PXI
PXI or PCI Extensions for Instrumentation is a bus standard for high performance measurement and automation. Also known as: PCI Extensions
See Also: Instrument Control Buses, Modular Instruments, PXIe, LXI, AXIe, PCIe, GPIB, USB, PCI, Ethernet, LAN, VXI, CompactPCI
-
Product
PXI Optical Extenders for Instrumentation
-
The Keysight Optical Extenders for Instrumentation offers capability that is modular, scalable, and upgradable to meet the challenging demands of applications requiring long distance RF paths. Configure a single link, extend the port of your PNA, or design a system that includes remote operation of the measurements while achieving an RF signal path over distances that have been impossible until now.
-
Product
PXIe-8881, 3.9 GHz 8-Core PXI Controller
786636-01
Controller
PXIe, 3.9 GHz 8-Core PXI Controller - The PXIe-8881 is an Intel Xeon 8-Core embedded controller for PXI Express systems. You use the PXIe-8881 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8881 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive and other peripheral I/O, such as two Thunderbolt 3 ports. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-051-HI
Programmable Resistor Module
The 40-230-051-HI (PXI) and 42-230-051-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 2.95MΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 8 Slot BRIC 60x16 1-Pole (4 sub-cards)
40-561A-121-60X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8x4 Power Matrix, 2 Pole
40-550-002
Matrix Switch Module
Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current. These modules are fitted with electro-mechanical power relays, gold-flash over silver alloy. A spare relay is built onto the circuit board to facilitate easy maintenance with minimum downtime.
-
Product
AIT PXI Express Test & Simulation Instruments
-
Avionics Interface Technologies
AIT’s Test & Simulation Instruments for MIL-STD-1553, ARINC 429, ARINC 664/Avionics Ethernet, and Fibre Channel are available in PXI and PXI Express form factors and are supported by software drivers for Windows, Linux, and LabVIEW Real Time. All instruments are also supported by Software Development Kits which provide API’s for C/C++, C#, and LabVIEW.
-
Product
BRIC™ - Large PXI Matrix Modules
-
High Density Packaging and Integrated BackplanesWith Pickering's BRIC Large PXI Matrix Modules, the use of high density packaging and integrated backplanes enables a large matrix to be implemented with no user configuration or special matrix expansion kits. These matrices use thru-hole mechanical relays (not surface mount) and can be serviced using standard de-soldering tools simplifying repair and reducing down time. Our BRIC's integrated design ensures high matrix performance with high signal bandwidth and fewer system implementation errors.
-
Product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Single-Mode
40-855A-312
Multiplexer Module
The 40/42-855A-312 is a PXI/PXIe 2-channel multiplexer with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PXI 4-Slot BRIC Matrix, 276x4, 1-Pole (3 sub-cards)
40-560B-021-276X4
Matrix Switch Module
The 40-560B-021-276x4 is an ultra high density matrix module and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 8x4 RF Matrix 100MHz 75 SMB
40-729-101
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI 8-Slot BRIC Matrix, 308x4 2-Pole (7 sub-cards)
40-562B-122-308X4
Matrix Switch Module
The 40-562B-122-308X4 is a high density BRIC8 matrix module with a size of 308x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Remote Control Interface Module
41-924-001
Remote Control Interface
Part of the PCIe to PXI Remote Control Interface Kit. The kit provides a seamless connection between a PC’s PCIe slot and a PXI chassis and is suitable for providing an interface to any PXI chassis.
-
Product
PXI Dual 3-Channel 30A Solid State MUX
40-667-011
Multiplexer Module
The 40-667 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.Each multiplexer channel can support 30A of continuous current and switch up to 40V signals. The switches can sustain inrush currents in excess of 120A. AC or DC signals can be switched since the switch is polarity insensitive.Note: The 40-666-011 supersedes the 40-666-001 which is functionally the same but with some changes in specification. A data sheet for the 40-666-001 can be found in the 40-666/667 User Manual.
