Energy Monitors
Measure the consumption of electricity.
-
Product
Renewable Energy
-
ETAP's Renewable Energy offering enables designers and engineers to conceptualize the collector systems, determine wind and PV solar penetration and perform grid interconnection studies.
-
Product
System Controllers & Battery Monitors
-
UNIPOWER System Controllers & Battery Monitors provide battery management functionality for the Aspiro, Guardian and Sageon DC Power Systems. The proprietary PowCom software enbles the user to monitor multiple Aspiro or Guardian systems at different locations using a highly intuitive GUI. SageView software provides similar fucntionality for Sageon systems and also works with the standalone Sageon Shield battery monitor.
-
Product
Digital RF Power Monitor
3024
-
The COMM-connect 3024 RF Power Monitor from LBA Technology can control up to 8 external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. The Power conversion algorithms handles multi carrier, multi mode, peak, average and RMS signals. The power readout is auto scaled and VSWR can be calculated between any probes. Also the measured and calculated results along with alarms can be shown in the local LCD. The instrument has SNMP support to allow network management. The instrument can be configured for VSWR and Power limits to give alarms. The alarms can be configured to operate relay drivers or isolated Optcouplers. The alarms can also be configured as SNMP traps sending relevant information to the network control center. The COMM-connect 3024 WEB enabled RF Power Monitor gives an unlimited number of applications to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
Product
Control & Monitoring
-
Omega has a large selection of control and monitoring devices to chose from. Omega devices can measure anything from gas, liquid, or temperature to process voltages and currents, and much more!
-
Product
Object Monitoring
IROD
-
IROD – automatic system for thermographic object monitoringAutomatic detection of intruders based on minimum temperature changesAlerting even in case of darkness or poor visibilityNo additional IT illumination necessary
-
Product
Portable Single Gas Monitor
Protégé ZM
-
Teledyne Gas & Flame Detection
The Protégé ZM single gas monitor is an easy-to-use, zero maintenance gas detection solution that delivers high performance in a small, ergonomically designed package. It is available in oxygen, carbon monoxide and hydrogen sulphide single gas models. This single gas monitor is incredibly reliable, giving industrial workers and first responders the confidence to focus on the task at hand, not on their equipment.
-
Product
Advanced Active/Passing Monitoring System
SQmediator
-
SQmediator® is an advanced active/passive monitoring system engineered to proactively manage the end-to-end performance of a range of network applications, including Voice over IP, IP Videoconferencing, Web and Email. Its multi-service, multi-tenant architecture supports advanced data aggregation, one-click custom dashboards for customers and locations, per-metric service thresholds, real-time alerts, and a web services API for integration with external management systems
-
Product
Control Room Oxygen Monitor
Model 3350
-
Teledyne Analytical Instruments
The Model 3350 accurately measures the concentration of oxygen in control rooms, closed atmospheres, critical breathing circuits and other applications that require the fail-safe monitoring of breathable, ambient air. It is a microprocessor-based oxygen alarm monitor for real-time measurement of the oxygen content of the atmosphere surrounding the sensor as well as shoulders the burden of personal safety with the quality and reliability offered by the Teledyne name.
-
Product
Cell Culture & Cell Monitoring Solutions
-
Improve and streamline your cell culture processes with Olympus’ innovative cell culture and cell monitoring equipment. At Olympus, we offer equipment to support processes through a range of cell culture analysis stages, including cell culture microscopes and cell monitoring equipment and software.
-
Product
Water Distribution Monitor
TW-100
-
HORIBA’s TW-100 is a process water quality measurement system designed for drinking water and water distribution plants. The TW-100 monitors turbidity, color, free chlorine and pressure. This chemical free method reduces operating costs as it requires minimal maintenance and improves process control.
-
Product
Radiation Portal Monitors
-
Baltic Scientific Instruments, Ltd
Radiation Portal Monitors (RPM) are fix-installed radiation detection systems designed for automated screening of pedestrians, vehicles and trains passing through the detection zone of RPM for presence of gamma and neutron radiation. The RPM alerts the security office and front line officer about the presence of radioactive and nuclear material and provides additional alarm associated information: type of alarm (gamma, neutron or both), relative amplitude of the alarm, etc.
-
Product
Portable Temperature Monitor
PTM1
-
The Model PTM1 is a high performance, precision hand-held instrument for the measurement of temperature using Physitemp’s Type T (copper-constantan) thermocouples (will also accept J & K). This versatile instrument measures temperature in both °C and °F. The internal memory of the microcomputer stores the minimum and maximum measured temperature range for instant recall via the LCD display.
-
Product
Opacity Monitor
DT1000
-
The Datatest Model 1000 is a microprocessor based EPA compliance opacity monitor. The microprocessor creates excellent stability and reliability plus the use of patented glass fiber optic technology in the stack components further enhances the performance. The Model 1000 is offered in a double pass Model 1000 MPD version or a single pass Model 1000 MPS (suitable for harsh applications).
-
Product
Camera Endpoint Monitor based on Real Time Laser Interferometry
LEM Series
-
Our Real Time Interferometric Process Monitor provides high precision detection of film thickness and trench depth during the etching/deposition process.Depending on applications, LEM camera includes a 670 or 905 or 980 nm laser and when mounted on any dry etch/deposition process chamber with a direct top view of the wafer this generates a small laser spot on the sample surface.Interference occurs when monochromatic light hits the sample surface, resulting in different optical path lengths due to film thickness and height variations in the film.This allows the etch/deposition rate and thus thickness to be monitored in real time, also fringes counting or more complex analysis, providing enhanced process control Endpoint for a wide variety of processes. Additionally interfaces can be detected by their change in reflectivity.
