Relay Drivers
Control the energized state of relays.
-
Product
SIMRC - 16 x Uncommitted Reed Relay, SPST
1010-R-16-1-5/1D
Reed Relay
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
PXI Dual Microwave SPDT Relay 18GHz 50 SMA
40-780A-522
Relay
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 110 GHz, 50 Ω, SMA-1.0, External Termination, Latching
40-781A-921-LA
Relay
The 40-781A-921 (PXI) and 42-781A-921 (PXIe) modules consist of one microwave changeover switch capable of switching up to 110 GHz in 50 Ω. They are available with external terminations and connections are via front panel mounted high quality SMA 1.0 connectors.
-
Product
CMOS Drive High Voltage SIL Reed Relays for up to 3 kilovolts
Series 101
Reed Relay
Direct drive from 74HC/HCT Cmos SIL Relay. Dry or Mercury Wetted switches. 5 Volt coil for 1A dry version is 1600 0r 3000 Ohms
-
Product
LXI Reed Relay Matrix - Single 128x4 Plugin, No Direct Y Access, 6 Analog Buses
65-221-112
Reed Relay
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 40GHz, 50Ω, SMA-2.9, Remote Mount
40-780B-541-E
Relay
The 40-780B-541-E (PXI) and 42-780B-541-E (PXIe) are single SPDT 40GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
PXI/PXIe High Voltage Power Relay Module, 7xSPST With Hardware Interlock
40-323-900-HI
Relay
The 40-323-900 (PXI) and 42-323-900 (PXIe) are 7xSPST relay modules suitable for applications requiring high voltage power switching with high density. They have current handling up to 0.25 A, cold switching up to 9 kVDC/9 kVAC peak and hot switching up to 7.5 kVDC/7.5 kVAC peak.
-
Product
PXI 2A 32xSPST High Density Power Relay Module
40-137-101
Relay
These Power Relay Modules are suitable for applications requiring power relay switching with high density. This version features 2A current and voltage to 110VDC/250VAC, they are configured as Single Pole Single Throw (SPST). Connections are made via front panel mounted 37 or 78-pin D-Type connector.Along with this 32 x SPST version, the range also includes a 39 x SPST, 2A version and a 16 x SPST, 5A version - go to Also in the Range above to learn more.Typical applications will be found in Automotive Test, Aerospace Test and Power Cell Test applications.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 40GHz, 50Ω, SMA-2.9
40-780B-542
Relay
The 40-780B-542 (PXI) and 42-780B-542 (PXIe) are dual SPDT 40GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
PXI Ultra High Density Reed Relay Matrix, 33x16, 1-Pole
40-542A-021
Reed Relay
The 40-542A-021 is part of a range of ultra high density matrices. The 40-540A/541A/542A are the world’s highest density single slot PXI reed relay matrix modules and are available as a 132x4, 66x8 or 33x16 matrix with 1-pole switching.
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 67GHz, 50Ω, SMA-1.85, Remote Mount
40-780B-573-E
Relay
The 40-780B-573-E (PXI) and 42-780B-573-E (PXIe) are triple SPDT 67GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions.
-
Product
PXI/PXIe Power Relay Module,5 Amp, 50-pin SGMC Connectors
40-153-002-HI
Relay
The 40/42-153-002-HI is a PXI/PXIe high density power relay module with 36xSPST switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock.
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 64xSPDT
40-148A-201
Relay
The 40-148A-201 (PXI) and 42-148A-201 (PXIe) 64xSPDT relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
PXI Power Relay Module, 12xSPDT, 16 A
40-161A-101
Relay
The 40/42-161A-101 is a PXI/PXIe 12xSPDT power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock. Electro-mechanical power relays are used wich are suitable for switching loads up to 16 A at 250 VAC.
-
Product
LXI Scalable Switched Guard Matrix - 8x16 Plugin Module
65-290-002
Reed Relay
The 65-290-002 is an 8x16 matrix plug-in module for use in Pickering's modular switching platform that provides a switched guard relay matrix solution with up to 1012 Ω channel to channel and channel-to-ground isolation.
-
Product
PXIe-2569, 100-Channel, 1 A, SPST PXI Relay Module
780587-69
Relay
PXIe, 100-Channel, 1 A, SPST PXI Relay Module—The PXIe‑2569 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. It is fully software programmable and contains a 32,000‑step scan list for deterministic scanning capability. This module offers maximum relay density, so it is ideal for medium-power automated test loads.
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 100xSPST, Normally Closed
40-145A-201-NC
Relay
The 40-145A-201-NC (PXI) and 42-145A-201-NC (PXIe) 100xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 50 GHz, 50 Ω, SMA-2.4, Remote Mount, Failsafe
42-780B-553-E
Relay
The 40-780B-553-E (PXI) and 42-780B-553-E (PXIe) are triple failsafe SPDT 50 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
LXI Reed Relay Matrix - Dual 32x16 Plugin, Direct Y Access, 3 Analog Buses
65-225-001
Reed Relay
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
Product
PXI Microwave Relay, Single SPDT, 26.5 GHz, 50 Ω, SMA, Failsafe
40-780B-531
Microwave Relay Module
The 40-780B-531 (PXI) and 42-780B-531 (PXIe) are single failsafe SPDT 26.5 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 50GHz, 50Ω, SMA-2.4
40-780B-552
Relay
The 40-780B-552 (PXI) and 42-780B-552 (PXIe) are dual SPDT 50GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781420-11
Reed Relay
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 18 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-780B-523-E
Relay
The 40-780B-523-E (PXI) and 42-780B-523-E (PXIe) are triple failsafe SPDT 18 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
PXI 8 x DPST Power Relay Module, 5A
40-150-002
Relay
40-150/151 modules have 8xDPST or 12xDPST power relays, suitable for switching inductive/capacitive loads up to 5A at 250VAC. 40-155/156 modules have 8xSPDT or 16xSPDT power relays and 40-157 is configured as 8xDPDT.
-
Product
PXIe Microwave Relay, Triple SPDT, 26.5 GHz, 50 Ω, SMA, Failsafe
42-780B-533
Microwave Relay Module
The 40-780B-533 (PXI) and 42-780B-533 (PXIe) are triple failsafe SPDT 26.5 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
PXI Switched Guard Reed Relay Module, 13x SPST
40-121-002
Reed Relay
The 40-121-002 provides 13x SPST switches in a single slot PXI module and designed to provide an isolation resistance in excess of 1013Ω. It has been designed to ensure high isolation resistance through the use of switched guards, making it ideal for low level measurements and semiconductor test.
-
Product
PXI Mixed Configuration Relay Module - 11 Cells Populated
40-138-AA-BB-CC-DD (11 CELL)
Relay
The 40-138 2A Relay Module with 11 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
PXI Single Microwave SPDT Relay 2.5GHz 75 1.6/5.6
40-780A-751
Relay
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
Product
PXI Switched Guard Reed Relay Module, 26x SPST
40-121-001
Reed Relay
The 40-121-001 provides 26x SPST switches in a single slot PXI module and designed to provide an isolation resistance in excess of 1013Ω. It has been designed to ensure high isolation resistance through the use of switched guards, making it ideal for low level measurements and semiconductor test.
-
Product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 75Ω, MCX
40-830A-103
Relay
The 40-830A-103 (PXI) and 42-830A-103 (PXIe) are 75Ω RF switches with 3 separate SPDT relays in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-830A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
