-
Product
High and Low Temperature Humidity Chamber
GDJS/GDJW
-
•The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip. •The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1℃ and humidity is 0.1%R.H •The temperature sensor is platinum PT100 Ohms/MV resistor •The heating system is full separately system which produced by Nickel chromium alloy electric heating type heater •The cold system is applied by fully enclosed fan cooled single-stage and cascade refrigeration mode, the compressor is from France TECUMSEH brand which can allow you get after sales support from many countries •The cyclical system is applied by High temperature low noise air conditioning type motor and Multi blade centrifugal wind wheel •The safety self-protection function include Electric leakage, short circuit, over temperature, motor overheating, compressor pressure, overload, over-current protection •Working Power: AC380V±10% 3phases and frequency 50Hz/60Hz •Working Environmental: Temperature is 5℃～+30℃ Humidity ≤85%R.H
-
Product
200KHz AUTOMATIC TRANSFORMER TEST SYSTEM
VE2729XAU
-
Its a Microprocessor Based 200KHz Automatic Transformer Tester with inbuilt 20 Pin Channel Scanner for Automatic Switching and Testing Coils & Transformers (Ferrite) with Max. 20 PINS. Test Parameters : -> Inductance (L)-> Leakage Inductance (Lk)-> Capacitance (C)-> DC Resistance (Rdc)-> AC Resistance (Rac)-> Turns Ratio with Winding Polaity-> Quality Factor (Q)-> Impedance (Z)
-
Product
Strain Measurements and Experimental Stress Analysis
-
Experimental structural testing using strain gauges is necessary in a wide range of applications from airframes and sub-assemblies down to individual components such as turbine blades, satellites, wind turbines, buildings, bridges and many others. These tests enable the engineers to compare the acquired data with the predicted results from the design calculations.
-
Product
IoT Gateway
-
ADLINK embedded IoT gateway platforms fully support Intel® Gateway Solutions for Internet of Things (IoT) by integrating Wind River Intelligent Device Platform* (IDP) XT and McAfee* Embedded Control to provide a complete, pre-validated communication and security solution. But also includes ADLINK’s SEMA utility, which enables quick setup of remote data access and analysis through ADLINK's SEMA Cloud.
-
Product
Wind Direction Sensor
ENVIROMUX-EWDS
-
Balanced wind direction vane with a near-zero friction bearing and a high accuracy magnetic angle sensor to provide precision wind direction. Sensor range: full 360 degrees , zero deadband. Accuracy: ±1.8 degrees. Resolution: 12 bit or 0.025 degrees. Directional Vane approximately 8 inches (203 millimeters). 3 wire flying leads, 25-feet (7.6-meter). Supply voltage: 4.5 to 5.5 VDC. Current: 15 mA typical. Output: 5 to 95% of input voltage (0.25 to 4.75VDC). Requires the ENVIROMUX-S5VDC-5V to operate with ENVIROMUX-2D/5D/16D. Maximum cable length: 1000 ft (305m)
-
Product
Millohm & LCR
-
Help prevent failures in motor windings, generators and transformers with a quick and easy resistance test using an Amprobe milliohm meter. To efficiently inspect and verify electronic components for quality control, choose an Amprobe LCR tester.
-
Product
Air Flow Meters
-
An Air Flow Meter measures air velocity as well as air pressure. Depending on the type of application, the Air Flow Meter is made as a hot-wire Air Flow Meter, a vane Air Flow Meter, a cup anemometer, a Pitot tube air flow meter or a pocket weather flow meter, all of which can measure air velocity as well as air pressure. Some can even detect the wind direction. The most common unit of measurement for air flow is m/s.Air Flow Meters are basically mass flow meters, as they determine the air velocity and air pressure by measuring the mass flow of a medium, which is air in this case.The results of measuring the air velocity can be stored in the Air Flow Meter's memory, depending on the model. There are a lot of Air Flow Meters available. The air flow meter is ideal for taking quick or constant measurements including monitoring of ventilation installations, process checking, industrial applications, use in private workshops or by nautical enthusiasts or for other hobbies, etc.At PCE, you can find the right air flow meter to use indoors and outdoors. An optional ISO calibration certificate is available for many of the devices.
-
Product
Coating Thickness gauges.
-
PELT gauges provide data for the precise control of exacting coating-applications including for automotive paints, wind turbine blade protective coatings, steel coil coatings, and shipping container anti-corrosion coatings. PELT gauges measure coatings on substrates including steel, aluminum, plastics, carbon fiber, composites, glass, and wood.