-
Product
Gas Monitor
TG5000
-
The TG5000 Gas Monitor is an effective and economical solution to detecting combustible and toxic gases, as well as oxygen deficiency/enrichment, in wastewater, commercial and light industrial applications. The TG5000 helps personnel to work safely in these environments offering a variety of sensor and configuration options.
-
Product
ABex Current Sense Module for Six Channel UUT Supply Monitoring
ABex TM-406 Current Sense
-
The ABex TM-406 is a six-channel shunt current measurement extension. It’s designed to work in combination with the Konrad ABex TM-501 and PXI-501.Each of the six shunt current measurement units have a passive measurement shunt, an overcurrent protection, a sense bridge relay and the possibility to route the quiescence current to an ABex measurement device TM-501 with PXI-501.In addition, the ABex TM-406 features 8 isolated digital outputs (IDOs), and 12 measurement inputs, which can be routed to the analog bus.
-
Product
Non-Destructive Particle Monitoring
PARTi
-
PARTi provides a complete solution for non-destructive surface particle monitoring of consumables, parts and cleanroom apparel.
-
Product
Monitoring Products
-
The motor condition monitoring device with the ability to quantify the status of a three-phase induction motor and incorporating EtherNet/IP communication to trend information on current analysis, motor vibration, motor temperature, and insulation resistance.
-
Product
Charged Plate Monitor
Model 280A
-
Simco-Ion’s Model 280A incorporates enhanced circuitry that enables it to more accurately measure the performance of high frequency AC ionizers, as well as pulsed DC ionizers and steady-state DC ionizers. The Model 280A can be used as a portable CPM and is capable for of up to 6 hours of operation on the internal battery before recharge.
-
-
Product
Area/process radiation monitoring
-
Monitors gamma and beta rays/ neutron with high accuracy and reliability. *Each monitor is controlled with central control system and alarm is given when the measurement exceeds alarm level. Area monitors and dust monitors.
-
Product
Battery Monitoring Systems
-
Franklin Electric - Grid Solutions
Combines wireless communication with patented, field-proven battery conductance analysis technology. It lowers total cost of ownership while providing the most thorough and easy to access stationary battery health diagnostics.
-
Product
Application-centric Monitoring & Migrations
Ulia
-
Uila provides real-time visibility into the Application & Business Service Dependencies and also powers the IT teams with deep insights into web and database applications to allow for the issues to be narrowed down and mitigated.
-
Product
Hydrogen Fluoride Gas Monitor
GASERA ONE HF
-
Hydrogen fluoride, chemical formula HF, is a colorless, highly irritating already at very low ppm levels, corrosive gas and can exist as a fuming liquid. Reaction with water is rapid, producing heat and hydrofluoric acid. Hydrogen fluoride (HF) is used in manufacturing of refrigerants, herbicides, pharmaceuticals, high-octane gasoline, aluminum, plastics, electrical components, and fluorescent light bulbs, among others. Hydrogen fluoride (HF) is very soluble in water and is readily absorbed in the upper respiratory tract.
-
Product
Spectrum And Signal Monitoring
-
Kratos Defense & Security Solutions, Inc.
With the rapid growth of satellite networks including VSATs, there is the potential for increased Radio Frequency Interference (RFI). Interfering signals can be periodic or occur at different frequencies over time, making the discovery and removal of these sources a significant challenge.
-
Product
Workstation Monitors
-
Dou Yee Enterprises (S) Pte Ltd
Dou Yee Enterprises Workstation Monitors including critical process electrostatic moinitoring, event monitor embeddable ERDS monitoring, and multi-channel field voltage detection
-
Product
Non-Dispersive Infrared Monitors
OPTI-Sense Series
-
Teledyne Advanced Pollution Instrumentation
The OPTI-Sense series of sensors is based on Non-Dispersive Infrared (NDIR) technology. They are designed to precisely measure the absorbance in the infrared spectrum of specialty gases typically found in semiconductor applications. They are very compact and designed with no moving parts, making the OPTI-Sense robust and ideal for continuous in-situ gas monitoring of semiconductor processes.
-
Product
Battery Monitoring
-
Eagle Eye Power Solutions’ advanced battery monitoring systems are designed to optimize performance, enhance safety, and ensure compliance. Explore reliable solutions for real-time monitoring and maintenance of critical power systems.
-
Product
Continuous Emission Monitoring Systems
-
TML has more than 50 years' experience designing, manufacturing, and supporting continuous emission monitoring systems (CEMS). We have a team of experienced CEMS air quality experts that will thoroughly review your process and operating permit and recommend the most cost effective and reliable solution for monitoring the gases of interest. TML's continuous emission monitoring systems are based on rugged, reliable equipment manufactured to exact standards. The result is products and systems with some of the highest mean time between failure rates in the industry. Whether it's a standard or custom solution, we stand behind our products 110%, guarantee CEMS certification, at least 95% uptime, replacement parts, and 24 x 7 support. We offer a total CEMS solution including data acquisition software for recordkeeping and reporting, lower cost of ownership, superior product reliability and designed for simple and easy maintenance.
-
Product
2 Channel IV Analyzer / Source Monitor Unit
E5263A
-
Keysight E5262A and E5263A 2ch IV Analyzers are the low cost solution for current-voltage characterization. The E5262A and E5263A support two channels of SMUs (Source/Monitor Units) for voltage/current sourcing and voltage/current measurement with the best in the class current measurement performance as low as 5 pA. The Easy EXPERT group+ GUI based characterization software is furnished and available on your PC to support all the tasks required in the characterization from the measurement setup to the data analysis. Powerful integration of SMU's versatile measurement capabilities and GUI based characterization software makes the E5262A and E5263A the best solutions for characterization and evaluation of two or three terminal devices such as materials and active/passive components with uncompromised measurement reliability and efficiency.
