I²C
A slow Inter-Integrated Circuit bus protocol.
-
product
C Series Voltage And Current Input Module
The C Series Voltage and Current Input Module features up to 16 input channels with built-in noise rejection. You can use this module to combine the two most common inputs to reduce the overall number of modules you need in your measurement system.The C Series Voltage and Current Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
NI-9221, ±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module
783732-01
±60 V, 800 kS/s, 12-Bit, 8-Channel C Series Voltage Input Module - The NI‑9221 performs single-ended analog input. The wider voltage range makes this module well suited for industrial-level, automotive, or even smaller-cell battery measurements. There are two connector options for the NI‑9221: a 36‑position spring‑terminal connector and a 37-position D‑SUB connector.
-
product
SparkFun IR Array Breakout
110 Degree FOV, MLX90640 (Qwiic)
It's time to say hip hip array for this IR Breakout! The MLX90640 SparkFun IR Array Breakout is equipped with a 32x24 array of thermopile sensors creating, in essence, a low resolution thermal imaging camera. With this breakout you can detect surface temperatures from many feet away with an accuracy of ±1.5°C (best case). To make it even easier to get your low-resolution infrared image, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
Rapid-Rate Cycling Chambers
TCC
Through simulation of wind volume and wind speed, TCC-150 can minimize specimen temperature variations, enabling more accurate quick temperature change testing. For specimen temperature, the ramp rate is 15°C/min. For air temperature,the ramp rate is 23°C /min (temperature heat-up average).
-
product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m, HV
A037DF4-C-HA050
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
3U CompactPCI Serial 2-Port CAN From PEAK Module
cPCI-A3CAN
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP- 2x D-Sub CAN ports in front panel- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
product
Hazardous Location Syringe Pump
260HLf
Teledyne LABS HLf-Series pumps give you the same accurate, predictable flow and pressure control as our standard D-Series, while conforming to safety standards for use in UL Class I, Division 2, Groups A B C & D, T4 environments. The hazardous location rating is achieved through internal design modifications including the use of brushless DC motors. This approach eliminates the need for purge boxes or other additional safety devices. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases, viscous fluids, or slurries and pastes. If needed, optional materials such as Hastelloy C-276 are available on request. The HLf controller has a keypad and LCD, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly.
-
product
Radar solution for thickness measurememt of steel & metal
Our radar sensor solution determines the thickness and the thickness profile of steel plates, steel strips or steel slabs (up to 1600 °C hot) with an accuracy of up to ±10 µm on the roller conveyor. Thanks to robust radar technology, sophisticated signal processing and intelligent radar algorithms, OndoSense radar sensors achieve this high level of precision in thickness measurement even under the difficult production conditions of the steel industry with smoke, steam, dirt, vibrations, fire and extreme temperatures.
-
product
Tool
Imagix 4D
Imagix 4D is a tool to understand, document and improve complex, third party or legacy source code in C, C++ and Java. Imagix 4D automates the analysis of control flow and dependencies. It detects problems in data usage and task interactions. With Imagix 4D you increase productivity, improve quality, and reduce risk.
-
product
Bypass Diode Thermal Test System
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
product
Total Organic Carbon Analyzer
TOC-L Series
The TOC-L series of TOC analyzers adopts the 680°C combustion catalytic oxidation method, which was developed by Shimadzu and is now used worldwide. While providing an ultra wide range of 4 μg/L to 30,000 mg/L, these analyzers boast a detection limit of 4 μg/L through coordination with NDIR. This is the highest level of detection sensitivity available with the combustion catalytic oxidation method. In addition, the combustion catalytic oxidation method makes it possible to efficiently oxidize not only easily-decomposed, low-molecular-weight organic compounds, but also hard-to-decompose insoluble and macromolecular organic compounds.
-
product
High Power Digital Lab Series Regulated DC Power Supply – 3000W
- 3000W different combination- High current density.- 19″ rack adaptable -5U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation Optional, at extra cost- Over voltage protection- 19″ rack mounting
-
product
High Temperature XY Planar Biaxial Extensometer 1200 C or 1600 C)
Model 7651
Jinan Testing Equipment IE Corporation
Model 7651 extensometers measure combined in-plane strains in flat cruciform specimens tested in machines capable of simultaneous X and Y (perpendicular) axial loading and on standard flat samples tested in pure tension. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7651 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to eliminate crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃(2900°F) high temperature option.
-
product
NI-9423, 24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module
783735-01
24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9423 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels, can accept up to … 30 V discrete logic levels, and has an LED that indicates the status. The NI‑9423 offers isolation between the input and output banks from channel to earth ground. The NI‑9423 is a correlated digital module, so it can perform correlated measurements, triggering, and sychronization when installed in a CompactDAQ chassis.
-
product
Semiconductors Testing
Our Testers support the production lines of variety of products such as 40/100 GBps Mux/DeMux, LNA, WiMAX RF Transceivers, Microwave & Millimeter Wave components. This high reliability products are being used in (a) Networking & Communications (b) Consumer Electronics (c) Military & Space
-
product
DC/AC Inverter 450 W
ODS-750-7273
DC/AC inverter with 750 W from Premium | input ranges 16.8 - 30 VDC | output 230 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke
-
product
A C & D C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
AV/DV-50VA-10V
A C & D C DIELECTRIC STRENGTH TESTERS ( HIPOTS )
-
product
Simulink models run on ADwin
ADsim
With ADsim, you easily run Simulink models on ADwin hardware. With a few clicks only, you insert inputs and outputs for the ADwin system as blocks into the model and start C code generation. After compilation, the model runs on the ADwin system in real-time with absolute timing precision and predictability reaching sample rates up to 100 kHz.
