace pins with no complicated assembly procedure. It is designed to be drop-in compatible with 1mm offset and straight through footprints to ease implementation, and RC SC’s simple and robust design is extremely cost effective when compared with existing “roll” type test contactors and sockets. Designed specifically for JEDEC QFN and MLF applications, SC High Performance Test Sockets are available for most handler set-ups and offer exceptional AC performance.
-
Product
PXI 18 Channel Power Mux 1 Pole
40-665-001
Multiplexer Module
Model 40-660 is a 10-Channel Power Multiplexer, suitable for switching inductive/capacitive loads up to 10A at 250VAC. It is available with a choice of 1-pole (10A) or 2-pole (8A versions). Model 40-665 is a higher density 18 Channel Power Multiplexer with the same specification as the 40-660. Power Multiplexer Modules are intended for switching heavy AC or DC loads or for slave switching large external relays, contactors and solenoids.
-
Product
PXI 8 x DPDT Power Relay Module, 5A
40-157-001
Relay
40-150/151 modules have 8xDPST or 12xDPST power relays, suitable for switching inductive/capacitive loads up to 5A at 250VAC. 40-155/156 modules have 8xSPDT or 16xSPDT power relays and 40-157 is configured as 8xDPDT. Power relay modules are intended for switching heavy AC or DC loads or for slave switching large external relays, contactors and solenoids. The 40-150 series of power relay module are suitable for applications requiring switching of either mains voltage or DC current.
-
Product
Slip-Ring Motor Starting Panels
Rotor Starter
-
The Slip-Ring Motor Starters are based on the series of resistors that are applied to the rotor circuit to control the speed/torque characteristics of the motor. Rotor starters are mainly used for the motor starting applications requiring high-starting torque like loaded belt conveyors in mining industry. By external resistors, it is possible to shift the motor maximum (break-down) torque up to starting torque point for motors under heavy loads during start-up. The resistors are splitted into some steps and controlled via contactors by motor starting control system. As the motor speed increases, the external rotor resistors are eliminated by shorting contactors until all external resistors are shorted out.
-
Product
Almanac Time Switch
IM1754
-
Almanac Tme Switch is a real time timer which can be used to switch electrical appliances like street lamps, garden lights, corridor lights, neon signs etc. as per time of the day. The timer has built in Almanac timings fixed in Nonvolatile RAM so that the user does not have to programme the unit from time to time. This Almanac time switch has added advantage over daily dial or weekly timers. Timer provides two outputs to drive contactors of different ratings. These outputs can be used with different combinations to achieve desired output. Timer is provided with manual override facility. Optional detachable external keyboard unit provided to avoid unauthorized access.
-
Product
Kelvin Test Contactor
nano
-
nano Kelvin™ test contactor is a well-established Cantilever Kelvin test contactor with proven performance in the automotive market and further increasing popularity due to the robustness and reliability of the product.Featuring a small imprint area, contact motion decoupled from the test board and simple and cost-efficient test boards.
-
Product
Pick And Place Contactors
-
Designs available for all Pick and Place handler brands, suitable for all range of packages with Multiple Pitch and various numbers of I/Os. Full tri-temp capability up to 180 Deg C.
-
Product
Automotive Contactor
Pad Series
-
Johnstech International Corporation
Automotive Contactor is just the product you’re looking for! This Xtreme Temperature (XT™) capable product is designed to maximize your test results, regardless of your tri-temp testing objectives! Even if you are not testing outside the temperature limits of standard Contactors and sockets, the robust design of the XT™ Contactor provides additional design margin and certainly satisfies even your roadmap requirements.
-
Product
Test Contactor/Probe Head
Mercury
-
Mercury™ test probes and contactors are excellent spring probes for the laboratory though they were designed with the robust qualities needed for high-volume production test. Their unique design ensures excellent plating quality for low, consistent resistance, long life, and high-test yields.Mercury probes are available with minimum pitches of 0.3 mm, 0.4 mm, 0.5 mm, and 0.8 mm, to provide the best performance at any device pitch. Mercury probes have bandwidths of up to 22 GHz, and can carry over 3 Amps of current. The Mercury is an excellent choice for any test application.
