Arbitrary Waveform Generators
produce repeating sine, triangle, square, ramp, pulse, or DC waveforms. Also known as: AWG
See Also: Waveform Generators, Waveform Signal Generators, ARB, AWG
-
Product
PXIe 500 MHz Oscilloscope
M9242A
Oscilloscope
500 MHz bandwidth oscilloscope2 analog channels5 GSa/s sample rate1,000,000 wfms/s update rate Isolate signals in seconds with exclusive zone triggering Additional options: 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis and mask testing
-
Product
SWB-2810, 4x43, 1 A, Row Access, Reed Relay Matrix Module for SwitchBlock
781420-10
Reed Relay
4x43, 1 A, Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Cable Assy 37-Pin D-Type F/F 1m
40-970-037-1m-FF
Cable Assembly
The 37-Pin D-Type cable assembly is constructed from 19/0.18 (21 AWG) Tinned Copper Wire. Screwlocks are provided to secure the cable to its associated products.
-
Product
PXI-6723, 13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module
778998-01
Analog Output Module
13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6723 delivers low-cost, high-density analog outputs to meet a wide range of applications, such as stimulus-response, signal simulation, waveform generation, and actuator stimulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6723 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
Cable Assembly, 50-Pin D-Type, Male To Unterminated With Ferrules, 2m HV, 45º Exit Away From Pin 1
40-972-050-2m-MUHV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
CB-37FH, 37-Pin DSUB to Screw Terminal Block w/ Horizontal DIN-Rail Mount
778673-01
Terminal Block
37-Pin Female D-SUB to 37-Pin Female Connector, Horizontal DIN-Rail Terminal Block - The CB-37FH is an unshielded terminal block that provides access to NI data acquisition devices with 37-pin female D-SUB connectors. The CB-37FH mounts in line with the DIN rail, and it features screw or spring terminals for connecting to 37 I/O signals, 12 to 30 AWG.
-
Product
256 GSa/s Arbitrary Waveform Generator
M8199B
Arbitrary Waveform Generator
The M8199B arbitrary waveform generator (AWG) provides R&D engineers with a high-performance arbitrary signal source, enabling design development at 160 GBaud and above. The M8199B AWG enables up to 8 synchronized channels at 256 GSa/s with nominal analog bandwidth exceeding 80 GHz. With integrated frequency and phase response calibration for clean output signals, the M8199B simplifies your test setup.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends, 0.5m HV, Exit Towards Pin 1
A050DF5-T-HA050
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
3-Pin Power D-Type Cable, Male to Unterminated, Tinned Ends, 2m
A003PM5-T-5A200
Cable Assembly
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Mixed Signal Oscilloscope, 100 MHz, 4 Analog Plus 16 Digital Channels
MSOX3014A
Oscilloscope
100 MHz4 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
Oscilloscope - 100 MHz, 2 Analog Channels
DSOX3012T
Oscilloscope
100 MHz2 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
3-Pin Power D-Type Cable, Male to Female, 1m
40-970-403-1m-MF
Cable Assembly
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Signal, Contact, ITA, TriPaddle,7 Amp, 20-24 AWG
610110108
Signal Contact (ITA)
Primary mating contact 610110101. (May mate with other Receiver contacts, as well.)
-
Product
SWB-2815, 4x86, 0.3 A, No Row Access, Reed Relay Matrix Module for SwitchBlock
781421-15
Reed Relay
4x86, 0.3 A, No Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2815 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Waveform Generators
-
UNI-T waveform generators adopt Direct Digital Synthesizer (DDS) technology to generate high frequency signals such as sine waves, square waves, harmonic waves, arbitrary waves, noise etc. Our signal generators also provide analog and digital modulation functions. All models have arbitrary waveform generator with editable software to generate complex waveform. UNI-T has a range of solutions from 5M to 600M to meet your performance needs, including UTG900E series mini generators for hobbyist and UTG9000T high-performance series. With industry leading pricing the UNI-T portfolio of waveform generators provides unparalleled customer value.