-
Product
Transformer Winding Resistance Meters
RMO TT Series
-
The Tap Changer Analyzer & Winding Ohmmeter of the RMO-TT series is designed for winding resistance measurement of inductive objects, and for a tap changer analysis. The RMO-TT series is based on the state of the art technology, using the most advanced switch mode technology available today. The RMO-TT instruments are accurate (0,1%), powerful (up to 100 A) and still portable. The Instruments generate a true DC ripple free current with automatically regulated measurement and discharging circuit. RMO-TT instruments can perform a simple, quick and reliable transformer on-load tap changer condition assessment. This series of instruments enable measurements of a winding resistance in every tap position, current ripple values (percentage of a current drop during a tap change) and transition times during the tap changes. Problems with a connection, contacts, and selector/diverter switch operation (tap change with interruption) can be detected with these measurements.
-
Product
Dual-Channel Precision Audio Analyzer with Built-In Condenser Measurement Mics
PAA6
-
Essential tools, such as the Phonic PAA6 Professional Audio Assistant generally wind up at the bottom of pro audio wishlists after esoteric preamps, compressors, and EQs. But more often than not, the key to great sound lies in the utilitarian gear, particularly, the Phonic PAA6 audio analyzer. If you want to get the most out of your studio equipment or PA system, the PAA6 should be at the top of your bucket list. A highly accurate measurement tool, the elegant touch screen interface of the PAA6 offers unfettered access to 61-band real-time spectrum analysis; Fast Fourier Transform (FFT); sound pressure (SPL) and dBu/dBV line voltage measurement; EQ setting; phase and polarity check; LEQ (equivalent continuous noise level); audio oscilloscope; and RT-60 functions. The PAA6 also has two built-in condenser measurement mics that can be used in six different positions. If sound is your product or passion, the Phonic PAA6 is perhaps the wisest investment you can make for your studio or sound reproduction system. Whether you're setting up monitors, treating room characteristics, calibrating listening levels, or want to know the harmonic distortion and noise characteristics of your workhorse preamps to ensure clean mixes, the Phonic PAA6 is your key to the best possible quality sound.
-
Product
Voice Coils
-
CAES can tailor a motor for your specific application. This customization can include size variations and winding characteristics to accommodate power supply availability, performance parameters and physical mounting requirements.
-
Product
Pocket Weather Meter
Kestrel 4000
-
The Kestrel 4000 Pocket Weather Meter is the baseline wind and weather meter in the Kestrel 4000 series. What sets the 4000 series apart from the rest of the Kestrel family is that these high tech weather meters have the capability to store up to 2000 points of weather data, enabling you to track changes in the environment over time. This unique function opens up an entirely new realm of weather tracking capabilities for Kestrel Meter users.
-
-
Product
Primary Current Injection Test Set
T 2000
-
T 2000 is a portable current transformer test set which allows to perform many different measurements such as saturation, ratio and polarity tests and CT winding resistance test. Substation maintenance and commissioning test equipment, T 2000 is extremely appreciated by electrical engineers for its high accuracy and portability.
-
Product
Transformer Turns Ratio Meters
-
Vanguard Instruments Company, Inc.
The ATRT-01 S3 is Vanguard’s fourth generation, micro-processor based, single phase, automatic transformer turns-ratio tester. The ATRT-01 S3 uses the IEEE C57.12.90 measuring method to determine the transformer turns-ratio. The transformer turns-ratio is determined by precisely measuring the voltages across the unloaded transformer windings. The ATRT-01 S3’s measuring circuitry self adjusts before each measurement to ensure turns-ratio accuracy. Two selectable test voltages, 4Vac and 40Vac, offer flexibility in testing different types of transformers.
-
Product
Vane Anemometer
AM-4836V
-
Parameters measured: Wind speed, Flow, Beaufort Scale, Wave, Temp., wind directionRange:Wind speed: 0.4-30.0m/s1.4-108.0km/h80-5910ft/min0.8-59.3 knotsFlow: 0.004-9999 m³/min0.013-9999 ft³/minB. Scale: 0-12 forceWave: 0-14mDirection indicator: 16 ways (the resolution is 22.5º)Temp. : 0-60℃ / 32-140℉Accuracy: ±2%n+2Resolution: 0.1/1PC interface: RS232C (Cable & software are optional)Can memorize 50 group dataAuto power offPower supply: 4x1.5V AA A (UM-4) batteryBattery indicator: low battery indicatorDimensions: 156x67x28mm
-
Product
Automatic Transformer Observation System
ATOS
-
Raytech – The World leader in design and manufacturing of high-quality precision measuring instruments and systems, offering flexibility and versatility. Our modular Automatic Transformer Observation System (ATOS) allow you to create a unique and custom solution for any application. ATOS is designed to drastically reduce measuring time and increase test performance, without losing accuracy compared to individual test instruments. With the choice of up to three Multiplexers (primary, secondary, and tertiary), three Winding Resistance Meters, each with three maximum current range options (up to 15A, 50A, or 100A), Turns Ratio, and Integrated power security and safety panel (ISU R), Raytech can create a system with your needs and budget in mind.