-
product
Erbium Doped Fiber Amplifier
EDFA
EDFAs are based on the light amplification in erbium-doped fiber, which are optically pumped by means of 980 nm or 1480 nm light sources. In this way, the light of a larger wavelength within the C or L band applied to the input of the amplifier is amplified, thus widening the range of optical communication links. EDFAs typically operate in saturation and the average signal power determines the average gain. The dynamics of EDFA are unaffected by the sequence and dynamics of a digital signal or channel interaction in DWDM systems. As a result, multiple channels can be bundled within the total erbium spectral amplification bandwidth. However, the total average output power in both cases is determined by the saturation power of the specific EDFA.
-
product
NI-9247, 50 kS/s/ch, 50 Arms, 147 Apk, 24-Bit, 3-Channel C Series Current Input Module
783589-01
50 kS/s/ch, 50 Arms, 147 Apk, 24-Bit, 3-Channel C Series Current Input Module - The NI‑9247 is designed to support direct ring lug connectivity to the three-phase high-current measurements of 1 A and 5 A current transformers (CTs). It is optimized for power, energy, and industrial applications. The safety features, certifications, input ranges, overvoltage ranges, and connectivity are well suited for applications such as power quality monitoring and metering, utility pole-mounted smart switches, utility pole-mounted smart grid reclosers, substation merging units, industrial machine measurements, health monitoring, predictive maintenance and prognostics, and phasor measurement units (PMUs).
-
product
General Purpose Switching PXI Card
GX6325
The GX6325 is 6U switching card with 75 SPDT Form C relays with a switching power rating of 60 W. Featuring the highest density available in PXI for this type of switch card, the GX6325 is suitable for all test applications requiring general purpose, low level switching.
-
product
Emulates AT8xC5122 Derivatives with 6/12 Clocks/Cycle
FE-5122
* Emulates AT8xC5122 Derivatives with 6/12 Clocks/Cycle * 32K Code Memory * Software Trace * Real-Time Emulation * Frequency up to 40MHz * MS-Windows Debugger for C and Assembler * Keil Vision2 Debugger Compatible * PLCC-68, PLCC-28, LQFP-32 and VQFP-64 Emulation Headers * Serially Linked to PC at 115Kbaud
-
product
NI-9222 , ±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
781397-01
±10 V, 500 kS/s/ch, 16-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9222 performs differential analog input. This module is well suited for applications such as ballistics, impact, and blast wave testing. The NI‑9222 can sample at the maximum sample rate per channel while the module next to it samples at a much slower rate, which is ideal for mixed-measurement test systems. There are two connector options for the NI‑9222: a 10‑position screw terminal or a 25‑pin D‑SUB connector.
-
product
Electronic DC Load, 500V, 16A, 400W
LDH400 Series
Versatile solution for direct testing of dc power sources and PFCsConstant current, resistance, conductance and power modesWide voltage and current range, 10 to 500V and 0 to 16A400 watts continuous dissipation at 28°C (360W at 40°C)High resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminalsLoad inputs rated to CAT II (300V)Full bus control via USB, RS232 and LXI compliant LAN interfacesGPIB Option
-
product
Powered VME Crates
VME is a high speed and high performance bus system with powerful interrupt management and multiprocessor capability. It was created by combining VERSAbus electrical specifications (1979) with the Eurocard format resulting in the VMEbus Revision A - 1981 specification. The VMEbus specification has since then been refined through revisons B (1982), C, C.1, IEC 821 & IEC297 and IEEE 1014-1987.
-
product
10W to 30W - Single Output
ZWS-B Series
*Operating temp -10°C to +70°C*Low off-load power draw (<0.5W)*10 Year e-cap Lifetime*Universal Input (85 - 265VAC)*Suitable for 'Green' products*Five year warranty
-
product
Digital Sound Level Meter
Model KM 926
Kusam Electrical Industries Limited
• KM 926 designed according to the IEC 651 TYPE 2 & ANSIS1.4 TYPE 2 for sound level meter.• Instantaneous sound measure function.• Measurement Range : 30 ~ 130decibel• With two equivalent weighed sound pressure levels, A & C.• Fast & Slow dynamic characteristic modes.• AC & DC signed output for frequency analyzer level recorder, FFT analyzer, graphic recorder etc.
-
product
NI-9229, ±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Module
780180-01
±60 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Module - The NI‑9229 performs differential analog input. The NI‑9229 is an effective general-purpose analog module because of its resolution, sample rate, and input range. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating.
-
product
NI-9234, 4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module
779680-03
4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module - The NI‑9234 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9234 is also compatible with smart TEDS sensors. The NI‑9234 delivers a wide dynamic range and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
product
NI-9224, ±10 V, 1 kS/s/ch, 24-Bit, Simultaneous Input, 8-Channel C Series Voltage Input Module
783862-01
±10 V, 1 kS/s/ch, 24-Bit, Simultaneous Input, 8-Channel C Series Voltage Input Module - The NI‑9224 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. The NI‑9224 is simultaneous sampling with two options for filtering a low-latency filter or a 50/60 Hz rejection filter. The low-latency filter enables users to use this module in industrial or control applications while getting better external noise rejection.