-
Product
PXI Pull-Thru Adapter, Wired, Excalibur EXC-4000cPCI/xx
510140129
Pull-Thru Adapter
PXI Pull-Thru Adapter, Wired, Excalibur EXC-4000cPCI/xx
-
Product
PXI 12-Slot BRIC Matrix, 121x16 1-Pole (11 sub-cards)
40-562B-321-121X16
Matrix Switch Module
The 40-562B-321-121X16 is a high density BRIC12 matrix module with a size of 121x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Dual 8 to 1 RF MUX MCX 75 Ohm
40-834-102
Multiplexer Module
The 40-834-102 is a 75 Ohm 8 to 1 RF MUX with 2 banks in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40-834 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 4-Channel, 2-Pole
42-739-006
Multiplexer Module
The 40-739-006 (PXI) and 42-739-006 (PXIe) are dual 4-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber
40-852A-118-M50-HI
Multiplexer Module
The 40/42-852A-118-M50 is a PXI/PXIe 8-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
PXI Chassis, 8-Slot
40-924-001
Chassis
The 40-924 includes all the features and performance required by the PXI standard and supports a control interface or embedded controller and up to 7 additional 3U peripheral modules.
-
Product
PXI-7954, Virtex-5 LX110 FPGA, 128 MB DRAM PXI FPGA Module for FlexRIO
780563-01
FPGA Module
Virtex-5 LX110 FPGA, 128 MB DRAM PXI FPGA Module for FlexRIO—The PXI‑7954 provides flexible, customizable I/O for LabVIEW FPGA. It includes 132 single-ended I/O lines configurable as 66 differential pairs. You can pair the PXI‑7954 with FlexRIO adapter modules that offer high-performance analog and digital I/O. Together, the two modules create a reconfigurable instrument that you can program with LabVIEW FPGA software.
-
Product
PXI 2-Slot BRIC Matrix, 126x12, 1 Pole (3 Sub-cards)
40-558-201-126x12
Matrix Switch Module
The 40-558-201-126x12 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI/PXIe High Voltage Multiplexer, Single 48-Channel, 2-Pole
40-321-129-HI
Multiplexer Module
The 40-321-129-HI (PXI) and 42-321-129-HI (PXIe) are single 48-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXIe-5110, 100 MHz, 1 GS/s, 8-Bit PXI Oscilloscope
785767-01
Oscilloscope
PXIe, 100 MHz, 1 GS/s, 8-Bit PXI Oscilloscope—The PXIe-5110 oscilloscope has two channels that sample up to 1 GS/s with flexible and programmable settings for coupling, input impedance, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that facilitates high-speed data throughput and includes analysis functions. This device is ideal for automated and partially automated applications that require flexible measurement configurations and up to 100 MHz of analog bandwidth. The PXIe-5110 also features advanced PXI synchronization and data throughput capabilities. Some options also support CableSense™ technology, which can detect and locate signal path faults, changes, or discontinuities.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-033
Precision Resistor Module
The 40-297A-033 (PXI) and the 42-297A-033 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 52.4 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Fixed Wavelength CW Laser Source (FP) - PXI
Laser 1100 Series
Laser Source
The Laser-1102 is a Continuous Wave (CW) laser source offering high power 850 nm output into multimode fiber with stable output power operation.
-
Product
PXI/PXIe High Voltage Multiplexer, Dual 23-Channel, 2-Pole
42-321-128-HI
Multiplexer Module
The 40-321-128-HI (PXI) and 42-321-128-HI (PXIe) are dual 23-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI/PXIe Microwave Relay, Quad SPDT, 2.5 GHz, 75 Ω, 1.6/5.6, Failsafe
42-780B-754
Relay
The 40-780B-754 (PXI) and 42-780B-754 (PXIe) are quad failsafe SPDT 2.5 GHz 75 Ω unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
PXIe-8280, 1-Port, 50 Gigabit, RDMA PXI Ethernet Interface Module
788261-01
Ethernet Interface
The PXIe-8280 is a high-performance 50-Gigabit remote direct memory access (RDMA) interface for PXI Express. This module includes one 50-Gigabit Ethernet QSFP28 port in a single-slot PXI Express module and supports RDMA over Converged Ethernet (RoCE).
-
Product
PXIe-4330, 25 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module
781346-01
Analog Input Module
25 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module—The PXIe‑4330 is a simultaneous input module that provides integrated data acquisition and signal conditioning for bridge-based sensors. The PXIe‑4330 includes increased accuracy, high data throughput, and synchronization features, making it ideal for high-density measurement systems. To remove noise, the PXIe‑4330 offers antialiasing and digital filters per channel. Each channel also features an independent, programmable excitation voltage. Additionally, the PXIe‑4330 provides remote sensing, internal bridge completion, and shunt calibration options per channel.
-
Product
PXI 16x4 Signal Insertion and Monitor Matrix
40-525A-002
Matrix Switch Module
This is a PXI signal insertion and monitor matrix with switched pass thru connections on both X and Y axis. It is also available in a 34x4 format and can be used for signal insertion and monitoring purposes on connections between the UUT and test system.