-
Product
Arbitrary Waveform Generator
M8199A
Arbitrary Waveform Generator
Get the highest sample rate and the widest bandwidth arbitrary waveform generator in its class with up to four synchronized channels operating simultaneously in one module.
-
Product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781420-17
Relay Matrix Module
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Signal, Contact, Receiver, TriPaddle, 10 Amp, 14-18 AWG
610110128
Signal Contact (Receiver)
Primary mating contact 610110129. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BeCuContact Plating 50µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.41
-
Product
VB-8034, 4-Channel, 350 MHz Bandwidth VirtualBench All-in-One Instrument
784343-04
Multi-Purpose Instrument
4-Channel, 350 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8034 combines a four‑channel, 350 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interactive way to view all your measurements on a single screen and can be updated for free with software releases over time to continually add functionality and value to your VirtualBench. VirtualBench also tightly integrates with LabVIEW software to enable programmatic control and automated test sequences.
-
Product
Oscilloscope
DSOX3032A
Oscilloscope
350 MHz2 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
Power, Patchcord, Receiver, 36", High Power, 2 AWG, Single -Ended (150 Amps)
7-221902000-036
Power Patchcord
Power, Patchcord, Receiver, 36", High Power, 2 AWG, Single -Ended (150 Amps).
-
Product
Oscilloscope - 100 MHz, 4 Analog Channels
DSOX3014T
Oscilloscope
100 MHz4 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Optical Modulation Analyzer and High-speed Digitizer Test Solution
M8290A
-
The M8290A is a flexible solution platform for 400G coherent component and transmitter test. It incorporates a 92 GSa/s modular optical modulation analyzer and a 92 GSa/s 4-channel electrical digitizer. Besides these modules an additional arbitrary waveform generator module up to 92 GSa/s, such as the M8196A, can be added to the same AXIe chassis. This setup results in a compact and flexible coherent test solution that can be used together with additional specialized solution software for Integrated Coherent Receiver (ICR) and Analog Coherent Optical (ACO) module characterization.
-
Product
VB-8054, 4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument
785037-12
Multi-Purpose Instrument
4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8054 combines a four‑channel, 500 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interactive way to view all your measurements on a single screen and can be updated for free with software releases over time to continually add functionality and value to your VirtualBench. VirtualBench also tightly integrates with LabVIEW software to enable programmatic control and automated test sequences.
-
Product
HandyScope HS5 + SureConnect: 100 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 10MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-110XMS-W5
-
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 100 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Cut Ends, 1m HV, Exit Towards Pin 1
A050DM5-C-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Eurocard Plugbord
4614-5
-
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Pad-Per-Hole both sides Voltage and ground buses around board perimeter on both sides Press-fit dual-pole terminal blocks accepts 14-20 AWG wire. Pushbutton release for each pole. Terminal block leads extend 1/8" below bord.Available in 2-pole to 16-pole
-
Product
Cable Assembly, 50-Pin D-Type, Female to Female, 1m HV, Exit Away From Pin 1
40-970-050-1m-FF-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
1.25GS/s 16Bit 1GS Mem 2CH 4 Markers AWG
P1282D
Waveform Generator
The Proteus P1282D, is a 1.25GS/s, dual channel arbitrary waveform generator packaged in a 4U, half 19” dedicated chassis, offering technologically advanced options and configurations that integrate the ability to transmit and perform digital signal processing all in a single instrument. The P1282D offers industry leading performance Including an innovative task oriented programming, real time data streaming, fast feedback loop for environment dependent waveform generation and user customizable FPGA for application specific solutions.
-
Product
Tool, Locator, Mini Coax, 24 AWG Wire
910104128
Locator Tool
Used with Crimp Tool p/n# 910101118 to crimp 24-26 AWG wire to mini coax ITA contacts.