-
Product
Capacitor for AC Filtering
PECA5
-
Lifasa - International Capacitors, SA
These capacitors are especially suitable for applications where high levels of AC voltage are required. The design of this series has been optimized for the manufacture of high performance AC filters for compensation equipment with high pollution such as UPS or wind turbines.
-
Product
Anemometers
-
Shenzhen Graigar Technology Co.,Ltd.
An anemometer is a device used for measuring wind speed, and is a common weather station instrument. The term is derived from the Greek word anemos,which means wind, and is used to describe any wind speed measurement instrument used in meteorology .
-
Product
Magnetizer
-
MAGNET-PHYSIK Dr. Steingroever GmbH
Use our magnetizers for everything from the smallest rotors in a wristwatch to wind turbines. We magnetize magnets and magnetic materials of all sizes.
-
Product
Fiber Optics
-
The Neoptix product line includes fiber optic temperature sensors for transformer windings temperature monitoring and for laboratory, industrial, and medical applications.
-
Product
Distribution Transformer Tester
NDB-DOC-3™
-
The NDB-DOC-3™ is a test instrument designed for distribution networks transformers from 5kVA to 3MVA. It can determine the presence of short circuits or open circuits in the distribution transformer primary winding & also short circuits on the secondary winding.The NDB-DOC-3™ is designed to be operated without disconnecting the transformer’s secondary windings from their loads.
-
Product
Wind Power Solution
ECO MITSUBISHI
-
The ECO MITSUBISHI is custom-made with firmware and fixtures designed specifically for Mitsubishi turbines: 1000, 1000A, MWT 2.4. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
Low Voltage Single Phase
600V Class
-
These transformers are encased in a thermoplastic case with the core and windings encapsulated in resin. They are designed for line-to-line operation but may also be used in line-to-neutral or line-to-ground configuration at 58% of rated voltage. It is recommended that a 1.6 Amp fuse be used in the secondary to protect the transformer.
-
Product
3 Phase Voltage Extension To Turns Ratio Meter
T-REX
-
The Raytech three phase voltage system option T-Rex is an optional system accessory for 3-Phase transformer ratio meter test sets designed by Raytech (i.e. TR-MARK III). T-Rex was designed to give Engineers and Test Technicians the ability to test the phase relationships and actual voltage ratios of transformer windings while applying three phase voltage.
-
Product
Fibersim
-
Maya Heat Transfer Technologies Ltd.
The Fibersim portfolio of software for composites engineering from Vistagy, a Siemens PLM company, is used by numerous leading manufacturers in the aerospace, automotive, marine, and wind energy industries. Fibersim supports all of the unique and complex design and manufacturing methodologies necessary to engineer innovative, durable, and lightweight composite products and parts.
-
Product
Anemometers
-
Shenzhen Everbest Machinery Industry Co.,Ltd.
an instrument for measuring the speed of the wind, or of any current of gas.
-
Product
Wind Profilers
-
Bristol Industrial & Research Associates Ltd
Biral provides Sodar systems for the 3-dimensional measurement of wind speed and direction in a vertical column extending hundreds of metres above the sensor. Sodar systems are used in applications such as wind energy site assessment, wind shear detection at airports, plume modelling and basic research.
-
Product
Capacitor for AC Filtering
PECA4 (440V)
-
Lifasa - International Capacitors, SA
These capacitors are especially suitable for applications where high levels of AC voltage are required. The design of this series has been optimized for the manufacture of high performance AC filters for compensation equipment with high pollution such as UPS or wind turbines.
-
Product
Turns Ratio Testing
-
The transformer turns ratio test, or TTR test, confirms that the transformer has the correct ratio of primary turns to secondary turns. Using this test correctly can help to identify tap changer performance, shorted turns, open windings, incorrect winding connections and other faults inside transformers. Megger’s range of TTR testers are robust to withstand the harsh conditions that some transformer testing in. The range includes varying features to simplify and speed up testing as well as 3 phase TTR testers and PT and CT TTR testers.
